The Ford Barn

johndee138 · 05-02-2014, 12:30 PM

I have a Vintique handle that works right but there isn't any bracing behind the outer sheetmetal so the locking pawl has nothing to engage, and the outer skin deforms inward as you tighten the nut on the end of the shaft. Does any one have an idea how to rig it to work or the correct piece to put inside the lid cavity, of course that would be the preferable fix. The lid latches correctly and stays shut no problem.

Thanks, JM

deuce lover · 05-02-2014, 12:42 PM

I just looked at my 5w deck id and there is factory bracing that angles up from the bottom edge of the lid itself.Then there is a notch that the pawl slides in when in the locked position.Your lid might have been converted from a trunk to a rumble so that bracing would not be there.You might have to take a short piece of tube stock and slide it between the skin of the lid and the latch itself.

oleschool36ford · 05-02-2014, 03:30 PM

If you lid has been converted from trunk to rumble, the bracing should be where the trunk handle hole was located. If the bracing is there, take it out and put at the rumble handle hole.

deuce lover · 05-02-2014, 04:25 PM

Quote:

Originally Posted by oleschool36ford

If you lid has been converted from trunk to rumble, the bracing should be where the trunk handle hole was located. If the bracing is there, take it out and put at the rumble handle hole.

I don't think possible without taking the lid apart as it is between outer and inner skin + spot welded in.

36tbird · 05-02-2014, 05:14 PM

Sponsored Links (Register now to hide all advertisements)

I just made one for a fiberglass rumble lid. Get a piece of sturdy steel flatstock and cut a hole the diameter of the handle flange so it sits down flush. You then file out the square lock notch. I used some flush pop rivets to hold the plate in place. Obviously you need to rivet inside the diameter of the handle's flange.

05-02-2014, 12:30 PM	#1
johndee138 Senior Member Join Date: Jun 2010 Location: Atlanta GA Posts: 505	36 rumble lid lock backer I have a Vintique handle that works right but there isn't any bracing behind the outer sheetmetal so the locking pawl has nothing to engage, and the outer skin deforms inward as you tighten the nut on the end of the shaft. Does any one have an idea how to rig it to work or the correct piece to put inside the lid cavity, of course that would be the preferable fix. The lid latches correctly and stays shut no problem. Thanks, JM

05-02-2014, 12:42 PM	#2
deuce lover Senior Member Join Date: May 2010 Location: Southern France Posts: 5,306	Re: 36 rumble lid lock backer I just looked at my 5w deck id and there is factory bracing that angles up from the bottom edge of the lid itself.Then there is a notch that the pawl slides in when in the locked position.Your lid might have been converted from a trunk to a rumble so that bracing would not be there.You might have to take a short piece of tube stock and slide it between the skin of the lid and the latch itself.

05-02-2014, 03:30 PM	#3
oleschool36ford Senior Member Join Date: May 2010 Posts: 722	Re: 36 rumble lid lock backer If you lid has been converted from trunk to rumble, the bracing should be where the trunk handle hole was located. If the bracing is there, take it out and put at the rumble handle hole.

05-02-2014, 05:14 PM	#5
36tbird Senior Member Join Date: May 2010 Location: nw SanAntonio, TX Posts: 939	Re: 36 rumble lid lock backer Sponsored Links (Register now to hide all advertisements) I just made one for a fiberglass rumble lid. Get a piece of sturdy steel flatstock and cut a hole the diameter of the handle flange so it sits down flush. You then file out the square lock notch. I used some flush pop rivets to hold the plate in place. Obviously you need to rivet inside the diameter of the handle's flange.