The Ford Barn

KULTULZ · 03-06-2022, 06:16 AM

Quote:

Originally Posted by 56sedandelivery

Thanks guys. Looks good to go. The #4 drivers side had two shims so will just use the again. The illustration I made up. Thanks again.

One last thing, how tight do you tighten the bolt?

If you made that ILL, you are a man of many talents ...

Below is an ILL of the mounts giving torque values. I do not know the source as Jwahite (1956 SW) included it in one of his earlier posts (2018) describing his ordeal.

56sedandelivery · 03-06-2022, 11:06 AM

[QUOTE=KULTULZ;2110581]If you made that ILL, you are a man of many talents ...

Thanks for the torques specs. Many talents bwaaahahahahaha.

KULTULZ · 03-06-2022, 05:37 PM

OK ... The ILL posted above is a partial scan from the 1955 WSM (NOV 1954 - Pg. 195) so the torque values will be correct (1956 should be the same as JW has a 1956 WSM). I will try to scan the complete ILL and post it.

56sedandelivery · 04-04-2022, 11:47 AM

It is done. Broke the #10 drivers side loose finally. The rest of them went easy. Loosened both sides then removed the drivers side first. Jacked it up and laid on a few 2x4s. Then wire brushed the mounts and installed new pads. Tightened it down to 20 ft pounds and done, I hope.

KULTULZ · 04-04-2022, 12:55 PM

She's going to ride like a CADILLAC ... er ... LINCOLN

miker98038 · 07-01-2022, 09:52 PM

Sponsored Links (Register now to hide all advertisements)

Deleted

PapaDave · 12-30-2023, 07:39 PM

The acetone/ATF combo is the best penetrant I’ve found yet.

03-06-2022, 11:06 AM	#42
56sedandelivery Senior Member Join Date: Mar 2018 Location: Arkansas Posts: 525	Re: Body to Frame Mounts [QUOTE=KULTULZ;2110581]If you made that ILL, you are a man of many talents ... Thanks for the torques specs. Many talents bwaaahahahahaha.

03-06-2022, 05:37 PM	#43
KULTULZ Senior Member Join Date: Aug 2012 Location: IN A 'GALAXIE' FAR FAR AWAY Posts: 6,475	Re: Body to Frame Mounts OK ... The ILL posted above is a partial scan from the 1955 WSM (NOV 1954 - Pg. 195) so the torque values will be correct (1956 should be the same as JW has a 1956 WSM). I will try to scan the complete ILL and post it.

04-04-2022, 12:55 PM	#45
KULTULZ Senior Member Join Date: Aug 2012 Location: IN A 'GALAXIE' FAR FAR AWAY Posts: 6,475	Re: Body to Frame Mounts She's going to ride like a CADILLAC ... er ... LINCOLN __________________ *** - WHY IS IT ... - ... that everything you buy in the grocery store is either wrapped in or contained in plastic but the government doesn't want you to carry it out in a plastic bag? WONDERING IN W(BY GOD)V ... DIAGNOSED CDO** - (OCD In Correct Alphabetical Order)

07-01-2022, 09:52 PM	#46
miker98038 Senior Member Join Date: Mar 2013 Location: Kent, WA. Tucson, AZ Posts: 1,398	Re: Body to Frame Mounts Sponsored Links (Register now to hide all advertisements) Deleted

12-30-2023, 07:39 PM	#47
PapaDave Junior Member Join Date: Dec 2023 Location: Edmonds, WA Posts: 10	Re: Body to Frame Mounts The acetone/ATF combo is the best penetrant I’ve found yet.