|
Sponsored Links (Register now to hide all advertisements) |
|
|
Thread Tools | Display Modes |
08-19-2020, 07:56 PM | #1 |
Senior Member
Join Date: Dec 2013
Location: Waxahachie, Texas
Posts: 949
|
'40 Ford carb fine tuning help needed
Stock '40 engine with about 5,000 miles since rebuild. Running correct Ford/Holley 91-99 carb. Can't seem to find the sweet spot. Starts quickly and takes throttle fine, but has slight hesitation off idle and seems to run slightly better when I add some choke even after it has warmed up. Could it be that it needs the float raised to increase float bowl volume to increase flow through the main jets? Just installed a new carb kit with new accelerator pump plunger, gaskets, etc. and all passages were blown out with spray carb cleaner to make sure they were open. Don't know what to do about it running better when I apply some choke, so help is certainly appreciated.
|
08-19-2020, 08:06 PM | #2 |
Senior Member
Join Date: Jun 2014
Location: Williamsburg, VA
Posts: 1,627
|
Re: '40 Ford carb fine tuning help needed
What main jet size are you running? You might need to go to the next larger size.
|
Sponsored Links (Register now to hide all advertisements) |
|
08-19-2020, 08:11 PM | #3 |
Senior Member
Join Date: Jun 2010
Location: Detroit suburb, MI
Posts: 3,706
|
Re: '40 Ford carb fine tuning help needed
Check to make sure the accelerator pump is squirting two streams of fuel with the engine off and looking down the throat when opening the throttle. It should squirt with the slightest movement of the throttle. Sometimes there is slop in the pump link from the throttle lever too, which causes a slight delay and possible hesitation.
Sal |
08-19-2020, 09:04 PM | #4 |
Senior Member
Join Date: Dec 2013
Location: Waxahachie, Texas
Posts: 949
|
Re: '40 Ford carb fine tuning help needed
I'm running #50 main jets. What would be the next larger size? Also, I checked that both nozzles are squirting fuel properly and they seem to be OK.
|
08-19-2020, 09:11 PM | #5 | |
Senior Member
Join Date: Sep 2011
Location: Christchurch New Zealand
Posts: 1,611
|
Re: '40 Ford carb fine tuning help needed
Quote:
Phil NZ |
|
08-19-2020, 09:21 PM | #6 |
Senior Member
Join Date: Dec 2013
Location: Waxahachie, Texas
Posts: 949
|
Re: '40 Ford carb fine tuning help needed
Sponsored Links (Register now to hide all advertisements)
|
08-20-2020, 03:07 AM | #7 |
Senior Member
Join Date: May 2010
Location: Oamaru, New Zealand
Posts: 419
|
Re: '40 Ford carb fine tuning help needed
I have always found that when you get the idle real 'sweet', it will often hesitate when you give it some gas, so then I richen the idle mixture a little, and it seems to cure the problem. might work for you.
|
08-20-2020, 12:56 PM | #8 |
Senior Member
Join Date: May 2010
Location: Oshkosh, Wi
Posts: 4,527
|
Re: '40 Ford carb fine tuning help needed
The main jets are not in play at low speed off idle conditions. As noted, try enriching the idle a bit.
|
08-20-2020, 08:36 PM | #9 |
Senior Member
Join Date: Jan 2014
Location: Orcas Island Washington
Posts: 4,932
|
Re: '40 Ford carb fine tuning help needed
I'm sorry, but do the twin idle screws enrichen the mixture when turned clockwise ? I have twisted these two screws for 25 years to get that sweet spot, but still don't get if they control fuel or air.
__________________
Owner/Operator of 'Jailbar Ranch' on the side of Mt. Pickett. Current stable consists of 1946 1/2 ton pickup turned woodie wagon with FH V8, 1947 Tonner Pickup (red) mostly stock with exception of a cummins 6at turbo diesel, 1946 Tonner Pickup (green) with 226 cu in 6 cyl flathead, 1979 Toyota landcruiser wagon, completely encased in 1947 Ford Jailbar sheet metal. Ok, cornbinder rear fenders..... 'Rusty ol' floorboards, hot on their feet' (Alan Jackson) |
08-21-2020, 02:37 AM | #10 | |
Senior Member
Join Date: Jul 2011
Location: SF Bay Area
Posts: 6,645
|
Re: '40 Ford carb fine tuning help needed
Quote:
The idle screws are needle valves. They open counter clockwise on the idle fuel circuit, directly behind the venturi, which sucks the fuel from that circuit. The further they are opened, the faster the idle within the fuel/air optimal ratio, during and after which point the idle speed adjusting screw is adjusted outward, lowering the idle back down by restricting the air intake. This procedure is done individually on the two idle screw valves, repeating until the highest steady vacuum is achieved, all of which is done on a fully warmed up engine. All that said, I've had experts improve on my adjustments just by ear, not bothering with a vacuum gauge at all.
__________________
Alan |
|
08-21-2020, 01:04 PM | #11 |
Senior Member
Join Date: May 2010
Location: Oshkosh, Wi
Posts: 4,527
|
Re: '40 Ford carb fine tuning help needed
They control fuel.
|
|
|
Sponsored Links (Register now to hide all advertisements) |
|