Go Back   The Ford Barn > General Discussion > Early V8 (1932-53)

Sponsored Links (Register now to hide all advertisements)

Reply
 
Thread Tools Display Modes
Old 07-25-2020, 09:12 AM   #1
russcc
Senior Member
 
Join Date: May 2010
Posts: 2,871
Default Filling a brakes system

Completed the '40 brake system, New wheel cylinders, master cylinder & hoses, along with flushing out and cleaning all the hard lines. What is the best way to refill the system to minimize bleeding. I am not about to invest in a "power bleeder" or whatever since I have been dong it the hard way for 60 years and it works fine for me. Thank you Fordbarners.
russcc is offline   Reply With Quote
Old 07-25-2020, 09:25 AM   #2
Kube
Senior Member
 
Kube's Avatar
 
Join Date: May 2010
Location: Wisconsin, USA
Posts: 8,935
Default Re: Filling a brakes system

Russ, If you've been doing it the "hard way" for 60 years and it "works fine", there is most likely no advice anyone can give you that you've not already figured out on your own.

I've been power bleeding for perhaps 30+ years and recently (finally) had to replace my system. Cost with shipping was under $100 for one heck of a quality unit.
__________________
"I can explain it for you. However, I can't understand it for you".
Kube is offline   Reply With Quote
Sponsored Links (Register now to hide all advertisements)
Old 07-25-2020, 02:02 PM   #3
Joe Immler
Senior Member
 
Join Date: Dec 2012
Location: Massillon, Ohio
Posts: 783
Default Re: Filling a brakes system

Kube What brand, model etc is it?
Joe Immler is offline   Reply With Quote
Old 07-25-2020, 02:33 PM   #4
Kube
Senior Member
 
Kube's Avatar
 
Join Date: May 2010
Location: Wisconsin, USA
Posts: 8,935
Default Re: Filling a brakes system

Quote:
Originally Posted by Joe Immler View Post
Kube What brand, model etc is it?
Joe,
It's an ATD-5125. I'd received it April 26, 2020. It was just shy of $100 shipped.
I think (if I recall correctly) I bought it from the Tool Warehouse.
I do recall when searching the Web, this model was priced all over the place. The Warehouse was very good to work with and they shipped fast.
I am VERY happy with the quality of this unit and have little doubt it'll outlive me.
__________________
"I can explain it for you. However, I can't understand it for you".
Kube is offline   Reply With Quote
Old 07-25-2020, 02:35 PM   #5
Kube
Senior Member
 
Kube's Avatar
 
Join Date: May 2010
Location: Wisconsin, USA
Posts: 8,935
Default Re: Filling a brakes system

Joe, It went up just a few bucks. Here's the link:
https://www.nationaltoolwarehouse.co...All%20Products
__________________
"I can explain it for you. However, I can't understand it for you".
Kube is offline   Reply With Quote
Old 07-25-2020, 02:42 PM   #6
mrtexas
Senior Member
 
mrtexas's Avatar
 
Join Date: May 2010
Location: Sugar Land, TX
Posts: 4,393
Default Re: Filling a brakes system

Sponsored Links (Register now to hide all advertisements)
Quote:
Originally Posted by Kube View Post
Joe,
It's an ATD-5125. I'd received it April 26, 2020. It was just shy of $100 shipped.
I think (if I recall correctly) I bought it from the Tool Warehouse.
I do recall when searching the Web, this model was priced all over the place. The Warehouse was very good to work with and they shipped fast.
I am VERY happy with the quality of this unit and have little doubt it'll outlive me.
What do you use to attach bleeder to MC?

I use a vacuum bleeder myself.
__________________
41 woodie https://41fordwoodie.weebly.com/
mrtexas is offline   Reply With Quote
Old 07-25-2020, 03:10 PM   #7
Kube
Senior Member
 
Kube's Avatar
 
Join Date: May 2010
Location: Wisconsin, USA
Posts: 8,935
Default Re: Filling a brakes system

Quote:
Originally Posted by mrtexas View Post
What do you use to attach bleeder to MC?

I use a vacuum bleeder myself.
I made a cap with a fitting in it. I suppose it would be easier yet to just take an extra master cylinder cap and drill and tap a hole for the air fitting.

I've always liked the power bleeding system as there is zero doubt all of the air is removed - even from the master.
__________________
"I can explain it for you. However, I can't understand it for you".
Kube is offline   Reply With Quote
Old 07-25-2020, 06:40 PM   #8
russcc
Senior Member
 
Join Date: May 2010
Posts: 2,871
Default Re: Filling a brakes system

We got a little of track here. I have never had to fill a complete system, and likely never will again. It is usually one or two cylinders to bleed. So my question is, how would you start by using gravity to assist. Thank you Fordbarners.
russcc is offline   Reply With Quote
Old 07-25-2020, 07:42 PM   #9
Kube
Senior Member
 
Kube's Avatar
 
Join Date: May 2010
Location: Wisconsin, USA
Posts: 8,935
Default Re: Filling a brakes system

The chances of gravity working well are little to nearly none.
__________________
"I can explain it for you. However, I can't understand it for you".
Kube is offline   Reply With Quote
Old 07-26-2020, 05:39 AM   #10
russcc
Senior Member
 
