|
Sponsored Links (Register now to hide all advertisements) |
|
|
Thread Tools | Display Modes |
09-16-2015, 11:24 PM | #21 |
Senior Member
Join Date: May 2010
Location: Tucson, Arizona
Posts: 374
|
Re: Installing a Mitchell Overdrive
Pray it does not leak out all the oil you put in the box at the joint between gearbox and rear torque tube as the last two I installed did. Silicone gasket maker sealant can be 100% effective if used correctly however they do not seem to know how to use it.
|
09-17-2015, 01:04 AM | #22 |
Senior Member
Join Date: Apr 2013
Location: West Australia
Posts: 346
|
Re: Installing a Mitchell Overdrive
Thanks to everyone for the great advice and suggestions. I have no doubt that it will assist in making the install easier. Just need to wait the 3 months for delivery of the OD
|
Sponsored Links (Register now to hide all advertisements) |
|
09-17-2015, 07:02 AM | #23 |
Member
Join Date: Jul 2015
Location: Brier, WA
Posts: 82
|
Re: Installing a Mitchell Overdrive
3 month back-up? Hang in there!
Glenn |
09-20-2015, 08:41 AM | #24 |
Senior Member
Join Date: Jan 2012
Location: Ashby, Mass
Posts: 452
|
Re: Installing a Mitchell Overdrive
Is it necessary to remove the springs, and is it easier to install Mitchell with it removed from chassis?
__________________
I know I can, I know I can http://www.flickr.com/photos/waltsprojects/ |
09-21-2015, 01:05 PM | #25 |
Senior Member
Join Date: May 2010
Location: Mpls, MN
Posts: 27,582
|
Re: Installing a Mitchell Overdrive
|
09-27-2015, 09:05 AM | #26 | |
Senior Member
Join Date: May 2010
Location: Jordan, MN
Posts: 1,411
|
Re: Installing a Mitchell Overdrive
Sponsored Links (Register now to hide all advertisements)
Quote:
Good Day! |
|
09-03-2016, 10:52 AM | #27 |
Member
Join Date: Jul 2014
Posts: 59
|
Re: Installing a Mitchell Overdrive
how many man hours to install a mitchell overdrive?
|
09-03-2016, 11:23 AM | #28 |
Senior Member
Join Date: May 2010
Location: brentwood, ca
Posts: 4,241
|
Re: Installing a Mitchell Overdrive
Depends.
Talk to mitchell. Bob |
09-03-2016, 11:55 AM | #29 |
Senior Member
Join Date: Jul 2011
Location: Redondo Beach, CA
Posts: 5,849
|
Re: Installing a Mitchell Overdrive
|
09-03-2016, 01:02 PM | #30 |
Senior Member
Join Date: May 2010
Location: Southern California
Posts: 3,131
|
Re: Installing a Mitchell Overdrive
A little tip when installing a Mitchell overdrive:
The boss where the speedo gear head inserts in the housing is below the oil level in the housing. For this reason do not oil service it until the speedo head is installed. The set screw that holds the speedo head in place will drip oil unless you coat it with some type of sealer before installing. Tom Endy |
08-18-2018, 12:06 PM | #31 |
Junior Member
Join Date: Dec 2016
Posts: 5
|
Re: Installing a Mitchell Overdrive
I just finished installing both a Mitchell Overdrive and transmission in my 1929 model A roadster P/U. Also bought their puller kit which worked great. It was quite a bit of work......however, I love the way the Mitchell transmission shifts. No problem with gears grinding now......wonderful when down shifting.
