Go Back   The Ford Barn > General Discussion > Model A (1928-31)

Sponsored Links (Register now to hide all advertisements)

Reply
 
Thread Tools Display Modes
Old 07-07-2020, 01:31 PM   #1
Dennisfly
Senior Member
 
Dennisfly's Avatar
 
Join Date: Oct 2019
Location: Virginia
Posts: 140
Default King Pin Retaining Bolts

My king pin retaining pins/bolts have been installed backwards. They were inserted from the rear of the axle and the nut/steering stop is on the front. I became aware of this when the inside of my left front tire rubbed on the brake rod during a tight turn. I figured I could just remove them and reinstall in the proper direction. I removed the nut and lock washer, reinstalled the nut loosely with some space under it and tried to drive the pin out. No luck. I’m using a 24 oz hammer with a long drift rod. I’ve tried with weight on and off the wheels. There is no rust visible, the king pins have no play, and I believe these were rebuilt within the last several years.


Should I go with a five pound sledge or is there something else here that I’m unaware of?
__________________
1929 Town Sedan (Briggs) 155B, Mitchell Overdrive
1935 Model 48 Tudor

Last edited by Dennisfly; 07-07-2020 at 01:50 PM.
Dennisfly is offline   Reply With Quote
Old 07-07-2020, 01:46 PM   #2
ryanheacox
Senior Member
 
ryanheacox's Avatar
 
Join Date: Apr 2013
Location: Northwest CT
Posts: 1,092
Default Re: King Pin Retaining Bolts

I had to drive mine out with a sledge and even then it took some beating. Could apply some heat too but the sledge should definitely work.
ryanheacox is offline   Reply With Quote
Sponsored Links (Register now to hide all advertisements)
Old 07-07-2020, 02:15 PM   #3
MAG
Senior Member
 
MAG's Avatar
 
Join Date: May 2010
Location: Austin, Texas
Posts: 925
Default Re: King Pin Retaining Bolts

"I became aware of this when the inside of my left front tire rubbed on the brake rod during a tight turn." Firestone tires?
__________________
I noticed the harder I work the luckier I get!
MAG is offline   Reply With Quote
Old 07-07-2020, 02:49 PM   #4
mrraford
Senior Member
 
Join Date: Jul 2012
Posts: 190
Default Re: King Pin Retaining Bolts

The holes through the axle are tapered so you could conceivably be trying to drive the bolts against the taper.
I have had the opportunity to make the mistake of installing the axle backwards and therefore try to install against the taper. A lesson in humility.
mrraford is offline   Reply With Quote
Old 07-07-2020, 02:57 PM   #5
Bill G
Senior Member
 
Bill G's Avatar
 
Join Date: Jun 2017
Location: Walla Walla, WA
Posts: 1,044
Default Re: King Pin Retaining Bolts

Even with normal installation, I have had to hammer on them to get them out. Be sure to put the domed nut on the bolt a good distance and beat on the domed nut so you don't screw up the threads on the bolt.
Bill G is offline   Reply With Quote
Old 07-07-2020, 03:28 PM   #6
Marshall V. Daut
Senior Member
 
Join Date: Apr 2011
Location: Davenport, Iowa
Posts: 2,083
Default Re: King Pin Retaining Bolts

Sponsored Links (Register now to hide all advertisements)
Check your private messages in the upper right corner of this webpage.
Marshall
Marshall V. Daut is online now   Reply With Quote
Old 07-07-2020, 03:29 PM   #7
Jacksonlll
Senior Member
 
Jacksonlll's Avatar
 
Join Date: Jul 2012
Location: Michigan-- Member of Oakleaf of MARC
Posts: 1,686
Send a message via ICQ to Jacksonlll
Default Re: King Pin Retaining Bolts

If they fit ok before and they won’t now, your axle is backwards. Easier to just leave it the way it was unless you are up to the job.
Jacksonlll is offline   Reply With Quote
Old 07-07-2020, 05:30 PM   #8
David R.
Senior Member
 
Join Date: Aug 2016
Location: West Virginia
Posts: 430
Default Re: King Pin Retaining Bolts

The holes in my AA axle aren’t tapered but the pins are. They wedge against the flat on the king pin. I measured the holes with an inside caliper because I thought they would be tapered but they aren’t.
David R. is offline   Reply With Quote
Old 07-07-2020, 05:33 PM   #9
daren007
Senior Member
 
Join Date: Apr 2015
Location: Saint Cloud Mn
Posts: 745
Default Re: King Pin Retaining Bolts

I’m going with David. The axle does not care.
daren007 is offline   Reply With Quote
Old 07-07-2020, 07:23 PM   #10
Dennisfly
Senior Member
 
Dennisfly's Avatar
 
Join Date: Oct 2019
Location: Virginia
Posts: 140
Default Re: King Pin Retaining Bolts

Quote:
Originally Posted by MAG View Post
"I became aware of this when the inside of my left front tire rubbed on the brake rod during a tight turn." Firestone tires?

I do have Firestone tires, but I'm thinking that if the turn stop nuts were on the back side of the axle as they should be, this wouldn't have happened.
__________________
1929 Town Sedan (Briggs) 155B, Mitchell Overdrive
1935 Model 48 Tudor
Dennisfly is offline   Reply With Quote
Old 07-07-2020, 07:26 PM   #11
Dennisfly
Senior Member
 
Dennisfly's Avatar
 
Join Date: Oct 2019
Location: Virginia
Posts: 140
Default Re: King Pin Retaining Bolts

Quote:
Originally Posted by Jacksonlll View Post
If they fit ok before and they won’t now, your axle is backwards. Easier to just leave it the way it was unless you are up to the job.

