|
Sponsored Links (Register now to hide all advertisements) |
|
|
Thread Tools | Display Modes |
01-27-2024, 09:22 PM | #1 |
Senior Member
Join Date: May 2010
Location: 215 E. 6th Street Northport, Michigan 49670
Posts: 941
|
54 Mercury 256 oil return tub question
Anyone know where I can pick up the gaskets for the front of the oil return tube on a 256 engine shown in this photo lower left corner???
Part no. 6648 and 6643 It's the oil tube on the outside of the oil pan from the pump to the pan
__________________
Bob from Northport Northport, Michigan Last edited by Bob from Northport; 02-05-2024 at 08:22 PM. |
01-27-2024, 10:06 PM | #2 |
Senior Member
Join Date: Mar 2013
Location: Kent, WA. Tucson, AZ
Posts: 1,398
|
Re: 54 Mercury 256 oil return tub question
I’ve got all kinds of gaskets I don’t recognize in my Yblock gasket sets. Maybe those, I know I’ve got a stack of small port manifold gaskets. Unfortunately, I’m 1600 miles away right now, and will be for a month. Maybe someone else can take a look and see what they’ve got left over. By the way, that’s the pickup tube, not the return. If you can edit the title it might help.
|
Sponsored Links (Register now to hide all advertisements) |
|
01-28-2024, 07:05 AM | #3 |
Senior Member
Join Date: Aug 2012
Location: IN A 'GALAXIE' FAR FAR AWAY
Posts: 6,475
|
Re: 54 Mercury 256 oil return tub question
|
01-28-2024, 09:37 AM | #4 |
Senior Member
Join Date: May 2010
Location: 215 E. 6th Street Northport, Michigan 49670
Posts: 941
|
Re: 54 Mercury 256 oil return tub question
The site shows nothing for a 256 ENGINE.
__________________
Bob from Northport Northport, Michigan |
01-28-2024, 01:38 PM | #5 |
Senior Member
Join Date: Aug 2012
Location: IN A 'GALAXIE' FAR FAR AWAY
Posts: 6,475
|
Re: 54 Mercury 256 oil return tub question
Read the introductory page -
It will say in the index - - 1954, 256 Merc, Truck 1954-55.......[572-3] - If you go into it, it will show a blow-up of the complete engine overhaul gasket set with each gasket described and listed. I don't know if they sell the gaskets individually, you will have to call and ask. There was a discussion recently @ y-blocksforum.com on this exact subject, that being the early two-piece tube and the later one piece. Maybe ask over there and someone will have the old gaskets setup (gasket sets come with both early and late style) and will mail them to you. Did you get my PM regarding the center caps?
__________________
***** - WHY IS IT ... - ... that everything you buy in the grocery store is either wrapped in or contained in plastic but the government doesn't want you to carry it out in a plastic bag? WONDERING IN W(BY GOD)V ...
DIAGNOSED CDO - (OCD In Correct Alphabetical Order) |
01-28-2024, 02:47 PM | #6 |
Senior Member
Join Date: May 2010
Location: Midland Park, NJ
Posts: 3,982
|
Re: 54 Mercury 256 oil return tub question
Sponsored Links (Register now to hide all advertisements)
While I am not 100 % positive, I believe that all the Y Blocks used the same gaskets in that area.
__________________
48 Ford Conv 56 Tbird 54 Ford Victoria |
01-28-2024, 03:09 PM | #7 |
Senior Member
Join Date: May 2010
Location: Midland Park, NJ
Posts: 3,982
|
Re: 54 Mercury 256 oil return tub question
I have the 6648. I will send it to you. I still have your address. If you have the info on the other I may have that and will send it with the 6648
__________________
48 Ford Conv 56 Tbird 54 Ford Victoria |
01-28-2024, 05:50 PM | #8 |
Senior Member
Join Date: May 2010
Location: 215 E. 6th Street Northport, Michigan 49670
Posts: 941
|
Re: 54 Mercury 256 oil return tub question
Paul,
I will have to wait till I remove the pipe tomorrow to measure the size. Thank You!!
