|
Sponsored Links (Register now to hide all advertisements) |
|
|
Thread Tools | Display Modes |
12-04-2014, 04:34 PM | #1 |
Senior Member
Join Date: Jan 2013
Posts: 119
|
Interchange info for banjo rear
I'm aware of some of the different widths.(got wider in '42-'48) What are the can and can't do when it comes to changing bells from year to year? I've got what I think is a 37 center with internals and axles and want to put 36 bells on. Is there a difference in the bearing sizes? Thanks in advance
|
12-04-2014, 09:36 PM | #2 |
Senior Member
Join Date: May 2010
Location: Williamsburg, Virginia
Posts: 2,654
|
Re: Interchange info for banjo rear
TomT here - I am working with Dave on this and we could use some help. Basically we have 37 axles, open drive center from a 42-47 truck, and 36 bells. Seems the 36 bells will not seat to the center section properly - any difference in the 36 vs 37 axles? They are the same length but are the center bearings in a different position? Different size?
Thanks for any help you can give .... |
Sponsored Links (Register now to hide all advertisements) |
|
12-04-2014, 11:27 PM | #3 |
Senior Member
Join Date: May 2010
Location: Kerrville, Tx
Posts: 2,769
|
Re: Interchange info for banjo rear
I put 36 bells on a 40 center. I think you use the later side bearings. You should be fine with either axles.
|
12-05-2014, 02:34 AM | #4 |
Senior Member
Join Date: Jul 2011
Location: SF Bay Area
Posts: 6,644
|
Re: Interchange info for banjo rear
This link should be of some help to you. No help here for open drive, however.
http://www.flatheadv8.org/fordrear.htm
__________________
Alan |
12-05-2014, 10:02 AM | #5 |
Senior Member
Join Date: May 2010
Location: Salado, TX.
Posts: 733
|
Re: Interchange info for banjo rear
What Andy said, the '35-6 bearings and races are a narrower profile than the later. Choose whichever direction you want and match bearings and races on carrier and housing.
__________________
Luck occurs when preparation and opportunity converge. |
12-05-2014, 11:34 AM | #6 | |
Senior Member
Join Date: May 2010
Location: Mill Valley,Ca.
Posts: 1,509
|
Re: Interchange info for banjo rear
Sponsored Links (Register now to hide all advertisements)
Quote:
I put together a rear using 1946 Merc 3.54 drive shaft/pinion (one piece) and carrier/center section with 1936 bells, 1937 axles and spider gears. Use the 1935/6 carrier bearings... It set up with one set of gaskets. Karl |
|
12-05-2014, 01:00 PM | #7 |
Senior Member
Join Date: Jul 2011
Location: SF Bay Area
Posts: 6,644
|
Re: Interchange info for banjo rear
Karl, you probably meant the '39 axle/spider? '35 through '38 were the same.
__________________
Alan |
12-05-2014, 02:07 PM | #8 |
Senior Member
Join Date: May 2010
Location: Williamsburg, Virginia
Posts: 2,654
|
Re: Interchange info for banjo rear
Thanks, gents - now we know we need 35-36 axles and spiders to go with those bells ...
|
12-05-2014, 06:03 PM | #9 |
Senior Member
Join Date: May 2010
Location: Mill Valley,Ca.
Posts: 1,509
|
Re: Interchange info for banjo rear
I would use 1939-41 axles and spider gears, if that was what I had... Just not 1942-48- they're too long...
Karl |
|
|
Sponsored Links (Register now to hide all advertisements) |
|