|
Sponsored Links (Register now to hide all advertisements) |
|
|
Thread Tools | Display Modes |
09-20-2018, 03:59 PM | #1 |
Senior Member
Join Date: May 2010
Location: Southern Upstate New York
Posts: 1,160
|
Toe-in Alignment tool
One of our older club members has one of those spring loaded toe-in gauge tools that has the small chains at each of the pointed ends. I don't know the manufacturer's name or model number. I am looking to find an instruction sheet for the use of this tool. Several other club members have tried to use this tool and they can't get repeatable readings with it. I tried the tool on my 30 CCPU which has had the front suspension and steering serviced and my readings are very repeatable. There seems to be a problem with the procedure and how to get the correct reading. Can anyone help clear this up????
__________________
AL in NY |
09-20-2018, 04:20 PM | #2 |
Senior Member
Join Date: May 2010
Location: Largo Florida
Posts: 7,225
|
Re: Toe-in Alignment tool
I think those gauges work pretty good. I'm wondering if there is an issue with the gauge such as rust, stickiness or a problem with the vehicle its used on. It doesn't take much to get a strange reading.
|
Sponsored Links (Register now to hide all advertisements) |
|
09-20-2018, 04:32 PM | #3 |
Senior Member
Join Date: May 2010
Location: So Cal
Posts: 8,749
|
Re: Toe-in Alignment tool
Here's a link to information on Marco's site. http://www.abarnyard.com/workshop/align.htm
|
09-20-2018, 04:41 PM | #4 |
Senior Member
|
Re: Toe-in Alignment tool
They work pretty good.
Car on flat driveway. Roll car back about a car length, then back where you started. Put tool in front of axle and at the height that lets the chains just touch the surface. Position the tool ends at the innermost side of the tire. Zero the gage. Roll the car forward until the chains just touch the surface rearward of the axle. Carefully read the gage. Repeat this, but be sure to roll the car back and forth like when you started. You have to normalize the suspension and steering system before you measure again. Good luck |
09-20-2018, 05:55 PM | #5 |
Senior Member
Join Date: Mar 2013
Location: Hudson, NY
Posts: 511
|
Re: Toe-in Alignment tool
I have one of these and tried it... The problem is that when the gauge is to the back of the car, you have to crawl under to read the gauge. If I do it backwards, that is, end with the gauge to the front, will it read toe-out...
|
09-20-2018, 07:11 PM | #6 |
Senior Member
Join Date: Dec 2010
Location: FRESNO, CA
Posts: 12,560
|
Re: Toe-in Alignment tool
Sponsored Links (Register now to hide all advertisements)
Bill W.
__________________
"THE ASSISTANT GURU OF STUFF" |
09-20-2018, 07:16 PM | #7 |
Senior Member
Join Date: Mar 2017
Location: Connecticut Shoreline
Posts: 1,823
|
Re: Toe-in Alignment tool
Front end shop, $49.95.
Today they make some really nice equipment. Had our 29 done two years ago along with a complete grease job with high pressure grease gun. Made a big difference. Drives like it has power steering, and tracks right down the road straight. |
09-21-2018, 05:53 AM | #8 | |
Senior Member
Join Date: May 2010
Location: Mpls, MN
Posts: 27,582
|
Re: Toe-in Alignment tool
Quote:
|
|
09-21-2018, 09:05 AM | #9 |
Senior Member
Join Date: Jan 2016
Posts: 2,097
|
Re: Toe-in Alignment tool
I bought a stickie tape from Hobby Lobby for $2.39 and a shower curtain from Wallmart for about $10.
This solved a death wobble that I had. |
09-21-2018, 09:36 AM | #10 |
Senior Member
Join Date: Mar 2017
Location: Connecticut Shoreline
Posts: 1,823
|
Re: Toe-in Alignment tool
You guys are kiddy “right”.
Tape measures and shower curtains? Do you really think there were not front end machines back in the day? We read all the time on this forum about shimmy and death wobble. There are other people out there, on the road, also driving with us. Model A’s are not toys. People can get killed if a car or truck is not maintained properly. There are a lot of very well maintained antique cars on the roads that are as safe today as the day they were made. There are also a lot of unsafe poorly maintained cars. My belief is to fix it right, or do not drive it until it can be fixed. Sorry if my soap box has caused anyone heartburn. |
09-21-2018, 09:37 AM | #11 |
Senior Member
Join Date: Oct 2014
Location: Charlotte, NC
Posts: 310
|
Re: Toe-in Alignment tool
I bought one and it works great. I too figured out you can use a shower curtain, put chains on it, then just mark with a pencil where the two rods come together and then roll it forward and mark again, take it off and see what the measurement is between the two marks....works great and shower curtain rods are cheap
|
09-21-2018, 10:43 AM | #12 |
Senior Member
Join Date: May 2010
Location: So Minn
Posts: 1,565
|
Re: Toe-in Alignment tool
The pins in the tread method and the shower curtain rod with pencil marks method are the two best ideas. And also the simplest ones. That just can't be right!
