1939’ Deluxe 2DR Sedan

[TJ]

Originally Posted by ssffnomad

Ok makes sense , t/y.
So get the Door and Hinge mounted, then clip on springs ?
Stretch

That's how I have done it.

[ssffnomad]

Thanks guys . When converting to 12 Volt. What are you guys using for Dash Gauge Bulbs ?
Stretch

[deuce lover]

#63

[ssffnomad]

T/y

[ssffnomad]

BE47B209-CDFA-45E3-818F-D7EA9D6B1D63.jpg

286C2D0A-2B2F-4E94-A396-910D4F6F82DB.jpg

Good Morn. Could you please help with 39’ Horn Wiring ?
I am guessing that #3 goes to the two horn wires ?
Not sure which is power & ground ?
Stretch

[marko39]

Sponsored Links (Register now to hide all advertisements)

Wires 1&2 are from harness, should be both yellow/green. Yes on #3 to horns. They ground to frame thru their bracket so make sure you have clean surfaces.

[deuce_roadster]

All my early Ford cars have wiring from Chris at Bauer. He will make it any way you want with cloth covered correct colored wire. I told him I was running a 59 series engine in my 32 5w, 6V using generator and v reg, wanted turn signals in the 2 bulb headlights, stock starter switch and headlight switch, 52 Pontiac taillights. Everything came quickly and fit perfect including the dome light wire to switch and on to the light.

[ssffnomad]

Yes Sir, Chris made this 12 Volt cloth harness for our 39’ Deluxe.
Stretch

[ssffnomad]

39’ Deluxe. So new harness was all in , along with new headlight switch. Was working fine, not so much now. Pulled switch off bottom of Steer Box and found a 1/2 clip loose in there.
Does it go on Brass horn connector with the brass spring ? CBA7F2C2-4F7E-4FC0-9711-B48A4D775F8D.jpg

[petehoovie]

Originally Posted by ssffnomad

39’ Deluxe. So new harness was all in , along with new headlight switch. Was working fine, not so much now. Pulled switch off bottom of Steer Box and found a 1/2 clip loose in there.
Does it go on Brass horn connector with the brass spring ? Attachment 493957

[ssffnomad]

As always. Thanks Pete.
Stretch

[38 coupe]

There should be a contact that rotates with the horn rod that is retained by the spring and clip. It can be a bit of a pain to assemble.

[ssffnomad]

Ok so the Contact that rotates on shaft has two blades to go into Headlight Switch. It’s stuck in Switch Housing. I did not want to pull too hard till you guys straightened me out. I will have to pull it out and attach to shaft with clip.
Guess I will also have to clock it properly so “ Deluxe “ is in proper position on steering wheel when Lights are in the “Off” position.

[petehoovie]

Originally Posted by ssffnomad

Ok so the Contact that rotates on shaft has two blades to go into Headlight Switch. It’s stuck in Switch Housing. I did not want to pull too hard till you guys straightened me out. I will have to pull it out and attach to shaft with clip.
Guess I will also have to clock it properly so “ Deluxe “ is in proper position on steering wheel when Lights are in the “Off” position.

[V8COOPMAN]

Originally Posted by ssffnomad

39’ Deluxe. So new harness was all in , along with new headlight switch. Was working fine, not so much now. Pulled switch off bottom of Steer Box and found a 1/2 clip loose in there.
Does it go on Brass horn connector with the brass spring ? Attachment 493957

Here are a couple of different pics/drawing showing where that clip goes. Hope it helps ya. Coop

[ssffnomad]

Well it’s a awesome morning here. Shop doors open . Big Big Heavy Cup of Coffee in hand .
Time to go wrestle with “ Lighting Switch Spider” & “ Lightning Switch Retainer “
Please say Prayers