Go Back   The Ford Barn > General Discussion > Early V8 (1932-53)

Sponsored Links (Register now to hide all advertisements)

Reply
 
Thread Tools Display Modes
Old 11-05-2020, 08:52 PM   #1
53_mercLuke
Member
 
Join Date: May 2016
Location: Houston TX
Posts: 79
Default 1901 teapot question

I know everyone says to throw them away but I haven't had much issue with mine. My question is, is there a way to kind of hop them up alittle bit? I have looked around and haven't seen much of it. I plan on upgrading down the road but was just curious if anyone has modified them to get alittle more out of them for the time being

Thanks
53_mercLuke is offline   Reply With Quote
Old 11-05-2020, 09:10 PM   #2
wga
Senior Member
 
wga's Avatar
 
Join Date: Jul 2010
Location: Yorba Linda, CA
Posts: 887
Default Re: 1901 teapot question

If I understand correctly, you want to make a tempest in a teapot?
__________________
Henry Ford designed the flathead without the aid of a computer.
wga is offline   Reply With Quote
Sponsored Links (Register now to hide all advertisements)
Old 11-05-2020, 09:16 PM   #3
53_mercLuke
Member
 
Join Date: May 2016
Location: Houston TX
Posts: 79
Default Re: 1901 teapot question

Haha sure.. I think haha? I just want to see if its possible to step them up in performance alittle
53_mercLuke is offline   Reply With Quote
Old 11-05-2020, 09:20 PM   #4
tubman
Senior Member
 
tubman's Avatar
 
Join Date: Dec 2013
Location: Minnesota, Florida Keys
Posts: 10,259
Default Re: 1901 teapot question

I'm not an expert on these by any means, but I would think that anything that would increase performance would have an adverse effect on fuel economy and driveability. Even if you could get a small performance increase, it would be almost imperceptible by "the seat of your pants". The one upgrade that may help is boring out the manifold to match a small base 2G and use one of those.
tubman is offline   Reply With Quote
Old 11-05-2020, 09:45 PM   #5
53_mercLuke
Member
 
Join Date: May 2016
Location: Houston TX
Posts: 79
Default Re: 1901 teapot question

Thanks tubman, I was just curious. I was there wouldn't be a big performance upgrade for a teapot but just been thinking about it as of late. I really don't have any issues with mine now so I was debating on changing it if there was anyways. Ill look into the manifold though
53_mercLuke is offline   Reply With Quote
Old 11-06-2020, 08:40 AM   #6
rotorwrench
Senior Member
 
rotorwrench's Avatar
 
Join Date: Jun 2010
Location: San Antonio, Texas
Posts: 16,367
Default Re: 1901 teapot question

Sponsored Links (Register now to hide all advertisements)
The Mercury 885 and 1901 carbs were the top of the heap for heavy cars & big trucks back in the day but the performance aspect was seldom considered since most folks wanted 2 or 3 Stromberg 97s with an aftermarket distributor. The carburetor and distributor are a system designed by Holley to work together. They are fine for mild street performance in stock form but not so much for serious competition.
rotorwrench is offline   Reply With Quote
Old 11-06-2020, 11:20 AM   #7
scicala
Senior Member
 
scicala's Avatar
 
Join Date: Jun 2010
Location: Detroit suburb, MI
Posts: 3,697
Default Re: 1901 teapot question

Quote:
Originally Posted by 53_mercLuke View Post
I know everyone says to throw them away but I haven't had much issue with mine. My question is, is there a way to kind of hop them up alittle bit? I have looked around and haven't seen much of it. I plan on upgrading down the road but was just curious if anyone has modified them to get alittle more out of them for the time being

Thanks
This carb and most others are originally calibrated for peak HP at a certain RPM. The only way to increase the power is to increase the air flow and recalibrate the main jet accordingly. It would be a difficult task if you wanted to open up the venturi's to get the extra flow. I would recommend a Rochester 2gc that has the same bolt pattern to increase air flow and performance.

Sal
scicala is offline   Reply With Quote
Old 11-07-2020, 10:34 AM   #8
Ol' Ron
Senior Member
 
Ol' Ron's Avatar
 
Join Date: May 2010
Location: Chester Vt
Posts: 8,840
Default Re: 1901 teapot question

2GCc and a GM dist is the answer.
Ol' Ron is offline   Reply With Quote
Old 11-07-2020, 10:37 AM   #9
wga
Senior Member
 
wga's Avatar
 
Join Date: Jul 2010
Location: Yorba Linda, CA
Posts: 887
Default Re: 1901 teapot question

If you want to go EFI, Holly has you covered - 2GC throttle body EFI

https://www.holley.com/products/fuel...parts/550-866K
__________________
Henry Ford designed the flathead without the aid of a computer.
wga is offline   Reply With Quote
Old 11-07-2020, 01:40 PM   #10
tubman
Senior Member
 
tubman's Avatar
 
Join Date: Dec 2013
Location: Minnesota, Florida Keys
Posts: 10,259
Default Re: 1901 teapot question

On my way back from the post office today, I stopped at my shop and threw a caliper on a Merc manifold and a 2G, just to see how much difference there was. The throttle bores in the Merc Manifold were 1.300", while the 2G has 1.4375" throttle bores. A little basic math and I came out with a total throttle bore area of 2.654 sq in for the stock Merc setup and 3.418 sq in for the 2G. That means the throttle bore area of a 2g is almost 30% larger than the Merc. Definitely a significant improvement.