I thought I read somewhere that the axle could properly be installed either way, but I certainly could be wrong.
__________________
1929 Town Sedan (Briggs) 155B, Mitchell Overdrive
1935 Model 48 Tudor
Dennisfly is offline   Reply With Quote
Old 07-07-2020, 07:27 PM   #12
Synchro909
Senior Member
 
Synchro909's Avatar
 
Join Date: Jun 2014
Location: Melbourne, Australia
Posts: 7,472
Default Re: King Pin Retaining Bolts

I've always found the cotter pins could go in from either side.
I STRONGLY advise against any hammering to get them in. The result of doing that is the king pin eye in the end of the axle gets stretched and the stub axle behaves just like the bushes are flogged out. I am about to take my Brother in Law's front axle to have this repaired after a previous owner drove the cotters in too far. Once that is done, I'm sure we will be able to remove the steering stabilizer they put on there to cover the problem.
__________________
I'm part of the only ever generation with an analogue childhood and a digital adulthood.
Synchro909 is offline   Reply With Quote
Old 07-07-2020, 09:47 PM   #13
chrs1961815
Senior Member
 
chrs1961815's Avatar
 
Join Date: Jul 2018
Location: Spring Grove, Illinois
Posts: 1,371
Default Re: King Pin Retaining Bolts

Also, be extremely careful when tightening those nuts. I broke one recently by going a little too far with a socket. Learned my lesson - use a wrench instead and take it easy.
__________________
"The more things change, the more they stay the same."
chrs1961815 is offline   Reply With Quote
Old 07-08-2020, 06:55 AM   #14
old31
Senior Member
 
Join Date: Jan 2016
Posts: 2,088
Default Re: King Pin Retaining Bolts

Chris, what did you do for a repair. Ouch!
old31 is offline   Reply With Quote
Old 07-08-2020, 07:26 AM   #15
chrs1961815
Senior Member
 
chrs1961815's Avatar
 
Join Date: Jul 2018
Location: Spring Grove, Illinois
Posts: 1,371
Default Re: King Pin Retaining Bolts

I just drove the pin back out and got another one.
__________________
"The more things change, the more they stay the same."
chrs1961815 is offline   Reply With Quote
Old 07-08-2020, 10:49 AM   #16
katy
Senior Member
 
katy's Avatar
 
Join Date: Jun 2015
Location: Red Deer, Alberta
Posts: 5,011
Default Re: King Pin Retaining Bolts

Quote:
Originally Posted by Dennisfly View Post
My king pin retaining pins/bolts have been installed backwards. They were inserted from the rear of the axle and the nut/steering stop is on the front. I became aware of this when the inside of my left front tire rubbed on the brake rod during a tight turn. I figured I could just remove them and reinstall in the proper direction. I removed the nut and lock washer, reinstalled the nut loosely with some space under it and tried to drive the pin out. No luck. I’m using a 24 oz hammer with a long drift rod. I’ve tried with weight on and off the wheels. There is no rust visible, the king pins have no play, and I believe these were rebuilt within the last several years.


Should I go with a five pound sledge or is there something else here that I’m unaware of?
I would try: put the nut(s) back on loose, install the cotter pins, go for a drive, then try removing the pins. May or may not work, but it's worth a try.
__________________
If you don't hear a rumor by 10 AM, start one!.
Got my education out behind the barn!
katy is online now   Reply With Quote
Old 07-08-2020, 06:40 PM   #17
daren007
Senior Member
 
Join Date: Apr 2015
Location: Saint Cloud Mn
Posts: 745
Default Re: King Pin Retaining Bolts

Once again, The axle does not care.
daren007 is offline   Reply With Quote
Old 07-08-2020, 07:28 PM   #18
Dennisfly
Senior Member
 
Dennisfly's Avatar
 
Join Date: Oct 2019
Location: Virginia
Posts: 140
Default Re: King Pin Retaining Bolts

Quote:
Originally Posted by katy View Post
I would try: put the nut(s) back on loose, install the cotter pins, go for a drive, then try removing the pins. May or may not work, but it's worth a try.

There are no Cotter pins. There is a lock washer and a special nut/steering stop.
Attached Images
File Type: jpg 3239-300x400.jpg (7.6 KB, 10 views)
File Type: jpg 3241-600x800.jpg (19.8 KB, 10 views)
__________________
1929 Town Sedan (Briggs) 155B, Mitchell Overdrive
1935 Model 48 Tudor
Dennisfly is offline   Reply With Quote
Old 07-08-2020, 07:45 PM   #19
John
Senior Member
 
John's Avatar
 
Join Date: May 2010
Location: Richmond, VA
Posts: 187
Default Re: King Pin Retaining Bolts

Sometimes a hand held pneumatic hammer will "rattle" items loose that otherwise seemed to be joined together for good. Add a bit of your own penetrating oil to the joint for luck.


John
John is offline   Reply With Quote
Old 07-08-2020, 10:28 PM   #20
Synchro909
Senior Member
 
Synchro909's Avatar
 
Join Date: Jun 2014
Location: Melbourne, Australia
Posts: 7,472
Default Re: King Pin Retaining Bolts

Quote:
Originally Posted by Dennisfly View Post
There are no Cotter pins. There is a lock washer and a special nut/steering stop.
That is a cotter pin on the left.
__________________
I'm part of the only ever generation with an analogue childhood and a digital adulthood.
Synchro909 is offline   Reply With Quote
Reply

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump

Sponsored Links (Register now to hide all advertisements)


All times are GMT -5. The time now is 07:38 PM.