Go Back   The Ford Barn > General Discussion > Early V8 (1932-53)

Sponsored Links (Register now to hide all advertisements)

Reply
 
Thread Tools Display Modes
Old 10-23-2020, 06:26 PM   #1
Yoyodyne
Senior Member
 
Yoyodyne's Avatar
 
Join Date: Nov 2010
Location: Lancaster PA
Posts: 527
Default L-100 cam in a 221

I've been forced to rethink the motor I've been building and will start over with a 36LB block with maybe .030 overbore and stock stroke. I'll be using stock 36 aluminum heads. I plan to optimize the CR with .040 piston to head clearance and milling the heads. I have a Fenton 2 carb manifold and 2 Holley 94s. I also have an L-100 cam.



I've had other engines with a lot of cam and not a lot of compression, revving something to make it work is not a new experience, I don't need a torque monster to have fun. This is going into a 36 pickup with 3.78 gears and a stock 39 trans, just for occasional local fun.


Will this cam work OK in a 221?


Would porting the block be important in this combination?
Yoyodyne is offline   Reply With Quote
Old 10-23-2020, 06:33 PM   #2
Ol' Ron
Senior Member
 
Ol' Ron's Avatar
 
Join Date: May 2010
Location: Chester Vt
Posts: 8,841
Default Re: L-100 cam in a 221

I've probably built more engines than anyone else with the L-100, it was the goto cam. However they didn't run well in a small engine especially in a heavy vehicle . But they do sound good. Why not the 1007b, sounds good and would probably run better.
Ol' Ron is offline   Reply With Quote
Sponsored Links (Register now to hide all advertisements)
Old 10-23-2020, 06:47 PM   #3
Brian
Senior Member
 
Brian's Avatar
 
Join Date: May 2010
Location: Masterton, New Zealand
Posts: 3,816
Default Re: L-100 cam in a 221

Yoyo, I've built and run numerous 221's, including the L100 and Fenton twin as you're proposing. I agree with Ron; the L100 is not a good cam in this application. Try an Isky 88 cam along with your other mods, take the lip off the flywheel, use a 9" clutch, and yes, port the block. The idea is to lighten everything as much as possible and allow the thing to breathe. Enjoy...
__________________
Unfortunately, two half wits don't make a whole wit!
Brian is offline   Reply With Quote
Old 10-23-2020, 07:20 PM   #4
Bored&Stroked
Senior Member
 
Bored&Stroked's Avatar
 
Join Date: Jan 2011
Location: Central Ohio
Posts: 5,011
Default Re: L-100 cam in a 221

Quote:
Originally Posted by Ol' Ron View Post
I've probably built more engines than anyone else with the L-100, it was the goto cam. However they didn't run well in a small engine especially in a heavy vehicle . But they do sound good. Why not the 1007b, sounds good and would probably run better.
This would be my choice in cams . . . but there are plenty of ways to "skin this cat".
Bored&Stroked is online now   Reply With Quote
Old 10-23-2020, 07:55 PM   #5
Yoyodyne
Senior Member
 
Yoyodyne's Avatar
 
Join Date: Nov 2010
Location: Lancaster PA
Posts: 527
Default Re: L-100 cam in a 221

Thanks for the knowledgeable recommendations! A quick search shows isky cams only for 42-up, would I have to give up the 3 bolt distributor and front plate?
Yoyodyne is offline   Reply With Quote
Old 10-23-2020, 08:12 PM   #6
Brian
Senior Member
 
Brian's Avatar
 
Join Date: May 2010
Location: Masterton, New Zealand
Posts: 3,816
Default Re: L-100 cam in a 221

Sponsored Links (Register now to hide all advertisements)
Just use your stock cam and get it ground by one of 'our' camgrinders on here....
__________________
Unfortunately, two half wits don't make a whole wit!
Brian is offline   Reply With Quote
Old 10-23-2020, 09:48 PM   #7
Ol' Ron
Senior Member
 
Ol' Ron's Avatar
 
Join Date: May 2010
Location: Chester Vt
Posts: 8,841
Default Re: L-100 cam in a 221

The L 100 need compression and cubs to build the torque lost to a long cam. Thus you have a streetable cay. The 276 does this.
Ol' Ron is offline   Reply With Quote
Old 10-24-2020, 07:29 AM   #8
Bored&Stroked
Senior Member
 
Bored&Stroked's Avatar
 
Join Date: Jan 2011
Location: Central Ohio
Posts: 5,011
Default Re: L-100 cam in a 221

Quote:
Originally Posted by Yoyodyne View Post
Thanks for the knowledgeable recommendations! A quick search shows isky cams only for 42-up, would I have to give up the 3 bolt distributor and front plate?
I've had Pete grind some 1007B profiles (and a lot of others) - he does extremely nice work. Also Kiwi Tony grinds a lot of cams and is highly respected on the Ford Barn world (though I don't know what masters he has).