Of course, this means that, although the 2G will bolt to the Merc manifold, it won't do a lot of good unless you bore the manifold out to the 2G size. I have done this on both aluminum (Canadian) and cast iron manifolds without a problem. I used a scrap 2G base as a guide and a tool called a "Rota-Broach" in my $89.95 Northern Tool benchtop drill press. The cast iron cut easily, not to mention the aluminum.

Then again, if you want to get the cheapest performance increase from a flathead, have the heads milled for increased compression and optimum quench. This is not just a plain mill job, but requires some measuring before to determine the optimum cut (which may not be the same on each side) and some work with a die grinder after to get uniform clearance over the piston. Valve to head clearance is not a problem with mild cams.

Last edited by tubman; 11-07-2020 at 01:49 PM.
tubman is offline   Reply With Quote
Old 11-07-2020, 01:48 PM   #11
tubman
Senior Member
 
tubman's Avatar
 
Join Date: Dec 2013
Location: Minnesota, Florida Keys
Posts: 10,259
Default Re: 1901 teapot question

Quote:
Originally Posted by wga View Post
If you want to go EFI, Holly has you covered - 2GC throttle body EFI

https://www.holley.com/products/fuel...parts/550-866K
That setup looks real interesting. I'd sure like to try one. However, the price is quite discouraging and I don't suppose it comes in a 6 volt positive ground version.
tubman is offline   Reply With Quote
Old 11-07-2020, 08:15 PM   #12
Ol' Ron
Senior Member
 
Ol' Ron's Avatar
 
Join Date: May 2010
Location: Chester Vt
Posts: 8,840
Default Re: 1901 teapot question

Yes, almost 2 grand for the complete system. I wonder how conr=trolable the ignition is. Like vacuum advance under load.???
Ol' Ron is offline   Reply With Quote
Old 11-08-2020, 05:15 PM   #13
Robz51
Senior Member
 
Robz51's Avatar
 
Join Date: May 2010
Location: Rogers, AR, USA
Posts: 141
Default Re: 1901 teapot question

I've had pretty good luck with mine. Ethanol gas is a not good for these carbs. The varnish gums them up and they leak-alot! I think they get a bad rap. I had Sal Cicala rebuild mine and I runs great.

Sent from my SM-G955U1 using Tapatalk
Robz51 is offline   Reply With Quote
Old 11-09-2020, 11:17 AM   #14
scicala
Senior Member
 
scicala's Avatar
 
Join Date: Jun 2010
Location: Detroit suburb, MI
Posts: 3,697
Default Re: 1901 teapot question

Quote:
Originally Posted by Robz51 View Post
I've had pretty good luck with mine. Ethanol gas is a not good for these carbs. The varnish gums them up and they leak-alot! I think they get a bad rap. I had Sal Cicala rebuild mine and I runs great.

Sent from my SM-G955U1 using Tapatalk
I agree. Teapot style carbs get a bad rap and a lot of old tales, mostly by people that don't even touch carburetors.

Sal
scicala is offline   Reply With Quote
Old 11-09-2020, 01:04 PM   #15
tubman
Senior Member
 
tubman's Avatar
 
Join Date: Dec 2013
Location: Minnesota, Florida Keys
Posts: 10,259
Default Re: 1901 teapot question

If your car is stock, I would also suggest getting the "Teapot" redone. Going to anything else leads to linkage, fuel line, and air cleaner incompatibility. We're lucky to have an expert like Sal available. I would take advantage of his services, especially since you have two of these.
tubman is offline   Reply With Quote
Old 11-13-2020, 11:59 AM   #16
Brendan
Senior Member
 
Brendan's Avatar
 
Join Date: May 2010
Location: At my kitchen table in Santa Rosa, Ca
Posts: 2,902
Default Re: 1901 teapot question

Quote:
Originally Posted by wga View Post
If I understand correctly, you want to make a tempest in a teapot?
i would rather have a Coffee Pot...LOL
__________________
If it would have been a snake it would have bit ya!

i can't spell my way out of a paper bag!
Brendan is offline   Reply With Quote
Reply

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump

Sponsored Links (Register now to hide all advertisements)


All times are GMT -5. The time now is 03:51 AM.