Go Back   The Ford Barn > General Discussion > Model A (1928-31)

Sponsored Links (Register now to hide all advertisements)

Reply
 
Thread Tools Display Modes
Old 10-30-2020, 08:58 AM   #1
KenBolton
Senior Member
 
Join Date: Jun 2020
Location: Fall Creek, WI
Posts: 210
Default Cylinder Soot

Got a surprise when I pulled the plugs to clean the outside of them. Numbers 1 and 2 were very clean however, 3 and 4 were sooty particularly #4. The engine has maybe 3,000 miles on a complete overhaul. I have had to change the exhaust manifold a couple of times but would think if the soot developed due to leaks it would quickly burn off. Also a newly overhauled carb. I tend to run it a bit lean until I get a pop after turning off the ignition then I open the needle valve up a bit. Ideas as to cause of the buildup on 2 cylinders?
KenBolton is offline   Reply With Quote
Old 10-30-2020, 09:21 AM   #2
Big hammer
Senior Member
 
Join Date: Jun 2014
Location: Land of Lincoln
Posts: 3,114
Default Re: Cylinder Soot

I would worry about 1&2 running lean! Then adjust for a rich mixture.
__________________
Don't force it with a little hammer tap, tap, tap
get a bigger hammer tap done
Big hammer is offline   Reply With Quote
Sponsored Links (Register now to hide all advertisements)
Old 10-30-2020, 09:37 AM   #3
Will N
Senior Member
 
Will N's Avatar
 
Join Date: Jul 2010
Location: Pennsylvania
Posts: 1,096
Default Re: Cylinder Soot

Could be the intake manifold is not seating well around the cylinder 1 and 2 port, and you're getting a vacuum leak, leaning out those two cylinders. You compensate by opening up the GAV, enriching the mixture to get rid of the pop, but now 3 and 4 are running too rich. I'd recommend having the manifolds machined as a unit to make sure they are flat.
Will N is offline   Reply With Quote
Old 10-30-2020, 11:07 AM   #4
30 Closed Cab PU
Senior Member
 
Join Date: Aug 2018
Posts: 2,332
Default Re: Cylinder Soot

I do not know your experience level on As, so excuse me if you already know this info.

When reading the plug only go by what the ceramic insulator looks like. It is not uncommon for the rest of the plug to be black/slightly sooty. Look for a nice tan color, clean/pure white is too lean, black/sooty is too rich. When I first got my truck, had difficulty believing it was OK to have black and soot on the plugs with a tan insulator - was too used to modern cars, especially cars with electronic ignition and fuel injection.

Perhaps post a picture of your Plugs?

Last edited by 30 Closed Cab PU; 10-30-2020 at 11:08 AM. Reason: sp
30 Closed Cab PU is offline   Reply With Quote
Old 10-30-2020, 11:24 AM   #5
rfitzpatrick
Senior Member
 
Join Date: May 2018
Location: Coral Springs, Florida
Posts: 547
Default Re: Cylinder Soot

[QUOTE=30 Closed Cab PU;1946937]I do not know your experience level on As, so excuse me if you already know this info.

" Look for a nice tan color, clean/pure white is too lean, black/sooty is too rich. "






Well I'll be darn -- Thanks
rfitzpatrick is offline   Reply With Quote
Old 10-30-2020, 05:15 PM   #6
[email protected]
Senior Member
 
modela@aol.com's Avatar
 
Join Date: Aug 2011
Location: Illinois
Posts: 730
Default Re: Cylinder Soot

Sponsored Links (Register now to hide all advertisements)
What brand spark plugs are in use? All with the correct gap? The correct heat range type of plug? Do a compression check on all cylinders to see if they are all close to each other.

spark-plug-reader-chart.jpg
modela@aol.com is offline   Reply With Quote
Reply

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump

Sponsored Links (Register now to hide all advertisements)


All times are GMT -5. The time now is 09:51 AM.