__________________
Bob from Northport Northport, Michigan |
01-29-2024, 06:46 PM | #9 |
Senior Member
Join Date: May 2010
Location: 215 E. 6th Street Northport, Michigan 49670
Posts: 941
|
Re: 54 Mercury 256 oil return tub question
Paul
I removed the pipe today. The diameter of the inside hole on the end of the pipe is 5/8"
__________________
Bob from Northport Northport, Michigan Last edited by Bob from Northport; 02-05-2024 at 08:22 PM. |
01-29-2024, 08:14 PM | #10 |
Senior Member
Join Date: May 2010
Location: Midland Park, NJ
Posts: 3,982
|
Re: 54 Mercury 256 oil return tub question
Bob - I meant the size of the round gasket (6643) that your looking for. Inner and outer diameters, thickness (I realize that it may be compressed).
__________________
48 Ford Conv 56 Tbird 54 Ford Victoria |
01-29-2024, 09:23 PM | #11 |
Senior Member
Join Date: May 2010
Location: 215 E. 6th Street Northport, Michigan 49670
Posts: 941
|
Re: 54 Mercury 256 oil return tub question
The hole has a ledge around it that the gasket sits on. The diameter of the gasket on the outside is 5/8". The gasket sits down into the hole slightly. Inner diameter would be 1/2"
__________________
Bob from Northport Northport, Michigan |
02-01-2024, 08:02 PM | #12 |
Senior Member
Join Date: May 2010
Location: Midland Park, NJ
Posts: 3,982
|
Re: 54 Mercury 256 oil return tub question
Sent out the 6648 (2) out today. Also included a 6625 gasket which I
am sure you will need. The other gasket I don't have, but you might try an O Ring for it.
__________________
48 Ford Conv 56 Tbird 54 Ford Victoria |
02-01-2024, 10:27 PM | #13 |
Senior Member
Join Date: May 2010
Location: 215 E. 6th Street Northport, Michigan 49670
Posts: 941
|
Re: 54 Mercury 256 oil return tub question
Let me know what I owe you please!! Thanks!!
__________________
Bob from Northport Northport, Michigan |
02-02-2024, 09:27 PM | #14 |
Senior Member
Join Date: May 2010
Location: Midland Park, NJ
Posts: 3,982
|
Re: 54 Mercury 256 oil return tub question
You owe me nothing. Just a few extra gaskets I had lying around and no use for as I have the one piece inlet tube in both of my YBlock cars. Just wish I had the other one you are looking for.
__________________
48 Ford Conv 56 Tbird 54 Ford Victoria |
02-03-2024, 01:31 PM | #15 |
Senior Member
Join Date: May 2010
Location: 215 E. 6th Street Northport, Michigan 49670
Posts: 941
|
Re: 54 Mercury 256 oil return tub question
The one that came off my vehicle engine is a one piece tube
__________________
Bob from Northport Northport, Michigan Last edited by Bob from Northport; 02-05-2024 at 08:22 PM. |
02-03-2024, 01:43 PM | #16 |
Senior Member
Join Date: Aug 2012
Location: IN A 'GALAXIE' FAR FAR AWAY
Posts: 6,475
|
Re: 54 Mercury 256 oil return tub question
|
02-03-2024, 06:07 PM | #17 |
Senior Member
Join Date: May 2010
Location: 215 E. 6th Street Northport, Michigan 49670
Posts: 941
|
Re: 54 Mercury 256 oil return tub question
I managed to locate a NOS an oil pipe exactly like the one I removed from my 256 engine
__________________
Bob from Northport Northport, Michigan Last edited by Bob from Northport; 02-05-2024 at 08:22 PM. |
02-03-2024, 08:16 PM | #18 |
Senior Member
Join Date: May 2010
Location: Midland Park, NJ
Posts: 3,982
|
Re: 54 Mercury 256 oil return tub question
Actually, it is not. The one piece tube has the pickup attached to the tube and does not have the triangle piece where you have to attach the pick up. The pic shown is for a TBird which has a much shorter tube than a sedan.
__________________
48 Ford Conv 56 Tbird 54 Ford Victoria |
02-04-2024, 09:46 AM | #19 | ||
Senior Member
Join Date: Aug 2012
Location: IN A 'GALAXIE' FAR FAR AWAY
Posts: 6,475
|
Re: 54 Mercury 256 oil return tub question
Quote:
Quote:
This ain't that hard people.
__________________
***** - WHY IS IT ... - ... that everything you buy in the grocery store is either wrapped in or contained in plastic but the government doesn't want you to carry it out in a plastic bag? WONDERING IN W(BY GOD)V ...
DIAGNOSED CDO - (OCD In Correct Alphabetical Order) |
||
|
|
Sponsored Links (Register now to hide all advertisements) |
|