Go Back   The Ford Barn > General Discussion > Model A (1928-31)

Sponsored Links (Register now to hide all advertisements)

Reply
 
Thread Tools Display Modes
Old 08-26-2019, 08:00 AM   #1
Mrowlett
Junior Member
 
Join Date: Aug 2019
Posts: 11
Default Towing a Model A

Hello, could use some help.
I have a model A chassis, no engine, trans, steering wheel, that I have used to build a mockup delivery truck to be used as a food concession. I am going to tow it like a trailer, there is the problem. When I hook it to my pickup and move the front wheels go sideways after a few feet. How do I get the wheels to follow the pickup without welding the front end? If I do that I will drag the tires when I make a turn.
I have thought about welding brackets and using bungee cords from opposite directions, theory is the wheels might follow but return to center. Don't know.
Please help, thanks.
Mrowlett is offline   Reply With Quote
Old 08-26-2019, 08:12 AM   #2
denis4x4
Senior Member
 
denis4x4's Avatar
 
Join Date: May 2010
Location: Durango CO
Posts: 1,309
Default Re: Towing a Model A

PM me...I recently bought an A chassis with a modification used by farmers to convert a chassis to a wagon. This appears to be a well designed accessory from the 1930's.
__________________
No restorable Model A's were harmed in the building of this truck!
denis4x4 is offline   Reply With Quote
Sponsored Links (Register now to hide all advertisements)
Old 08-26-2019, 08:33 AM   #3
rotorwrench
Senior Member
 
rotorwrench's Avatar
 
Join Date: Jun 2010
Location: San Antonio, Texas
Posts: 16,367
Default Re: Towing a Model A

There has to be a lot of caster when you flat tow a car like this. If there is no transmission, where is the wishbone? It would control the caster. I think I'd leave the steering in there too.
rotorwrench is online now   Reply With Quote
Old 08-26-2019, 08:34 AM   #4
mike657894
Senior Member
 
mike657894's Avatar
 
Join Date: Oct 2015
Location: Bay City Michigan
Posts: 1,050
Default Re: Towing a Model A

if your tow bar pivoted you could set a drag link to the bar that turned the wheels. I have seen hay carts being pulled slow or moving around a lot behind the tractor. how fast do you plan to pull this? you may need something to combat that.


mike657894 is offline   Reply With Quote
Old 08-26-2019, 08:40 AM   #5
Mrowlett
Junior Member
 
Join Date: Aug 2019
Posts: 11
Default Re: Towing a Model A

I built a crossmember for the wishbone, not knowing how much pressure to put on it I raised it till it seemed firm, basically they are close to level. After I did that I could go 10' before sideways wheels.w
Mrowlett is offline   Reply With Quote
Old 08-26-2019, 08:44 AM   #6
Mrowlett
Junior Member
 
Join Date: Aug 2019
Posts: 11
Default Re: Towing a Model A

Sponsored Links (Register now to hide all advertisements)
55-60 mph
Mrowlett is offline   Reply With Quote
Old 08-26-2019, 09:36 AM   #7
SSsssteamer
Senior Member
 
SSsssteamer's Avatar
 
Join Date: Nov 2010
Location: Sedro-Woolley, WA
Posts: 1,023
Default Re: Towing a Model A

I towed our 1930 Model A pick up with a tow bar 1,430 miles on I-5 at 60 MPH without a problem. From 29 Palms, California to Sedro-Woolley, WA. The only place I had a problem was once at a gas station where I had to make a sharp corner and the tires did not return to their center after turning into the gas station. Leave the steering wheel attached, it will slow down the possibility of a jack knife. Otherwise, without a drag link attached, a farmer's wagon steering attached like posted above will serve you well.
SSsssteamer is offline   Reply With Quote
Old 08-26-2019, 11:14 AM   #8
Jim Brierley
Senior Member
 
Join Date: Jun 2010
Location: Temecula, CA
Posts: 4,066
Default Re: Towing a Model A

I have towed my wide-bed pickup many miles. I had to disconnect the drag link at the axle end in order for it to straighten out after a turn. I stuck an old spark plug into the now open end of the drag link so the spring, etc. wouldn't fall out and get lost. You will need some caster to do this.
Jim Brierley is offline   Reply With Quote
Old 08-26-2019, 11:31 AM   #9
rich b
Senior Member
 
rich b's Avatar
 
Join Date: May 2010
Location: Minnesota
Posts: 1,813
Default Re: Towing a Model A

Bracket your tow bar to the axle, block under the frame rails so they are supported, pull the front wheels, and pull it like a trailer.
rich b is offline   Reply With Quote
Old 08-26-2019, 12:08 PM   #10
Mrowlett
Junior Member
 
Join Date: Aug 2019
Posts: 11
Default Re: Towing a Model A

Wondered about that
Mrowlett is offline   Reply With Quote
Old 08-26-2019, 12:10 PM   #11
Mrowlett
Junior Member
 
Join Date: Aug 2019
Posts: 11
Default Re: Towing a Model A

So the higher I lift the wishbone the more castor I get? Or is it like alining the front end?
Mrowlett is offline   Reply With Quote
Old 08-26-2019, 12:18 PM   #12
rotorwrench
Senior Member
 
rotorwrench's Avatar
 
Join Date: Jun 2010
Location: San Antonio, Texas
Posts: 16,367
Default Re: Towing a Model A

Nope. Other way around. The A transmission sets low and the radius rod end mounts down on the bottom of it. Caster is how much the steering knuckle king pins are angled back toward the rear. If it's zero straight up and down or angled forward then there is no caster effect as all.

Camber is done by bending the axle but it should be OK unless the axle has been damage or bent in an accident. Using a draw bar and a pivot point off the front axle with the attachment to twin tie rods as was mentioned was a way to get a steering axle for a hay wagon. It works but it will take a bit of engineering to get it right.

Last edited by rotorwrench; 08-26-2019 at 12:27 PM.
rotorwrench is online now   Reply With Quote
Old 08-26-2019, 03:16 PM   #13
Dodge
Senior Member
 
Join Date: Nov 2011
Location: Sonoma, CA.
Posts: 1,491
Default Re: Towing a Model A

You could split the wishbone and use the brackets on the frame like the hot rod guys do.
Dodge is offline   Reply With Quote
Old 08-26-2019, 07:57 PM   #14
Mrowlett
Junior Member
 
Join Date: Aug 2019
Posts: 11
Default Re: Towing a Model A

Thanks for all the advice guys, really appreciate it.
Mrowlett is offline   Reply With Quote
Reply

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump

Sponsored Links (Register now to hide all advertisements)


All times are GMT -5. The time now is 01:04 PM.