The Ford Barn

Charles Brock · 08-29-2016, 05:35 PM

Can anyone provide pictures of how the cloth welting is correctly installed on the #1 and #2 floorboards of a '32. In advance, Thanks So Much.

DavidG · 08-29-2016, 07:04 PM

I've no photos handy, but it is pretty straightforward. On the #2 board the black anti-squeak webbing is tacked to the edges of the two sides and back and then folded under and tacked along the undersides of those three edges.

On the #1 board it is tacked to the front edge in the same way and ends at the beginning of the recessed area where the sponge rubber weather seal for the pedals and steering column is located. A short piece of webbing is similarly tacked to the furthest outer edges that start at the bottom of the board. There is no webbing on the upper vertical sides, but rather felt strips are tacked there to serve as a weather seal up against the sides of the cowl. Roy Nacewicz has the felt strips for sale.

Originally, there was no webbing between the rear edge of the #1 board and the front edges of the #2 board.

Charles Brock · 08-30-2016, 02:35 PM

David, Thank you for all your help!!

jim1932 · 08-30-2016, 05:25 PM

https://jrodda.smugmug.com/Cars/HenrysB/i-fmmqqW9

This should give you a good idea. look at photo 170 and up.

Charles Brock · 08-30-2016, 07:59 PM

Sponsored Links (Register now to hide all advertisements)

Jim, Thank you so much

08-30-2016, 02:35 PM	#3
Charles Brock Senior Member Join Date: May 2010 Location: Rome, GA Posts: 120	Re: '32 #1 and #2 Floorboards David, Thank you for all your help!!

08-30-2016, 05:25 PM	#4
jim1932 Senior Member Join Date: Oct 2010 Location: Hancock, MA Posts: 2,781	Re: '32 #1 and #2 Floorboards https://jrodda.smugmug.com/Cars/HenrysB/i-fmmqqW9 This should give you a good idea. look at photo 170 and up. __________________ Short URL: http://smu.gs/14g7eDW

08-30-2016, 07:59 PM	#5
Charles Brock Senior Member Join Date: May 2010 Location: Rome, GA Posts: 120	Re: '32 #1 and #2 Floorboards Sponsored Links (Register now to hide all advertisements) Jim, Thank you so much

08-29-2016, 05:35 PM	#1
Charles Brock Senior Member Join Date: May 2010 Location: Rome, GA Posts: 120	'32 #1 and #2 Floorboards Can anyone provide pictures of how the cloth welting is correctly installed on the #1 and #2 floorboards of a '32. In advance, Thanks So Much.

08-29-2016, 07:04 PM	#2
DavidG Senior Member Join Date: May 2010 Location: southeastern Michigan Posts: 10,101	Re: '32 #1 and #2 Floorboards I've no photos handy, but it is pretty straightforward. On the #2 board the black anti-squeak webbing is tacked to the edges of the two sides and back and then folded under and tacked along the undersides of those three edges. On the #1 board it is tacked to the front edge in the same way and ends at the beginning of the recessed area where the sponge rubber weather seal for the pedals and steering column is located. A short piece of webbing is similarly tacked to the furthest outer edges that start at the bottom of the board. There is no webbing on the upper vertical sides, but rather felt strips are tacked there to serve as a weather seal up against the sides of the cowl. Roy Nacewicz has the felt strips for sale. Originally, there was no webbing between the rear edge of the #1 board and the front edges of the #2 board. Last edited by DavidG; 08-30-2016 at 04:25 PM.