Go Back   The Ford Barn > General Discussion > Early V8 (1932-53)

Sponsored Links (Register now to hide all advertisements)

Reply
 
Thread Tools Display Modes
Old 04-30-2017, 05:03 PM   #1
pooch
Senior Member
 
pooch's Avatar
 
Join Date: Sep 2010
Location: South Coast NSW Australia
Posts: 2,596
Default 239 bore.

If a standard piston is 3.185, what is the optimum bore size at bottom of cylinder ?

How much wear at bottom and how much taper is allowable at top of bore for just a reasonable runnning engine that will never see a lot of miles.

ie, fitting new pistons into an existing bore.
pooch is offline   Reply With Quote
Old 04-30-2017, 05:40 PM   #2
JSeery
Member Emeritus
 
JSeery's Avatar
 
Join Date: Nov 2012
Location: Wichita KS
Posts: 16,132
Default Re: 239 bore.

I don't know the specs off the top of my head, but there are several things to consider. Taper, how egg shaped/out of round the bore is, ridge at top of the cylinder, etc. Ridge must be removed or there is a good chance of breaking the top ring.

Per Repair Manual, Ford, Mercury & Truck, V8 Engines, 1937 to 1947, Ford Motor Company, July 7, 1947:

Ware limits

Bore out of round - .003 max
Bore taper - .006 max
Bore ware - .006 max
Piston to bore - .005 thickness gauge 1/2 wide 6 to 10 lbs pull

Last edited by JSeery; 04-30-2017 at 07:04 PM.
JSeery is offline   Reply With Quote
Sponsored Links (Register now to hide all advertisements)
Old 04-30-2017, 08:09 PM   #3
Anteek29
Senior Member
 
Anteek29's Avatar
 
Join Date: Dec 2014
Location: Santa Maria, CA
Posts: 984
Default Re: 239 bore.

Side note: I thought the 3.187 bore was for a 221 cube flattie? A 239 flattie would have 3.375 bore? Correct?
__________________
Alan
1929 Special Coupe
1941 Pick-Up
1955 Victoria
Anteek29 is offline   Reply With Quote
Old 04-30-2017, 08:11 PM   #4
Anteek29
Senior Member
 
Anteek29's Avatar
 
Join Date: Dec 2014
Location: Santa Maria, CA
Posts: 984
Default Re: 239 bore.

OOPS...I was waaay wrong - sorry!
__________________
Alan
1929 Special Coupe
1941 Pick-Up
1955 Victoria
Anteek29 is offline   Reply With Quote
Old 04-30-2017, 09:38 PM   #5
WestCoast
Senior Member
 
Join Date: Sep 2014
Location: oroville calif
Posts: 893
Default Re: 239 bore.

a 239 stock engine is 3 3/16" inch bore (3 /.187") using hasting steel vent rings I have gone way past the books engine tolerance specs, ran strong and no smoke, good for around 40,000 miles
WestCoast is offline   Reply With Quote
Old 04-30-2017, 10:17 PM   #6
Ol' Ron
Senior Member
 
Ol' Ron's Avatar
 
Join Date: May 2010
Location: Chester Vt
Posts: 8,841
Default Re: 239 bore.

Sponsored Links (Register now to hide all advertisements)
The auto-thermic pistons can be set to .0015/.002 skirt to wall clearance. This style piston was commonly used from 45/53, and most replacement pistons for the 39 up are of this style. Not sure of the early pistons. .006 is alittle much.
Ol' Ron is offline   Reply With Quote
Old 04-30-2017, 10:30 PM   #7
quickchange34
Senior Member
 
quickchange34's Avatar
 
Join Date: May 2010
Location: charlottesville, Va.
Posts: 588
Default Re: 239 bore.

You need to use a bore gauge and check the taper in the bores frist If you have 6th taper all you are doing by putting new pistons and rings in is adding a band aid to the problem.
quickchange34 is offline   Reply With Quote
Old 05-01-2017, 07:10 AM   #8
Frank Miller
Senior Member
 
Frank Miller's Avatar
 
Join Date: May 2010
Location: Auburn, MA
Posts: 2,106
Default Re: 239 bore.

