|
Sponsored Links (Register now to hide all advertisements) |
|
|
Thread Tools | Display Modes |
03-08-2018, 09:46 PM | #1 |
Senior Member
Join Date: Sep 2016
Posts: 274
|
Pulling an engine
Murphy’s law got me again so I’m having to pull the motor out of my 36 truck. When I put it in I used a cherry picker that seemed to be a tad to short to reach all the way. I also used a chain with bolts from the head. My 3 questions are is there a good “engine plate” like you would use on a small block to pull it out. Is there a specific cherry picker that you guys have used that reaches well and any idea where to get a flat head engine stand.
Thanks. |
03-08-2018, 09:50 PM | #2 |
Senior Member
Join Date: Aug 2016
Location: Southern Illinois
Posts: 230
|
Re: Pulling an engine
If someone has a chain hoist or loader in the area they're really helpful when trying to pull the engine out. The engine stand I use is one that rotates 360°. I can share a link to a similar one. And I think I answered all questions.
Sent from my SM-G955U using Tapatalk |
Sponsored Links (Register now to hide all advertisements) |
|
03-08-2018, 09:51 PM | #3 |
Senior Member
Join Date: Aug 2016
Location: Southern Illinois
Posts: 230
|
Re: Pulling an engine
Oh to lift it out we used bolts and a small chain on the chain hoist or loader to lift it out of the car.
Sent from my SM-G955U using Tapatalk |
03-08-2018, 10:01 PM | #4 |
Senior Member
Join Date: Aug 2016
Location: Southern Illinois
Posts: 230
|
Re: Pulling an engine
House of fab on ford barn has the flathead engine mount that goes in the rotating engine stand. Not sure where the one my buddy has came from.
Sent from my SM-G955U using Tapatalk |
03-08-2018, 11:38 PM | #5 |
Senior Member
Join Date: Nov 2015
Location: North Pole, Alaska
Posts: 2,651
|
Re: Pulling an engine
I made a simple flat plate from an intake gasket, with a verticle center piece with three large holes in center to hoist by, depending on balance which hole you use. Can use hook from hoist direct, eliminating chain.
|
03-08-2018, 11:41 PM | #6 |
Senior Member
Join Date: Nov 2015
Location: North Pole, Alaska
Posts: 2,651
|
Re: Pulling an engine
Sponsored Links (Register now to hide all advertisements)
|
03-09-2018, 08:06 AM | #7 |
Senior Member
Join Date: Jun 2013
Location: Marana Arizona
Posts: 1,776
|
Re: Pulling an engine
When I pulled the tranny out of my truck I wanted to bring it out from the top but being an old man with a trashed back I wanted to use my engine hoist. The arm was not long enough to make that idea work. I went to the medal supply store and got a piece of 2"x2" thick walled square steel tubing that I could insert into the arm on my hoist.. (They actually gave it to me.) Drilled it, slipped it into the end of the hoist arm, pinned it in place and thus ended up with the extra 6" of reach I needed. It was a snug fit and worked great.
Of course there are weight limit and safety concerns, but if you just need a few inches of reach this may work for you. |
03-09-2018, 08:30 AM | #8 |
Senior Member
Join Date: May 2010
Location: Illinois
Posts: 2,184
|
Re: Pulling an engine
That is what I did. I made a new arm longer so it reached out to the end of hoist legs. I usually leave it stock length unless I need more reach.
John |
03-09-2018, 08:37 AM | #9 |
Senior Member
Join Date: Jun 2010
Location: Marana, AZ
Posts: 1,194
|
Re: Pulling an engine
I had a similar problem with my shop crane being a "little to short" to get my rebuilt block back in my '47. It was a 1.5 ton I bought years ago back in PA. It worked fine for my '39 but the '47 needed a longer reach. Not sure where you are, 1st, but I found a 2 ton on sale here at Pep Boys in Marana AZ that had just the right amount of reach.
I also use an adjustable leveling plate bolted to the top of the block that lets me change the angle during the install....very happy with it and think I found it on line. Good luck....Dick. |
03-09-2018, 08:49 AM | #10 | |
Member Emeritus
Join Date: Nov 2012
Location: Wichita KS
Posts: 16,132
|
Re: Pulling an engine
Quote:
|
|
03-09-2018, 09:45 AM | #11 |
Senior Member
Join Date: Jun 2013
Location: Marana Arizona
Posts: 1,776
|
Re: Pulling an engine
Mine goes into hoist arm and is secured with the original pin. Then the end of the hoist arm slips over the extension and is secured with a bolt.
I tried to attach photos and couldn't them to upload??? |
03-09-2018, 10:08 AM | #12 |
Senior Member
Join Date: May 2010
Location: Montgomery, NY & Port St. Lucie Florida
Posts: 936
|
Re: Pulling an engine
I made a flat plate out of 1/2'' aluminum to bolt in place of the intake manifold. I put some brackets on it to mount my engine leveler. Now I can pick the engine up or drop it in at any angle just by turning the crank on the leveler.
__________________
Early Ford Lock & Key Service http://www.fordbarn.com/forum/showthread.php?t=46583 |
03-15-2018, 03:09 AM | #13 |
Senior Member
Join Date: May 2010
Location: Solihull, England.
Posts: 8,755
|
Re: Pulling an engine
I bought one of those load leveller jobs. It has four chains with angle braclkets. I remove 4 manifold bolts, insert longer bolts (no need to tighten them) and the cherrypicker lifts the whole lot out no problem. I slightly lengthened the chains so I could pull the roadster motor with high rise thickstun and twin carbs still intact. You can cheat the cherrypicker a little bit for extra reach but don't overdo it.
Mart. |
03-15-2018, 04:17 PM | #14 |
Senior Member
Join Date: May 2010
Location: PA Poconos
Posts: 723
|
Re: Pulling an engine
I have one of he leveling devices mentioned by Mart. I think it was cheap at Harbor Freight and works great!!
|
05-25-2018, 06:50 PM | #15 |
Senior Member
Join Date: Sep 2016
Posts: 274
|
Re: Pulling an engine
I’ve confirmed that the engine has to come out. Wanted to leave front fenders on and needed best advice for removal as to do zero scratching.
Thanks in advance. |
05-26-2018, 10:52 AM | #16 |
Senior Member
Join Date: Jun 2010
Location: Marana, AZ
Posts: 1,194
|
Re: Pulling an engine
Shouldn't have to remove fenders....what an extra pain!!!. I use old moving pads on the fenders and am "really" careful on the way out and on the way back in.
Since I'm not sure where you are located, it's hard to recommend a local source for your engine stand and shop crane in your initial post. Stumpy's Fab Works has a very nice engine stand adapter plate for flatheads that is used with a regular stand. My machine shop, however, bolted my 59AB block directly to their conventional engine stand with no adverse results!!! |
05-26-2018, 10:59 AM | #17 |
Senior Member
Join Date: May 2010
Location: Eagle River,Alaska
Posts: 353
|
Re: Pulling an engine
The motor plate that I made.
|
|
|
Sponsored Links (Register now to hide all advertisements) |
|