Truth be told, I'd rather have a stock cam reground these days than buy a "new" one. But hey, that is just me . . .
Bored&Stroked is online now   Reply With Quote
Old 10-24-2020, 04:29 PM   #9
Pete
Senior Member
 
Pete's Avatar
 
Join Date: May 2010
Location: Wa.
Posts: 5,373
Default Re: L-100 cam in a 221

Quote:
Originally Posted by Bored&Stroked View Post
Truth be told, I'd rather have a stock cam reground these days than buy a "new" one. But hey, that is just me . . .
Just for the book, I won't put a race grind on an after market cast core.
The heat treat is really bad. (inconsistent)
Pete is offline   Reply With Quote
Old 10-24-2020, 04:48 PM   #10
Tim Ayers
Senior Member
 
Join Date: May 2010
Location: NJ
Posts: 6,142
Default Re: L-100 cam in a 221

Quote:
Originally Posted by Pete View Post
Just for the book, I won't put a race grind on an after market cast core.
The heat treat is really bad. (inconsistent)
Meaning, using a stock Ford camshaft for regrinds, right?
Tim Ayers is offline   Reply With Quote
Old 10-24-2020, 05:19 PM   #11
Brian
Senior Member
 
Brian's Avatar
 
Join Date: May 2010
Location: Masterton, New Zealand
Posts: 3,816
Default Re: L-100 cam in a 221

I always use a steel camshaft out of an early engine...
__________________
Unfortunately, two half wits don't make a whole wit!
Brian is offline   Reply With Quote
Old 10-24-2020, 05:47 PM   #12
Pete
Senior Member
 
Pete's Avatar
 
Join Date: May 2010
Location: Wa.
Posts: 5,373
Default Re: L-100 cam in a 221

Quote:
Originally Posted by Tim Ayers View Post
Meaning, using a stock Ford camshaft for regrinds, right?
Yup.
Pete is offline   Reply With Quote
Old 10-24-2020, 07:10 PM   #13
Yoyodyne
Senior Member
 
Yoyodyne's Avatar
 
Join Date: Nov 2010
Location: Lancaster PA
Posts: 527
Default Re: L-100 cam in a 221

Since Pete is here, what is the acceptable smallest diameter for cam journals to reuse? I checked the 3 I have, they range between 1.7955/1.797.


What do (or should) installed cam bearings measure?
Yoyodyne is offline   Reply With Quote
Old 10-24-2020, 07:40 PM   #14
Brian
Senior Member
 
Brian's Avatar
 
Join Date: May 2010
Location: Masterton, New Zealand
Posts: 3,816
Default Re: L-100 cam in a 221

Cam journals measure between 1.796-1.797". Wear limit is 1.795" Clearance in brgs is .002"
this is what i do; Install .010" undersize cam bearings. Measure the installed dia of each bearing. As a reground cam is ground between centres, I put the camshaft between the same centres and grind the journals to suit the installed bearings. Do not assume that .010" bearings, when installed will measure exactly .010 u/s! Doing it this way ensures perfect concentricity of the camshaft journals and lobes, also, I am assured the correct clearances are in place, with no resultant loss of oil pressure through sloppy clearances.
__________________
Unfortunately, two half wits don't make a whole wit!
Brian is offline   Reply With Quote
Old 10-24-2020, 08:18 PM   #15
Ol' Ron
Senior Member
 
Ol' Ron's Avatar
 
Join Date: May 2010
Location: Chester Vt
Posts: 8,841
Default Re: L-100 cam in a 221

Where do you get under size cam bearings.??
Gramps
Ol' Ron is offline   Reply With Quote
Old 10-24-2020, 08:39 PM   #16
Brian
Senior Member
 
Brian's Avatar
 
Join Date: May 2010
Location: Masterton, New Zealand
Posts: 3,816
Default Re: L-100 cam in a 221

They are out there....
__________________
Unfortunately, two half wits don't make a whole wit!
Brian is offline   Reply With Quote
Old 10-24-2020, 08:48 PM   #17
Pete
Senior Member
 
Pete's Avatar
 
Join Date: May 2010
Location: Wa.
Posts: 5,373
Default Re: L-100 cam in a 221

Quote:
Originally Posted by Yoyodyne View Post
Since Pete is here, what is the acceptable smallest diameter for cam journals to reuse? I checked the 3 I have, they range between 1.7955/1.797.


What do (or should) installed cam bearings measure?
For clearance, I run .002 on street engines and .003 on race engines.

I use 1.795 as a minimum as long as it is round.
Pete is offline   Reply With Quote
Old 10-24-2020, 08:53 PM   #18
Pete
Senior Member
 
Pete's Avatar
 
Join Date: May 2010
Location: Wa.
Posts: 5,373
Default Re: L-100 cam in a 221

Quote:
Originally Posted by Ol' Ron View Post
Where do you get under size cam bearings.??
Gramps
H&H may have them.
Pete is offline   Reply With Quote
Old 10-25-2020, 12:17 AM   #19
Yoyodyne
Senior Member
 
Yoyodyne's Avatar
 
Join Date: Nov 2010
Location: Lancaster PA
Posts: 527
Default Re: L-100 cam in a 221

Quote:
Originally Posted by Ol' Ron View Post
Where do you get under size cam bearings.??
Gramps

Most of the new parts sellers have them, they are currently made. I have a set I don't need now.



Quote:
Originally Posted by Brian View Post
Cam journals measure between 1.796-1.797". Wear limit is 1.795" Clearance in brgs is .002"
this is what i do; Install .010" undersize cam bearings. Measure the installed dia of each bearing. As a reground cam is ground between centres, I put the camshaft between the same centres and grind the journals to suit the installed bearings. Do not assume that .010" bearings, when installed will measure exactly .010 u/s! Doing it this way ensures perfect concentricity of the camshaft journals and lobes, also, I am assured the correct clearances are in place, with no resultant loss of oil pressure through sloppy clearances.
I had Dave Generous grind my L-100. The only usable core I had at the time was worn undersize and needed the journals ground. Dave said he couldn't do it on his grinder, he wanted me to send it elsewhere first to have that done before he ground the lobes. That's when I bought this set of .010 bearings. I found a the cores I have in parts engines since then while looking for a good block.
Yoyodyne is offline   Reply With Quote
Reply

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump

Sponsored Links (Register now to hide all advertisements)


All times are GMT -5. The time now is 11:38 AM.