As a quick inspection, see how much ridge there is at the top. As someone said you need to remove it to prevent breaking rings. Wear typically occurs more at the top due to the ring pressure. Someone said with just new rings you're putting a band aid on it but if funds are lacking and you just want it to run reasonably well, new rings may do what you need. If this is an 8ba and this far apart, new bearings might also be a good idea.
__________________
“The technique of infamy is to start two lies at once and get people arguing heatedly over which is true.” ~ Ezra Pound
Frank Miller is offline   Reply With Quote
Old 05-01-2017, 08:06 AM   #9
Ronnie
Senior Member
 
Ronnie's Avatar
 
Join Date: May 2010
Location: Canada Where it snows
Posts: 2,058
Default Re: 239 bore.

To get a close idea of your taper all that is required is square up one of your existing rings in the bottom of the bore and measure the end gap.Do that three times starting at the bottom then half way up and last at the top under the ridge compare your findings as to end gap and you can calculate the taper as the end gap increases with the formula of PI. Every .001" increase in bore will give an increase of .00314" end gap.

R
Ronnie is offline   Reply With Quote
Old 05-01-2017, 08:37 AM   #10
JSeery
Member Emeritus
 
JSeery's Avatar
 
Join Date: Nov 2012
Location: Wichita KS
Posts: 16,132
Default Re: 239 bore.

Interesting approach Ronnie.
JSeery is offline   Reply With Quote
Old 05-01-2017, 08:53 AM   #11
Ronnie
Senior Member
 
Ronnie's Avatar
 
Join Date: May 2010
Location: Canada Where it snows
Posts: 2,058
Default Re: 239 bore.

Quote:
Originally Posted by JSeery View Post
Interesting approach Ronnie.
Not my first rodeo It does work and you know where I learned that don't you "lol"

R
Ronnie is offline   Reply With Quote
Old 05-01-2017, 09:03 AM   #12
cmbrucew
Senior Member
 
cmbrucew's Avatar
 
Join Date: Dec 2010
Location: North of sandy ago, CA.
Posts: 2,063
Default Re: 239 bore.

Quote:
Originally Posted by Ronnie View Post
To get a close idea of your taper all that is required is square up one of your existing rings in the bottom of the bore and measure the end gap.Do that three times starting at the bottom then half way up and last at the top under the ridge compare your findings as to end gap and you can calculate the taper as the end gap increases with the formula of PI. Every .001" increase in bore will give an increase of .00314" end gap.

R
Why didn't I think of that. Trying to get my big hands, and an inside mic just right is a chore I can do without.
Thanks Ronnie
Bruce
__________________
Works good
Lasts long time
cmbrucew is offline   Reply With Quote
Old 05-01-2017, 09:43 AM   #13
Curt in AZ
Senior Member
 
Curt in AZ's Avatar
 
Join Date: Sep 2015
Location: Clarkdale, AZ
Posts: 121
Default Re: 239 bore.

I use the same technique as Ronnie. Probably obvious but use a piston to push the ring into position to make certain it's square in the bore.
Curt in AZ is offline   Reply With Quote
Old 05-01-2017, 01:10 PM   #14
JSeery
Member Emeritus
 
JSeery's Avatar
 
Join Date: Nov 2012
Location: Wichita KS
Posts: 16,132
Default Re: 239 bore.

Quote:
Originally Posted by Ronnie View Post
Not my first rodeo It does work and you know where I learned that don't you "lol"

R
I'm spoiled, I always get someone to loan me a bore gauge! I don't like telescope gauges myself, to hard to get consistent readings.
JSeery is offline   Reply With Quote
Old 05-01-2017, 02:00 PM   #15
Bored&Stroked
Senior Member
 
Bored&Stroked's Avatar
 
Join Date: Jan 2011
Location: Central Ohio
Posts: 5,011
Default Re: 239 bore.

