Go Back   The Ford Barn > General Discussion > Model A (1928-31)

Sponsored Links (Register now to hide all advertisements)

Reply
 
Thread Tools Display Modes
Old 05-07-2021, 05:17 PM   #1
springerpete
Senior Member
 
springerpete's Avatar
 
Join Date: Jul 2012
Location: Central Maine
Posts: 643
Default dropping the pan

I'd like opinions on what is involved here. There is very little room between the pan and the bolt heads to fit a 1/2" socket. I have a thin wall socket but still had problems. What do you folks do ? It is worse on the rear of the engine . Always willing to see other opinions.
springerpete is offline   Reply With Quote
Old 05-07-2021, 05:25 PM   #2
Synchro909
Senior Member
 
Synchro909's Avatar
 
Join Date: Jun 2014
Location: Melbourne, Australia
Posts: 7,472
Default Re: dropping the pan

Getting at those bolts is tight at the front and the back. My cars are drivers so I cut a slot in the heads of the bolts and use a square shanked screw driver. You clearly have hex heads so just keep at it. They'll all give up the fight in the end.
__________________
I'm part of the only ever generation with an analogue childhood and a digital adulthood.
Synchro909 is offline   Reply With Quote
Sponsored Links (Register now to hide all advertisements)
Old 05-07-2021, 05:46 PM   #3
jb-ob
Senior Member
 
Join Date: Jun 2010
Posts: 631
Default Re: dropping the pan

Pete,

Be easy on yourself, jack up the front end and turn the steering to one side, locked. That will move the tie rod away from the front of the oil pan.

Yes a thin wall deep socket will reach, but when re-assembling only use a 1/4 drive ratchet so you don't find out how easy it is to snap a bolt in an difficult spot.......jb
jb-ob is offline   Reply With Quote
Old 05-07-2021, 05:47 PM   #4
Flathead
Senior Member
 
Flathead's Avatar
 
Join Date: May 2010
Location: Southern Maine
Posts: 1,493
Default Re: dropping the pan

Try using a 1/4" drive socket set, it works well on the rear pan bolts too.
Flathead is offline   Reply With Quote
Old 05-07-2021, 05:48 PM   #5
Jacksonlll
Senior Member
 
Jacksonlll's Avatar
 
Join Date: Jul 2012
Location: Michigan-- Member of Oakleaf of MARC
Posts: 1,686
Send a message via ICQ to Jacksonlll
Default Re: dropping the pan

Be sure to turn your wheels all the way to one side or the other. This gets your tie rod out of the way. A quarter inch socket set works good.
Jacksonlll is offline   Reply With Quote
Old 05-07-2021, 05:57 PM   #6
Mister Moose
Senior Member
 
Mister Moose's Avatar
 
Join Date: Jun 2020
Location: Hartford area, CT
Posts: 374
Default Re: dropping the pan

Sponsored Links (Register now to hide all advertisements)
There's been numerous occasions fixing things where I needed to make/alter my own tools. Almost always has to do with access or clearance. In this case, what about buying the right size offset box wrench, and cut the rim off slightly as needed:


Wrench.jpg


All this tool needs to do is function as a breaker bar, you can spin it out the rest of the way with something else. If you need more leverage, slide a pipe over it.
Mister Moose is offline   Reply With Quote
Old 05-07-2021, 06:00 PM   #7
mercman from oz
Senior Member
 
mercman from oz's Avatar
 
Join Date: May 2012
Location: Queensland, Australia
Posts: 10,295
Default Re: dropping the pan

mercman from oz is offline   Reply With Quote
Old 05-07-2021, 07:05 PM   #8
Tom Endy
Senior Member
 
Tom Endy's Avatar
 
Join Date: May 2010
Location: Southern California
Posts: 3,122
Default Re: dropping the pan

Get some threaded stock the same thread size as the pan bolts. cut four pieces about two inches long and put a nut on them. Remove two bolts on each side and screw the four studs in place. Now when you take the other bolts out you will be able to let the pan drop onto the studs when the gasket breaks loose. They also come in handy when re-installing.

