|
Sponsored Links (Register now to hide all advertisements) |
|
|
Thread Tools | Display Modes |
10-18-2010, 03:31 PM | #1 |
Junior Member
Join Date: May 2010
Location: New Orleans
Posts: 26
|
body blocks 31 S/W Fordor
Anyone else have problems with their body blocks from Brattons. I think the front blocks don't fit and have the holes in the incorrect position, or their pic on their website is wrong. I've tried switching the sides, putting them in backwards, and any other combo I could think of. It seems like I might have to shave off 1/4 - 1/2 inch of the width to get them in there.
Also they only have 3 holes instead of the 4 like they have on their diagram. Scott |
10-18-2010, 06:53 PM | #2 |
Senior Member
Join Date: Jun 2010
Location: (Old)Shasta (Redding) CA
Posts: 385
|
Re: body blocks 31 S/W Fordor
The front mounting blocks for a s/w are different than a other sedans.
Could it be that you have a s/w body on a non-s/w frame. it thats the case only one of the mounting bolts will line up with out moving the mounting flange on the frame. Just my W.A.G. at the problem |
Sponsored Links (Register now to hide all advertisements) |
|
10-18-2010, 08:18 PM | #3 |
Junior Member
Join Date: May 2010
Location: New Orleans
Posts: 26
|
Re: body blocks 31 S/W Fordor
I am trying to put the S/W fordor on an AA chassis. I'm running into problems before I even get that far. The blocks won't fit into the recessed area where the holes are. The recessed floor makes the space too narrow for the block to sit flush in its mounting position.
I'll try and take some picks to show what I mean tomorrow. thanks Scott |
10-19-2010, 07:27 AM | #4 |
Senior Member
Join Date: May 2010
Location: new britain,ct 06052
Posts: 9,390
|
Re: body blocks 31 S/W Fordor
Are not the A and AA frames different? Why would you think blocks from catalog would work without modification? You wil most likely have to modify the blocks you now have or make your own. JMO
Paul in CT |
10-19-2010, 12:13 PM | #5 |
Senior Member
Join Date: May 2010
Location: Denville NJ
Posts: 964
|
Re: body blocks 31 S/W Fordor
Scott, I used the blocks from Brattons a few years ago and they worked out ok. Is there a chance there is something stuck in the slot where the block goes? On a second note, the S/W sedans used an extra mounting flange that is riveted to the outside of the frame. Dose your frame have that? Page 33 of How to restore your Model A vol. 6 has a drawing of the frame and where the blocks go.
__________________
Model A Ford Club of New Jersey http://www.mafcnj.org Model A Pick Up Owners and Enthusiasts http://www.fordbarn.com/forum/group.php?groupid=5 |
10-19-2010, 01:59 PM | #6 |
Senior Member
Join Date: May 2010
Location: Nelson. New Zealand
Posts: 2,009
|
Re: body blocks 31 S/W Fordor
Sponsored Links (Register now to hide all advertisements)
|
10-19-2010, 03:17 PM | #7 |
Senior Member
Join Date: May 2010
Location: Princeton, NJ
Posts: 965
|
Re: body blocks 31 S/W Fordor
Bratton's S/W blocks worked OK for my car. By the "front" blocks, you mean the ones under the windshield pillars, that are hold to the body with a couple of wood screws?
I think for those, I had to carve just a little bit off of the lower front outside corner, to avoid a collision with the bottom lips of the cowl panels. BTW, I did have one other issue: the rear blocks (the big ones) were not quite tall enough. The bottom lip of the wheel well tended to bump into the outer edge of the rear crossmember. I needed to shim them with 1/8" plywood on top. (Or I could have used one extra rubber shim, I guess.) Doug
__________________
My '31 S/W sedan project:http://31ford.dougbraun.com My restoration diary: http://dougbraun.com/blog |
10-19-2010, 06:12 PM | #8 |
Junior Member
Join Date: May 2010
Location: New Orleans
Posts: 26
|
Re: body blocks 31 S/W Fordor
This is my goal
I had this idea and then found a guy on the AA forum that had done it already. This is his truck I know the frame is different, but thought the front mounts were the same. Yes the bracket is on the outside of the frame. I'm not even getting that far though. The body block doesn't fit the body This is a pic of the block from the top, of the passenger side, inside the body for orientation purposes. This is a pic of the problem - when I place the block in its recessed area underneath the body it doesn't fit flush with the floor, while lining up with bolt holes I took a pic from the top while holding the block in the same place and this is what it shows I don't know if you can tell but one of the bolt holes is only about half open and the other is basically misaligned. I tried both front blocks in this manner, flipping them over, flipping them backwards nothing gets them aligned. This is why I was wondering if its the correct block. If its the right block for the 31 S/W body, I'm gonna have to do some trimming of the block to get it to work or make my own. Yes I know I'm going to need to do some serious metal work but I wanted to get some of these block worked out first in order to get the body/doors roughly aligned first, and get a basic mock up done. Scott |
10-20-2010, 08:55 PM | #9 |
Junior Member
Join Date: May 2010
Location: New Orleans
Posts: 26
|
Re: body blocks 31 S/W Fordor
Any other opinions, I'm cutting them up this weekend if not! I hope thats the right answer.
Scott |
02-11-2013, 07:46 PM | #10 |
Senior Member
Join Date: Feb 2012
Location: Yakima, Washington
Posts: 205
|
Re: body blocks 31 S/W Fordor
I want to do something similar...any suggestions. Thanks. Kris
__________________
"The Family Ford" |
|
|
Sponsored Links (Register now to hide all advertisements) |
|