Quote:
Originally Posted by JSeery View Post
I'm spoiled, I always get someone to loan me a bore gauge! I don't like telescope gauges myself, to hard to get consistent readings.
Exactly! And a good 3 point bore gauge - not one of the el-cheapo ones . . . thy typically cost over $1000 new!
Bored&Stroked is offline   Reply With Quote
Old 05-01-2017, 02:07 PM   #16
flatheadmurre
Senior Member
 
flatheadmurre's Avatar
 
Join Date: Apr 2015
Location: Sweden
Posts: 3,045
Default Re: 239 bore.

The setting gauge for the bore gauge isnīt a to fun investment either...but if you canīt trust what you measure itīs not much good either.
flatheadmurre is offline   Reply With Quote
Old 05-01-2017, 04:16 PM   #17
Ronnie
Senior Member
 
Ronnie's Avatar
 
Join Date: May 2010
Location: Canada Where it snows
Posts: 2,058
Default Re: 239 bore.

First you need to be consistent.I have grown up using measuring equipment.Telescope measuring is a good way to get a measurement but then you need a micrometer to read the gauge.You now have 2 investments.Most non machinist people don't know how to use a telescoping gauge.I have seen some struggling and not liking the results.It takes 10 seconds to get the size done.If you are fiddling around you are doing it wrong.

R
Ronnie is offline   Reply With Quote
Old 05-01-2017, 08:29 PM   #18
Bored&Stroked
Senior Member
 
Bored&Stroked's Avatar
 
Join Date: Jan 2011
Location: Central Ohio
Posts: 5,011
Default Re: 239 bore.

Quote:
Originally Posted by Ronnie View Post
First you need to be consistent.I have grown up using measuring equipment.Telescope measuring is a good way to get a measurement but then you need a micrometer to read the gauge.You now have 2 investments.Most non machinist people don't know how to use a telescoping gauge.I have seen some struggling and not liking the results.It takes 10 seconds to get the size done.If you are fiddling around you are doing it wrong.

R
Yes - and I have used them a plenty. But when you're trying to measure the bore of something - especially a LONG cylinder, it is sure nice to have a precision dial bore gauge . . . that you can slide up/down the bore - then switch to a 90 degree location and do it again . . . just can't beat it. (Now that is just one mans opinion!). Same goes for measuring the mains on an engine - using a LONG dial bore gauge that makes it easy to start on #1 and work your way back.

Last edited by Bored&Stroked; 05-01-2017 at 08:35 PM.
Bored&Stroked is offline   Reply With Quote
Old 05-02-2017, 02:10 AM   #19
pooch
Senior Member
 
pooch's Avatar
 
Join Date: Sep 2010
Location: South Coast NSW Australia
Posts: 2,596
Default Re: 239 bore.

Ronnie, thanks for good trick.

Frank, absolutely zero ridge , I cannot understand it on a standard bore.

Block is in shop now to get a guy to measure bore.

Have another Q, are (mushroom) intake and exhaust valves identical ?

I have a box of stainless valves that look almost new here.

Are these Ok to use in a standard block ? ie no hardened seats .
pooch is offline   Reply With Quote
Old 05-02-2017, 08:59 PM   #20
Bored&Stroked
Senior Member
 
Bored&Stroked's Avatar
 
Join Date: Jan 2011
Location: Central Ohio
Posts: 5,011
Default Re: 239 bore.

Quote:
Originally Posted by pooch View Post
Ronnie, thanks for good trick.
Have another Q, are (mushroom) intake and exhaust valves identical ?
I've always seen different valves for intakes versus exhausts from the factory in all the 32-48 engines (from the factory). Now, I'm sure there are many cases where this doesn't hold up - but generally it was true.

With that said - I've taken apart many rebuilt flatheads where all sorts of intake versus exhaust combinations were used - so I don't know if it actually makes any difference. I don't know if there were different alloys or material properties between the two different valves from Ford.

Anybody know the details?

B&S
Bored&Stroked is offline   Reply With Quote
Reply

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump

Sponsored Links (Register now to hide all advertisements)


All times are GMT -5. The time now is 12:05 PM.