Go Back   The Ford Barn > General Discussion > Model A (1928-31)

Sponsored Links (Register now to hide all advertisements)

Reply
 
Thread Tools Display Modes
Old 01-14-2014, 10:05 AM   #21
1930artdeco
Senior Member
 
1930artdeco's Avatar
 
Join Date: May 2010
Location: Oakland, CA
Posts: 2,763
Default Re: Boring A intake for B carb....

Mr. Chauvin got me to thinking, would just polishing the upper carb, manifold and block ports smooth things out any? I know with more efficiency comes more power or would I just be wasting my time without porting. Just thinking outloud...

Mike
__________________
1930 TownSedan (Briggs)
Still learning after all these years....
1930artdeco is offline   Reply With Quote
Old 01-14-2014, 10:38 AM   #22
H. L. Chauvin
Senior Member
 
Join Date: May 2010
Posts: 4,179
Default Re: Boring A intake for B carb....

Again FWIW, in today's unending varied science of internal combustion engines & unending discussions of same:

1. After performing smoothing out my new Model A intake manifold stated in above paragraph (2.) of above reply no. (10), rather than boring out my new Model A intake manifold with the recommended approximately 1.25" for use with a B carburetor, I experimented using a Dremel tool to open only the bottom end of the intake manifold to approximately 1,25" where it meets the larger Model B carburetor flange & larger Model B carburetor gasket.

2. When looking at this end of the intake manifold opening, near the carburetor, it resembles looking at a Model A or Model B carburetor venturi with an opening that resembles the flare at the end of a trumpet, thus allowing a rapid opening of unobstructed flow from the larger diameter B carburetor into the A manifold.

3. As far as how this particular intake manifold airflow shape & setup works, i.e., to have the fuel/air mix going through that which somewhat resembles a double venturi, one above the carburetor & one inside & below, I honestly have no idea what would be the result if tested to verify results on a dynamometer. I just did it my way.

4. In my opinion, designing internal combustion features are similar to today's empirical design used to make today's gunpowder for rifles & artillery weapons; i. e., make a different batch of gunpowder, shape the shell's internal chamber, then ignite it -- afterwards, "wow" -- check the shell's internal chamber psi and the muzzle velocity with delicate calibrated instruments to observe the results by trial & error -- thus being somewhat similar to internal combustion engine trial & error designs, while using a dynamometer for documenting the varying end results.

5. Today's internal combustion engine design has not yet reached perfection -- like in the 1930's, there will always be room for performance improvement -- just good to share what works & what does not.
H. L. Chauvin is offline   Reply With Quote
Sponsored Links (Register now to hide all advertisements)
Old 01-14-2014, 12:25 PM   #23
Terry,NJ
Senior Member
 
Terry,NJ's Avatar
 
Join Date: Nov 2013
Location: Northern Bucks Co. Pa
Posts: 632
Default Re: Boring A intake for B carb....

Idealy, the manifold would have gentler curves (Larger Radii where the bends are) this would cut down on turbulence of the mixture. Also, the manifold is basically a "T" with the center part (Throat) feeding the two cross arms. I think that 1.250 and Brent's 1.300 are even too small. I was think of welding up a manifold with a 1.500 throat. Next time I run across a broken manifold, I think I will do this. But clearly, The A manifold is a constriction.
Terry
Terry,NJ is offline   Reply With Quote
Reply

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump

Sponsored Links (Register now to hide all advertisements)


All times are GMT -5. The time now is 09:07 PM.