|
09-21-2018, 01:41 PM | #13 |
Senior Member
Join Date: May 2010
Location: Southern Upstate New York
Posts: 1,160
|
Re: Toe-in Alignment tool
Thanks for all the input guys. I believe I did my car correctly. Don't know why the other members had a problem with this tool. Maybe I'll give them a copy of the instruction sheet and they can try again.
__________________
AL in NY |
09-21-2018, 02:24 PM | #14 |
Senior Member
|
Re: Toe-in Alignment tool
You will need rims that are true and have no wobble to be successful. Otherwise, you can get a false reading. I always find it best to use a marker that is stationary on the floor. Spin the tire with the marker against the tire. This will give you a true center line on the tire. Using the lines to measure the distance will give you a true reading to work with. Remember, if the rim is out 1/4 inch from true, you will not get an accurate reading.
|
09-21-2018, 03:21 PM | #15 |
Senior Member
Join Date: May 2010
Location: Southern Upstate New York
Posts: 1,160
|
Re: Toe-in Alignment tool
Dick M, the wobble in the rim does not make a difference in the measurement. If you pick one point anywhere on the tire, it will rotate in a circle perpendicular to the axis of rotation, providing there is no play into the wheel bearings. You will have to re-zero the tool if you move it to another point on the tire if your wheesl don't run true, but the toe-in final measurement will be the same.
__________________
AL in NY |
09-21-2018, 03:27 PM | #16 | |
Senior Member
Join Date: May 2010
Location: Tacoma, WA
Posts: 1,025
|
Re: Toe-in Alignment tool
Quote:
|
|
09-21-2018, 06:42 PM | #17 |
Senior Member
Join Date: May 2010
Location: Epping N.H.
Posts: 2,987
|
Re: Toe-in Alignment tool
Even if you have a little play in the wheel bearings,you will be OK.You have the weight of the car holding them tight.I have a Duby bar,and really find a spring loaded shower bar to be easier.It is too hard to read those numbers through the slotted window.There was a fellow on here years ago that was setting his toe-in perfect in the garage.When he backed it out he see how far it was out with his eyes.It took a while for everybody trying to help him to figure out he was setting it with the car jacked up with the wheels hanging.When I worked in a Mack garage we set toe in with a tape measure,as per the Mack manual.
|
09-21-2018, 10:27 PM | #18 |
Senior Member
Join Date: Dec 2010
Location: FRESNO, CA
Posts: 12,560
|
Re: Toe-in Alignment tool
REMEMBER, LOOSEY GOOSEY adjusted front wheel bearings can FOIL your toe in adjustment!
The STRANGE ways some Folks adjust their bearings, are plain old SCAREY!! One Guy just ran the nuts, FINGER TIGHT!!!! Some backed them off by 1 or 2 castelations!!!! SCAREY!!! Some even used chassis grease, in the bearings!!! Don't know what color it was???? Bill Slight pre-load[/B]
__________________
"THE ASSISTANT GURU OF STUFF" |
03-14-2019, 05:12 PM | #19 |
Senior Member
Join Date: Feb 2012
Location: Gardnerville, Nevada
Posts: 101
|
Re: Toe-in Alignment tool
I have used the "Tenhulzen" Toe Plates on several cars with good results. Summit Racing and Amazon carries the Tenhulzen 2200 toe plates.
The tool uses the wheel rim for measurements so the rim has to run true. check out the video at Summit racing for this item. The tool consists of two plates and two tape measures. Cost is $100. at most sites. Last edited by nevadavic; 03-25-2019 at 12:00 PM. Reason: Spelling |
03-14-2019, 06:42 PM | #20 | |
Senior Member
Join Date: Mar 2013
Location: Bend Or.
Posts: 1,056
|
Re: Toe-in Alignment tool
Quote:
__________________
Bill Worden 1929 Roadster 1929 Briggs Town Sedan 1930 Closed Cab pickup Smith Motor Compressor 1951 Ford F1 High Desert Model A's |
|
03-14-2019, 10:42 PM | #21 | |
Senior Member
Join Date: Apr 2016
Location: St Clair, Michigan
Posts: 395
|
Re: Toe-in Alignment tool
Quote:
I use the red Lucas thick stuff.
