|
Sponsored Links (Register now to hide all advertisements) |
|
|
Thread Tools | Display Modes |
01-17-2011, 03:00 PM | #1 |
Senior Member
Join Date: May 2010
Location: Stayton, Oregon
Posts: 3,806
|
Does anyone have measurements for 29 CCPU Kick Panels?
I need to put some kick panels in my 29 CCPU cowl (now a huckster). Does anyone have the measurements or a drawing of these demensions or know where I can find this info? I tried to make a pattern for it out of cardboard but it is very hard to do.
Thanks
__________________
Fred Kroon 1929 Std Coupe 1929 Huckster |
01-17-2011, 03:32 PM | #2 |
Senior Member
Join Date: May 2010
Location: Eastern Tennessee
Posts: 11,516
|
Re: Does anyone have measurements for 29 CCPU Kick Panels?
Don't make them out of cardboard, ...make them out of poster board. Cut p-board into multiple pieces and lay-out the first one that fits the back edge. Then use another one that fits the rise of the subrail extension. Temporarily tape the two together and make some witness marks from one piece to the adjoining piece so you have something to reference to. Next use another straight edge to make the panel that goes up against the firewall and tape that one to the other two. Layout for the curve around the tank and trim. It isn't that difficult and you will have you a pattern in no time at all.
. |
Sponsored Links (Register now to hide all advertisements) |
|
01-17-2011, 04:12 PM | #3 |
Senior Member
Join Date: May 2010
Location: Stayton, Oregon
Posts: 3,806
|
Re: Does anyone have measurements for 29 CCPU Kick Panels?
Thanks Brent. Will give it a try.
__________________
Fred Kroon 1929 Std Coupe 1929 Huckster |
01-17-2011, 08:39 PM | #4 |
Senior Member
Join Date: May 2010
Location: Owls Head
Posts: 257
|
Re: Does anyone have measurements for 29 CCPU Kick Panels?
Send me a private message with a address and I will send you a tracing of an original. The upholstery companies use a thick cardboard with vinal glued to it and it is suppose to be waterproof, but most of the time it warps after a couple of years. There is a construction industry 1/8" thick cardboard material called THERMO PLY that works real well and will not warp, you can glue material to it and you can sew through it.
__________________
Driving old Fords since 1947 |
01-17-2011, 08:46 PM | #5 | |
Senior Member
Join Date: May 2010
Location: Stayton, Oregon
Posts: 3,806
|
Re: Does anyone have measurements for 29 CCPU Kick Panels?
Quote:
__________________
Fred Kroon 1929 Std Coupe 1929 Huckster |
|
01-17-2011, 08:59 PM | #6 |
Senior Member
Join Date: May 2010
Location: Owls Head
Posts: 257
|
Re: Does anyone have measurements for 29 CCPU Kick Panels?
Sponsored Links (Register now to hide all advertisements)
__________________
Driving old Fords since 1947 |
01-18-2011, 12:39 AM | #7 |
Senior Member
Join Date: May 2010
Location: H.B. California
Posts: 451
|
Re: Does anyone have measurements for 29 CCPU Kick Panels?
and post if you can, please.
|
01-18-2011, 01:56 AM | #8 |
Senior Member
Join Date: May 2010
Location: Mpls, MN
Posts: 27,582
|
Re: Does anyone have measurements for 29 CCPU Kick Panels?
Here's 2 pictures of an original mid 28 Tudor kickpad, which would be the same shape as your 29 CCPU. Notice the notch just above the screw in the second picture. Also notice how the binding stopped short of the front edge in the first picture. I'm not sure if they all did this, or if that was the end of the roll. |
01-18-2011, 08:45 AM | #9 |
Senior Member
Join Date: May 2010
Location: va
Posts: 138
|
Re: Does anyone have measurements for 29 CCPU Kick Panels?
the original question was never answered.is there blueprints somewhere for the interior panels of a 1929 ccpu?
|
01-18-2011, 02:01 PM | #10 |
Senior Member
Join Date: May 2010
Location: Owls Head
Posts: 257
|
Re: Does anyone have measurements for 29 CCPU Kick Panels?
I have never measured my 90% there originals, but will give it a shot within a day or so and will post it. Maybe someone out there has the blueprint??
__________________
Driving old Fords since 1947 |
01-18-2011, 02:18 PM | #11 |
Senior Member
Join Date: May 2010
Location: Mpls, MN
Posts: 27,582
|
Re: Does anyone have measurements for 29 CCPU Kick Panels?
It seems to me that Brent gave the best way to make them. For sure they would fit correctly, and with the pictures I posted they can be trimmed correctly with binding.
|
01-18-2011, 02:19 PM | #12 |
Senior Member
Join Date: May 2010
Location: Stayton, Oregon
Posts: 3,806
|
Re: Does anyone have measurements for 29 CCPU Kick Panels?
Thanks guys for the info.
__________________
Fred Kroon 1929 Std Coupe 1929 Huckster |
01-19-2011, 05:37 PM | #13 |
Senior Member
Join Date: May 2010
Location: Owls Head
Posts: 257
|
Re: Does anyone have measurements for 29 CCPU Kick Panels?
This is a test to see if the drawing (crudely done with a tracing, ruler, and several pieces of paper, can be read after a viewer enlarges it. If it works, the bottom of the drawing may be off a little as my original panels that were traced are tattered at the bottom. Also on the short vertical side (engine side) it may or may not be parallel with the door side, it traces at a slight angle as shown in the drawing. If this doesn't work I'll do some brain picking tomorrow and find another way to get a better picture.
__________________
Driving old Fords since 1947 |
01-19-2011, 06:09 PM | #14 |
Senior Member
|
Re: Does anyone have measurements for 29 CCPU Kick Panels?
TJW
Your pic look real good and enlarge good. Thanks for the pic's |
01-20-2011, 01:22 PM | #15 |
Senior Member
Join Date: May 2010
Location: H.B. California
Posts: 451
|
Re: Does anyone have measurements for 29 CCPU Kick Panels?
i intend to use 1/8" clear acrylic when i do this, and paint the inside surface body color, easy to keep clean and remain glossy, durable , no points .
thanks for those specs, tips and images. |
|
|
Sponsored Links (Register now to hide all advertisements) |
|