Remove the dripper tray to clean out the bottom of the pan. Use a long wooden hammer handle (a baseball bat works better). Put it down in the hole for the oil pump, Put your foot on the top of the pan and give a sharp thrust of the handle.

Use your foot to reinstall the dipper tray. Make sure you have it in place in the slots correctly.

When you re-install the pan glue the gasket to the top of the pan, do not put sealer on the top of the gasket, use axle grease. This way it will be easier to remove next time and you won't have to scrape pieces of gasket off the engine pan rails.

Tom Endy
Tom Endy is online now   Reply With Quote
Old 05-07-2021, 07:05 PM   #9
JayJay
Senior Member
 
Join Date: Jan 2020
Location: SF Bay Area
Posts: 1,044
Default Re: dropping the pan

Quote:
Originally Posted by Flathead View Post
Try using a 1/4" drive socket set, it works well on the rear pan bolts too.
In my tools the 1/4" drive deep socket has a thinner wall than the short socket, so I use the 1/4" drive deep socket. (I think the 1/4" deep sockets are Craftsman I bought back when Craftsman was still Craftsman).

JayJay
__________________
JayJay
San Francisco Bay Area

------------------------
1930 Murray Town Sedan
1931 Briggs S/W Town Sedan
JayJay is online now   Reply With Quote
Old 05-07-2021, 07:16 PM   #10
700rpm
Senior Member
 
700rpm's Avatar
 
Join Date: May 2010
Location: Portland, Oregon
Posts: 5,892
Default Re: dropping the pan

I use a 1/4” socket with a six inch extension and pan guides.
__________________
Ray Horton, Portland, OR


As you go through life, keep your eye on the donut, not the hole.

Last edited by 700rpm; 05-07-2021 at 10:20 PM.
700rpm is offline   Reply With Quote
Old 05-07-2021, 07:52 PM   #11
Ruth
Senior Member
 
Join Date: May 2016
Location: Glide, Oregon
Posts: 1,334
Default Re: dropping the pan

Quote:
Originally Posted by Tom Endy View Post
Get some threaded stock the same thread size as the pan bolts. cut four pieces about two inches long and put a nut on them. Remove two bolts on each side and screw the four studs in place. Now when you take the other bolts out you will be able to let the pan drop onto the studs when the gasket breaks loose. They also come in handy when re-installing.


Tom Endy
i use Oil Pan Guides that are made for this purpose.
https://www.snydersantiqueauto.com/P...earchByKeyword
__________________
Ruth
"Sometimes you really DO need to read the whole thread"
Ruth is online now   Reply With Quote
Old 05-08-2021, 12:25 AM   #12
Synchro909
Senior Member
 
Synchro909's Avatar
 
Join Date: Jun 2014
Location: Melbourne, Australia
Posts: 7,472
Default Re: dropping the pan

I've never used guides to put the sump back on. I hold the A frame with one hand so that my forearm is under the sump. Once I lift it high enough to get my arm under it, it is easy to lift it into place by bending my wrist. I have a screw already set up in a socket on the battery powered (very low powered) rattle gun. One goes in VERY easily. The next is no more difficult, then you're pretty much finished.
__________________
I'm part of the only ever generation with an analogue childhood and a digital adulthood.
Synchro909 is offline   Reply With Quote
Old 05-08-2021, 10:05 AM   #13
katy
Senior Member
 
katy's Avatar
 
Join Date: Jun 2015
Location: Red Deer, Alberta
Posts: 5,011
Default Re: dropping the pan