__________________
Isaiah B. 1928 all metal Tudor |
|
03-15-2019, 08:01 AM | #22 | |
Senior Member
Join Date: Jan 2016
Posts: 2,097
|
Re: Toe-in Alignment tool
Quote:
The shower curtain route is an exact copy of an original. This allows me to do the job at home, not have to bring it to a garage, do it for free. I have loaned out my "shower curtain" to 4 others and they are happy with the results. After I do the alignment I then can install the tool in my bathroom and have shower. This is truly a dual purpose, multi-functional tool. |
|
Sponsored Links (Register now to hide all advertisements) |
|
03-15-2019, 08:36 AM | #23 |
Senior Member
Join Date: May 2010
Location: Williamsburg, VA
Posts: 510
|
Re: Toe-in Alignment tool
https://wheel-a-matic.com/cars-light...-gauge-inches/
Check around online as prices vary dramaticaly. Bought a NOS on Ebay for $30. |
03-15-2019, 10:02 AM | #24 |
Senior Member
Join Date: Apr 2018
Location: Mebane NC
Posts: 2,353
|
Re: Toe-in Alignment tool
I'd be remiss not to mention this excellent post from 2014:
https://www.fordbarn.com/forum/showp...3&postcount=16 Measuring your toe-in is one thing, but then how do you know how much to rotate the tie rod? This post gives the exact math to calculate it. I used it last weekend when I did my toe-in and the results came out perfectly. For the record, I measured toe-in by jacking up the front end, marking horizontally across each tire with chalk, and then measuring the distance for that point at a consistent height in the front and the back. To improve accuracy, I measured the distance between 3 points at the edges of the tread grooves on each tire and then averaged the results. |
03-15-2019, 10:19 AM | #25 | ||
Senior Member
Join Date: Jun 2015
Location: Red Deer, Alberta
Posts: 5,043
|
Re: Toe-in Alignment tool
Quote:
Quote:
__________________
If you don't hear a rumor by 10 AM, start one!. Got my education out behind the barn! |
||
03-16-2019, 08:35 AM | #26 |
Senior Member
Join Date: May 2010
Location: Reseda, Calif.
Posts: 2,188
|
Re: Toe-in Alignment tool
Sponsored Links (Register now to hide all advertisements)
|
03-16-2019, 11:00 AM | #27 |
Senior Member
Join Date: Dec 2016
Location: Sunrise Beach, Mo
Posts: 439
|
Re: Toe-in Alignment tool
I fear I did overkill on this toe in thing, but, it is what it is! I got some angle iron from my junk pile and some wood. I then cut the angle iron in two pieces that when held up next to my model a tires, there was an inch sticking out front and back. Next, I cut two pieces of wood, and formed the wood to fit just inside the rim lip! I then bolted the wood in line with the edge of the angle iron and screwed the wood to the angle iron! I then cut another hunk of angle to fit on the inside of the Wheel and drilled holes in both the outside piece with the wood attached and took some thread stock and mounted two sets of these on each front wheel. Using a level, got both mounted to be perfectly level and at the same height. Then using a ruler, I did my toe in measure and adjustment! The order of things, is adjust wheel bearings, then do toe in, and sadly with my homemade arrangement, since you should do toe in averaging because wheels are not true, I had to reclamp and level and measure about 3 times! But when done, no more shimmy!
|
03-16-2019, 06:11 PM | #28 | |
Senior Member
Join Date: Jan 2016
Posts: 2,097
|
Re: Toe-in Alignment tool
Quote:
A example would be you have 7 and 1/2 to start. You roll the car and end up with 7 and 5/8. Now you turn the tie rod back to 7 and 9/16. |
|
03-20-2019, 08:08 PM | #29 |
Senior Member
Join Date: Mar 2012
Location: Addison,ll.
Posts: 454
|
Re: Toe-in Alignment tool
Here are original instructions for the Duby Toe In gage.
|
03-20-2019, 08:13 PM | #30 |
Senior Member
Join Date: Mar 2012
Location: Addison,ll.
Posts: 454
|
Re: Toe-in Alignment tool
I recommend when using the Duby gage, try doing it on at least 2 different places on tires just to confirm your results.
|
03-20-2019, 10:25 PM | #31 |
Senior Member
Join Date: Nov 2018
Location: Farmington MI
Posts: 284
|
Re: Toe-in Alignment tool
I like the four Texaco oil can idea... which brings up the question, how high off the ground do you measure the 1/16 inch or whatever the measure should be? Higher up will give a larger measure until you get to the wheel center line. In other words how long are those chains on the commercial tool?
