|
Sponsored Links (Register now to hide all advertisements) |
|
|
Thread Tools | Display Modes |
11-19-2016, 05:55 PM | #1 |
Senior Member
Join Date: Nov 2011
Location: Dayton Oregon
Posts: 318
|
29 coup trunk measurments
I need across the top , across the middle , across the bottom an dia. corner to corner, Mine has been smacked at the bottom of the left side in the wheel well so I'm going to have to rebuild the braces and what ever else it takes to get it back to where it belongs. Any help is appreciated.
__________________
Hotrods don't have valve covers |
11-19-2016, 07:59 PM | #2 |
Senior Member
Join Date: Nov 2011
Location: Dayton Oregon
Posts: 318
|
Re: 29 coup trunk measurments
anyone?
__________________
Hotrods don't have valve covers |
Sponsored Links (Register now to hide all advertisements) |
|
11-19-2016, 08:40 PM | #3 |
Senior Member
Join Date: May 2010
Location: South East NJ
Posts: 3,398
|
Re: 29 coup trunk measurments
I found you use the lid and make it all fit.
My cabriolet quarters were messed up. I was thinking I needed to do measurements and such. In practice I found you put the body together and work it all till it fits nice. |
11-19-2016, 09:24 PM | #4 |
Senior Member
Join Date: Nov 2011
Location: Dayton Oregon
Posts: 318
|
Re: 29 coup trunk measurments
if I had a lid that would work
__________________
Hotrods don't have valve covers |
11-19-2016, 11:45 PM | #5 |
Senior Member
Join Date: May 2010
Location: Portland, Oregon
Posts: 5,906
|
Re: 29 coup trunk measurments
I'll get out to the garage tomorrow and get some measurements for you.
__________________
Ray Horton, Portland, OR As you go through life, keep your eye on the donut, not the hole. |
11-20-2016, 01:30 AM | #6 |
Senior Member
Join Date: Nov 2011
Location: Dayton Oregon
Posts: 318
|
Re: 29 coup trunk measurments
Sponsored Links (Register now to hide all advertisements)
__________________
Hotrods don't have valve covers |
11-20-2016, 01:57 AM | #7 |
Senior Member
Join Date: Sep 2010
Location: South Coast NSW Australia
Posts: 2,596
|
Re: 29 coup trunk measurments
You are brave to push and pull a body based on someone else's measurements without a lid to work with first.
Last edited by pooch; 11-20-2016 at 02:05 AM. |
11-20-2016, 02:21 AM | #8 |
BANNED
Join Date: May 2010
Location: Michigan / Ontario border, Sarnia, Ontario. 50 miles from Detroit and 150 from Toronto.
Posts: 5,800
|
Re: 29 coup trunk measurments
|
11-20-2016, 02:32 AM | #9 |
Senior Member
Join Date: Jan 2015
Location: Birkdale, Qld,Aust
Posts: 170
|
Re: 29 coup trunk measurments
3'3/4" at top 3'1/8" middle and 2'11 3/4" at the bottom. Sorry cant get a diagonal with the lid on and I'm not about to take it off.
And +1 to what Pooch said. |
11-20-2016, 12:22 PM | #10 |
Senior Member
Join Date: Nov 2011
Location: Dayton Oregon
Posts: 318
|
Re: 29 coup trunk measurments
I can pull the 36 1/8 in the middle with a ratchet strap from 36 3/4 . it bounces back when let off. time to start unbolting and adjusting to at least get the back bottom panel to bolt up. Thanks for the numbers
__________________
Hotrods don't have valve covers |
11-20-2016, 05:27 PM | #11 |
Senior Member
Join Date: May 2010
Location: Portland, Oregon
Posts: 5,906
|
Re: 29 coup trunk measurments
Since you have the opening measurements, maybe these will also be helpful;
I measured my trunk lid, and here's what I've got: Front to back along the curve of the lid: 30-7/8" Front to back straight from top of the lid to the bottom edge: 28-1/8" Width of deck lid: 35-1/2" Send me a PM or email if you need anything else.
__________________
Ray Horton, Portland, OR As you go through life, keep your eye on the donut, not the hole. Last edited by 700rpm; 11-20-2016 at 08:17 PM. |
11-22-2016, 12:25 AM | #12 |
Senior Member
Join Date: Nov 2011
Location: Dayton Oregon
Posts: 318
|
Re: 29 coup trunk measurments
thanks for the help---I got it real close and borrowed a deck lid from a friend and have close to a 1/4 gap all around----
__________________
Hotrods don't have valve covers |
11-22-2016, 01:25 AM | #13 |
Senior Member
Join Date: May 2010
Location: Portland, Oregon
Posts: 5,906
|
Re: 29 coup trunk measurments
That's about right. My lid is tighter at the top, though; about 1/8".
__________________
Ray Horton, Portland, OR As you go through life, keep your eye on the donut, not the hole. |
|
|
Sponsored Links (Register now to hide all advertisements) |
|