Quote:
Originally Posted by mercman from oz View Post
3/4" is a little big for the pan bolts
__________________
If you don't hear a rumor by 10 AM, start one!.
Got my education out behind the barn!
katy is online now   Reply With Quote
Old 05-08-2021, 10:58 AM   #14
springerpete
Senior Member
 
springerpete's Avatar
 
Join Date: Jul 2012
Location: Central Maine
Posts: 643
Default Re: dropping the pan

Wow, thanks for all the suggestions. My issue is clearance between the bolt head and the pan flange. I did turn the wheels for extra space. I could not find a 1/4" drive, thin wall deep socket but I do have a regular deep socket and just up the street is a machine shop. I will have them thin it out till it fits. Pan came down easily and tray came out when I dropped the pan on a layer of cardboard. Thanks again for all the suggestions, I've made notes fopr use later. Bill
springerpete is offline   Reply With Quote
Old 05-08-2021, 01:10 PM   #15
Flathead
Senior Member
 
Flathead's Avatar
 
Join Date: May 2010
Location: Southern Maine
Posts: 1,493
Default Re: dropping the pan

Cheap foreign made sockets are ideal to grind down for special applications like this and should be strong enough for pan bolts. Good use for an odd or homeless socket.
Flathead is offline   Reply With Quote
Old 05-08-2021, 01:54 PM   #16
Mister Moose
Senior Member
 
Mister Moose's Avatar
 
Join Date: Jun 2020
Location: Hartford area, CT
Posts: 374
Default Re: dropping the pan

Quote:
Originally Posted by springerpete View Post
My issue is clearance between the bolt head and the pan flange.
Why did they make the flange so close to cause interference with normal tools?
What tool did the factory use? (Rhetorical question)
What tool do the rebuilders use?
Mister Moose is offline   Reply With Quote
Old 05-08-2021, 03:42 PM   #17
noyo55
Member
 
Join Date: May 2010
Posts: 75
Default Re: dropping the pan

Back about 1965 I had a fellow come up to me and asked about my coupe. he asked if I had problems with removing the pan bolts. He then said that he had a special speed wrench made for this. the next day he came by where I worked and handed it to me. A great gift and used many times. there must be more of these out there.
noyo55 is offline   Reply With Quote
Old 05-08-2021, 07:47 PM   #18
shew01
Senior Member
 
shew01's Avatar
 
Join Date: Sep 2016
Location: Roanoke, VA USA
Posts: 1,905
Default Re: dropping the pan

Quote:
Originally Posted by noyo55 View Post
Back about 1965 I had a fellow come up to me and asked about my coupe. he asked if I had problems with removing the pan bolts. He then said that he had a special speed wrench made for this. the next day he came by where I worked and handed it to me. A great gift and used many times. there must be more of these out there.

I’m curious. Could you post a picture?


Sent from my iPhone using Tapatalk
shew01 is offline   Reply With Quote
Old 05-09-2021, 09:27 AM   #19
katy
Senior Member
 
katy's Avatar
 
Join Date: Jun 2015
Location: Red Deer, Alberta
Posts: 5,011
Default Re: dropping the pan

I just R&Rd the pan on my A yesterday, used a regular 6 point, 3/8" drive, S-K socket, no interference problems.

FWIW, that socket has been in use for over 60 years, so it's probably a little sloppy.
__________________
If you don't hear a rumor by 10 AM, start one!.
Got my education out behind the barn!

Last edited by katy; 05-10-2021 at 10:40 AM. Reason: Addition
katy is online now   Reply With Quote
Old 05-10-2021, 08:03 AM   #20
Patrick L.
Senior Member
 
Patrick L.'s Avatar
 
Join Date: May 2010
Location: Largo Florida
Posts: 7,225
Default Re: dropping the pan

I just use a wobble socket. Its easy enough to grind the wall thinner if needed. After awhile the tool box gets full of stuff that has been specially 'adjusted'.
Patrick L. is offline   Reply With Quote
Reply

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump

Sponsored Links (Register now to hide all advertisements)


All times are GMT -5. The time now is 07:42 PM.