The overdrive shifts fairly easy but stiff. Goes in to over drive easy but does not shift easily back it to direct drive. Some times I must stop in order to shift back in to direct drive. Slot in floor board has good clearance in both directions. Other than adjusting the shaft length that connects the shift lever to the overdrive......I do not see any other adjustments. Was told the overdrive has syncro's which should allow shifting in and out of overdrive while driving. I have been pushing in the clutch when shifting in/out of overdrive. Any suggestions? Les Von Nordheim |
08-18-2018, 12:24 PM | #32 |
Senior Member
Join Date: May 2016
Location: Scottsdale, Arizona
Posts: 612
|
Re: Installing a Mitchell Overdrive
I would give Mitchell a call...The units usually shift very easily...How does it shift if you are standing still and the engine is not running? Also try shifting it from under the car with the linkage disconnected and see if it makes a difference...It is possible that you have a linkage problem and not an overdrive problem...Ernie in Arizona
|
08-18-2018, 12:44 PM | #33 | |
Senior Member
Join Date: Nov 2016
Location: SoCal
Posts: 877
|
Re: Installing a Mitchell Overdrive
Quote:
When they delivered mine I was told to use 85w-140 GL-5. That seems too thick to me but when it's warmed up after a mile or two, it's just fine, never grinds. I would suggest changing your gear oil in it soon after it's first installed, and after that every 5,000 miles. Don't forget to pull the plugs in the torque tube one in front of the overdrive and the other behind the overdrive box and give it no more than a couple pumps when you change the oil. One of the fittings they give you is close clearance, make sure your rear axle is up on jack stands and park brake released so you can turn the driveshaft to access the grease fittings. I have good results with Ultra Black sealant between the torque tube and differential and a dab of ultra black on the set screw holding the speedometer drive. Tie up the breather tube as high as possible. I have absolutely no leaks. |
|
08-18-2018, 09:35 PM | #34 | |
Senior Member
Join Date: Feb 2015
Location: Lone Jack Missouri
Posts: 381
|
Re: Installing a Mitchell Overdrive
Quote:
Sent from my SM-J700T using Tapatalk |
|
08-18-2018, 10:52 PM | #35 |
Senior Member
Join Date: Sep 2010
Location: Danville, CA
Posts: 1,554
|
Re: Installing a Mitchell Overdrive
Get the best spring spreader you can and leave the spring together with the differential.
Get the best of the two pinion pullers discussed above. I have used both. The good one works, the other one bends. It takes about four hours and is a bit quicker with someone helping you. Two rolling floor jacks are what I use and have done them alone several times, much easier with two guys. Not rocket science, just heavy and I'm not as strong as I was 60 years ago. Be SAFE. I tip the torque tube up and slide the Mitchell down onto the differential. The spring and spring spreader help hold the torque tube up if working alone. This part and aligning the splines with the U-joint are easier with help. The rest is just screwing in nuts and bolts, or unscrewing them. The pinion adjustment is quite simple, I go where I think it is too tight and back it off a tad. I have been told that inch-pound torque wrenches are notoriously inaccurate so I just get the feel of some drag on the pinion and have been happy with those results. Your experience may very. Last edited by daveymc29; 08-18-2018 at 11:01 PM. |
08-18-2018, 11:19 PM | #36 |
Senior Member
Join Date: Dec 2013
Location: No Cal
Posts: 224
|
Re: Installing a Mitchell Overdrive
A tip based on my experience with the Mitchell....
After the new unit is installed you need to pin up the OD vent tube. It's very important this tube always be in a incline from the OD unit. If you let any part of the vent tube sag small amount of oil will Start holding in the sag. On hard pulls the tube just may "burp" This oil out the end of the tube. And if the end of the tube is located Near/above the muffler.... instant smoke screen! I know! Locating this vent tube on the Vicky with the drop floor And keeping it in a inclined position can be challenging... be done for sure. Love the Mitchell. Gil. NoCal |
08-19-2018, 10:47 PM | #37 |
Junior Member
Join Date: Dec 2016
Posts: 5
|
Re: Installing a Mitchell Overdrive
Thanks for the guidance.
I will make a shifting linkage adjustment and see if that helps. Also, I may have not had the overdrive heated up......will do more driving and see if shifting when warmed up is easier. I'm using synthetic gear oil supplied from McMaster Carr 90/140. Also us it in the mitchell transmission. Have used this specific gear oil in my other antique cars with good results. Does not eat up bronze or brass like some other conventional gear oils. I have the breather tube attached under the P/U bed (High) with a loop clamp. Just joined the Model A club of america but have not joined a regional group....have several in our area. Have been a member of the HCCA and Model T ford club of america for many years. Enjoy driving and owning a Model A. Thanks, Les |
|
|
Sponsored Links (Register now to hide all advertisements) |
|