Joe B |
03-21-2019, 03:05 PM | #32 |
Senior Member
Join Date: May 2010
Location: Southern Upstate New York
Posts: 1,160
|
Re: Toe-in Alignment tool
JoeCB, you don't raise the front end up off the ground to do this alignment procedure. The chains on the tool are a reference as to how high off the ground the tool is placed on the tire. Place the tool on the tire so the chains just touch the ground. Zero the measurement on the tool. Then roll the car forward until the chains again are just touching the ground. Look at the gauge measurement on the tool. It will tell you the amount of toe-in or toe-out your car has.
__________________
AL in NY |
03-21-2019, 04:43 PM | #33 |
Senior Member
Join Date: Jan 2019
Location: Germany, near Aachen
Posts: 1,157
|
Re: Toe-in Alignment tool
My question too: How long must the chains be?
__________________
Beste Gruesse aus Deutschland, Werner Ford Model A, Roadster, 1928 Citroen 11 CV, 1947 Hercules W 2000, 1976; (with NSU-Wankel Rotary Engine), Canadian version |
03-21-2019, 05:27 PM | #34 |
Senior Member
Join Date: May 2010
Location: Southern Upstate New York
Posts: 1,160
|
Re: Toe-in Alignment tool
I don't have a tool to look at, but my best estimate would be 10 inches.
__________________
AL in NY |
03-21-2019, 07:36 PM | #35 |
Senior Member
Join Date: Nov 2018
Location: Farmington MI
Posts: 284
|
Re: Toe-in Alignment tool
Yes, that is what I'm looking for … the length of the chains? Because the height off the ground of the tool ( not the car) will change the measured toe in. If one is to set toe in to a specification then you have to know how high (off the ground) to take the measurement.
Joe B |
03-22-2019, 07:14 AM | #36 |
Senior Member
Join Date: Mar 2013
Location: Hudson, NY
Posts: 511
|
Re: Toe-in Alignment tool
I'll measure my chains and report back later today...
Frank |
03-22-2019, 08:20 AM | #37 |
Senior Member
Join Date: Jan 2016
Posts: 2,097
|
Re: Toe-in Alignment tool
My curtain rod chains are 6 inches. I read somewhere it should be 6 inches.
|
03-22-2019, 03:33 PM | #38 |
Senior Member
Join Date: Jul 2010
Location: Auckland, New Zealand
Posts: 514
|
Re: Toe-in Alignment tool
The chains cannot be longer than the height of the front wishbone arms from the floor. Otherwise the wishbone will knock the trammel off the tyres as you roll the car forward and the trammel rises up to meet the wishbone. 6 inches sounds about right. It is defined in the Ford service bulletins, where the toe in figure is specified as being measured well below hub height by Ford.
I am not in a place where I can look it up tight now. Somewhere on the Barn recently the Ford service method was reproduced. SAJ in NZ |
03-22-2019, 04:50 PM | #39 |
Senior Member
Join Date: Mar 2013
Location: Hudson, NY
Posts: 511
|
Re: Toe-in Alignment tool
My Duby Gauge has chains that are 7 1/2" long.
Frank |
03-22-2019, 08:09 PM | #40 |
Senior Member
Join Date: Nov 2018
Location: Farmington MI
Posts: 284
|
Re: Toe-in Alignment tool
Well this conversation explains a lot... Thanks all. Not knowing the correct procedure I had always checked my toe-in at hub level using the taught string 4 - wheel alignment procedure. Measuring that high off the ground I will be getting way less toe- in than the spec. Might help explain tendency to wander.
Joe B |
03-24-2019, 07:09 PM | #41 | |
Senior Member
Join Date: May 2010
Location: Between Seattle & Tacoma
Posts: 2,354
|
Re: Toe-in Alignment tool
Quote:
|
|
03-24-2019, 07:12 PM | #42 |
Senior Member
Join Date: May 2010
Location: Between Seattle & Tacoma
Posts: 2,354
|
Re: Toe-in Alignment tool
|
Sponsored Links (Register now to hide all advertisements) |
|
03-25-2019, 07:53 AM | #43 |
Senior Member
Join Date: Nov 2010
Location: Beamsville,Ontario,Canada
Posts: 482
|
Re: Toe-in Alignment tool
|
|
|
Sponsored Links (Register now to hide all advertisements) |
|