|
Sponsored Links (Register now to hide all advertisements) |
|
|
Thread Tools | Display Modes |
08-30-2013, 08:48 PM | #1 |
Senior Member
Join Date: May 2010
Location: PRINEVILLE, OR.
Posts: 490
|
Update on how it is running
I now have a few hundred miles on my '41 Pickup and feel it is running right. In case it is of any benefit to anyone this is what I have. Checked the plugs (Autolite 0.30 gap) and they are clean and have a light color. Not running thermostats now and it runs around 170 in traffic. Starts right up and takes off fine without any warm up. Don't need fuel regulator. Using stock mechanical pump with electric pump backup to fill carbs before starting.
276 CID merc. crank L100 cam Offie 400 heads Offie triple intake manifold Three 97's with 43 jets, 95 power valves, straight linkage Crab ignition
__________________
KIM KARDASHIAN ISN'T FLAT, BUT MY MOTOR IS..... http://s818.photobucket.com/home/roglehr/index |
08-30-2013, 09:02 PM | #2 |
Senior Member
Join Date: May 2010
Location: Above the gnat line in Georgia
Posts: 7,009
|
Re: Update on how it is running
Great when they are running correctly isn't it?
__________________
Life is like a roll of toilet paper. The closer to the end, the faster it goes. It is better to be seen, than viewed. "We sleep safe in our beds because rough men stand ready in the night to visit violence on those who would do us harm". |
Sponsored Links (Register now to hide all advertisements) |
|
08-30-2013, 10:16 PM | #3 |
Senior Member
Join Date: May 2010
Location: Kokomo, Indiana
Posts: 1,731
|
Re: Update on how it is running
Sounds good. Nice to hear all is well.
__________________
Henry |
08-30-2013, 10:46 PM | #4 |
Senior Member
Join Date: May 2010
Location: Waddell, AZ
Posts: 2,540
|
Re: Update on how it is running
congratulations....now have fun, eh??....Mike
|
08-31-2013, 12:13 AM | #5 |
BANNED
Join Date: May 2010
Location: stratford,ct
Posts: 5,971
|
Re: Update on how it is running
Where in the world did you get #95 PV's or was that typo?? lol. ken ct.
|
08-31-2013, 07:28 PM | #6 |
Senior Member
Join Date: Oct 2012
Location: oroville calif.
Posts: 1,453
|
Re: Update on how it is running
Sponsored Links (Register now to hide all advertisements)
|
08-31-2013, 10:31 PM | #7 |
Senior Member
Join Date: May 2010
Location: PRINEVILLE, OR.
Posts: 490
|
Re: Update on how it is running
Thanks Ken Ct. I should have said 65 on the PV....must have been thinking MPH. LOL
__________________
KIM KARDASHIAN ISN'T FLAT, BUT MY MOTOR IS..... http://s818.photobucket.com/home/roglehr/index |
08-31-2013, 10:46 PM | #8 |
BANNED
Join Date: May 2010
Location: stratford,ct
Posts: 5,971
|
Re: Update on how it is running
No problem Roger,it just looked kind of funny.At #95 there would not be a hole.As you know bigger #'s smaller the hole. lol ken ct.Engine looks awsume.
|
09-01-2013, 08:20 AM | #9 |
Senior Member
Join Date: May 2010
Location: Gardiner Me.
Posts: 4,200
|
Re: Update on how it is running
That's the perfect street engine Roger. I build a lot just like that. Some like a milder cam so I usually use the Max-1. Walt
|
09-01-2013, 11:49 AM | #10 |
Senior Member
Join Date: May 2010
Location: PRINEVILLE, OR.
Posts: 490
|
Re: Update on how it is running
Ole Ron recommended the L100 and I like it. Drives OK for me and has a nice idle.
__________________
KIM KARDASHIAN ISN'T FLAT, BUT MY MOTOR IS..... http://s818.photobucket.com/home/roglehr/index |
|
|
Sponsored Links (Register now to hide all advertisements) |
|