Join Date: May 2010
Posts: 2,871
Default Re: Filling a brakes system

There must be more opinions out there other than Mike's, as much as we all value his experience. When we are referring to gravity, it is in partially filling the system so as to minimize air entrapment. Thank you Fordbarners. Any other opinions ?
russcc is offline   Reply With Quote
Old 07-26-2020, 08:18 AM   #11
john in illinois
Senior Member
 
john in illinois's Avatar
 
Join Date: May 2010
Location: Illinois
Posts: 2,181
Default Re: Filling a brakes system

I do not think gravity would move the fluid. I used to fill the MC have helper pump the pedal and open farthest bleeder then go to closer one ,etc. You have to always keep fluid in MC.
Now many use speed bleeders to eliminate the helper.

http://speedbleeder.com/



Now Like Kube, I use one of these pressure tanks. Made my own cap with a fitting. I hook a clear hose onto each bleeder and simply walk around opening each bleeder untill no bubbles.

The nice thing about a pressure bleeder is any leaks become immediately apparent.

https://www.amazon.com/motive-power-...+power+bleeder

John
__________________
Welcome each day

Last edited by john in illinois; 07-26-2020 at 08:44 AM.
john in illinois is offline   Reply With Quote
Old 07-26-2020, 08:29 AM   #12
joe 1950
Senior Member
 
joe 1950's Avatar
 
Join Date: Mar 2013
Location: Green Bay Wi
Posts: 400
Default Re: Filling a brakes system

It’s hard to gravity bleed these old systems because the master cyl. is mounted so low any car that has the master on the firewall gravity bleed pretty easy like Kube said power bleeders work the best. good luck
joe 1950 is offline   Reply With Quote
Old 07-26-2020, 08:34 AM   #13
rich b
Senior Member
 
rich b's Avatar
 
Join Date: May 2010
Location: Minnesota
Posts: 1,813
Default Re: Filling a brakes system

The power bleeder (Bendix) I used in the past had a diaphragm between the fluid and the pressurized air; I was taught this was to keep from entraining air into the fluid.

These new bleeders don't separate the two, has something changed?
rich b is offline   Reply With Quote
Old 07-26-2020, 08:42 AM   #14
john in illinois
Senior Member
 
john in illinois's Avatar
 
Join Date: May 2010
Location: Illinois
Posts: 2,181
Default Re: Filling a brakes system

I always put in the fluid I think I will use and then empty and clean bleeder tank. only exposed to air for a few minutes.
I used to use the diaphragm unit in a shop and you could leave the fluid in it.


John
__________________
Welcome each day
john in illinois is offline   Reply With Quote
Old 07-26-2020, 11:12 AM   #15
3twinridges
Senior Member
 
3twinridges's Avatar
 
Join Date: Dec 2015
Posts: 541
Default Re: Filling a brakes system

When using the power bleeder method, is it recommended to also use speed bleeders or are standard bleeder screws sufficient/recommended?

JB
3twinridges is offline   Reply With Quote
Old 07-26-2020, 11:20 AM   #16
38bill
Senior Member
 
38bill's Avatar
 
Join Date: Apr 2014
Location: Minnesota
Posts: 1,162
Default Re: Filling a brakes system

The "power" bleeder pressurizes the brake system and then you open the bleeder valve on the wheel cyl to bleed it. I don't think you wouldn't gain anything by using the speed bleeders.
38bill is offline   Reply With Quote
Old 07-26-2020, 11:54 AM   #17
mrtexas
Senior Member
 
mrtexas's Avatar
 
Join Date: May 2010
Location: Sugar Land, TX
Posts: 4,393
Default Re: Filling a brakes system

My Mityvac works great. No need to make special MC cover.
Attached Images
File Type: jpg mityvac.jpg (66.3 KB, 18 views)
__________________
41 woodie https://41fordwoodie.weebly.com/
mrtexas is offline   Reply With Quote
Old 07-26-2020, 11:59 AM   #18
4t8v8
Senior Member
 
Join Date: Nov 2011
Location: NW Arkansas
Posts: 523
Default Re: Filling a brakes system

I made a vacuum pump out of an old freezer compressor. Use it with a brake bleeder cup. Works great.
4t8v8 is offline   Reply With Quote
Old 07-26-2020, 12:02 PM   #19
3twinridges
Senior Member
 
3twinridges's Avatar
 
Join Date: Dec 2015
Posts: 541
Default Re: Filling a brakes system

Quote:
Originally Posted by 38bill View Post
The "power" bleeder pressurizes the brake system and then you open the bleeder valve on the wheel cyl to bleed it. I don't think you wouldn't gain anything by using the speed bleeders.
Thx bud

JB
3twinridges is offline   Reply With Quote
Old 07-26-2020, 01:35 PM   #20
mrtexas
Senior Member
 
mrtexas's Avatar
 
Join Date: May 2010
Location: Sugar Land, TX
Posts: 4,393
Default Re: Filling a brakes system

I installed a remote fill MC on my 41 and mounted the two fills on the firewall above the wheels. Think this made the bleeding easier like a modern car. But also have bendix on the rear.

https://41fordwoodie.weebly.com/earlyv8discs.html
__________________
41 woodie https://41fordwoodie.weebly.com/
mrtexas is offline   Reply With Quote
Reply

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump

Sponsored Links (Register now to hide all advertisements)


All times are GMT -5. The time now is 07:50 AM.