Go Back   The Ford Barn > General Discussion > Model A (1928-31)

Sponsored Links (Register now to hide all advertisements)

Reply
 
Thread Tools Display Modes
Old 01-16-2022, 01:57 PM   #1
Busmoss
Member
 
Busmoss's Avatar
 
Join Date: Jan 2022
Location: Benton, KY
Posts: 32
Default Mechanical Advance distributor Identification help

I am new to Model A and B components. Unfortunately for me this distributor data plate has come off and I cant tell what I have here. I see the timing plate says autolite. The back lash and advance springs are so weak that the timing is all over the place. Is this worth fixing?
It is unorthodox, I know, and I have ordered an original manual set up. Could this style even be concidered good for an emergency spare if repaired?
Attached photos:
Attached Images
File Type: jpg IMG_0478.jpg (41.9 KB, 156 views)
File Type: jpg IMG_0479.jpg (43.1 KB, 134 views)
File Type: jpg IMG_0480.jpg (39.3 KB, 145 views)
File Type: jpg IMG_0481.jpg (38.5 KB, 127 views)
Busmoss is offline   Reply With Quote
Old 01-16-2022, 02:06 PM   #2
Bob C
Senior Member
 
Join Date: May 2010
Location: So Cal
Posts: 8,713
Default Re: Mechanical Advance distributor Identification help

Looks like a Jeep distributor, here is a picture of one I converted.
Attached Images
File Type: jpg Jeep-dist.JPG (107.9 KB, 83 views)
Bob C is offline   Reply With Quote
Sponsored Links (Register now to hide all advertisements)
Old 01-16-2022, 02:07 PM   #3
Busmoss
Member
 
Busmoss's Avatar
 
Join Date: Jan 2022
Location: Benton, KY
Posts: 32
Default Re: Mechanical Advance distributor Identification help

Quote:
Originally Posted by Bob C View Post
Looks like a Jeep distributor, here is a picture of one I converted.
There is no way I would have guessed that! Is the advance range proper? does it work for you?
Busmoss is offline   Reply With Quote
Old 01-16-2022, 02:41 PM   #4
Busmoss
Member
 
Busmoss's Avatar
 
Join Date: Jan 2022
Location: Benton, KY
Posts: 32
Default Re: Mechanical Advance distributor Identification help

Thank you Bob C for sending me down the right path! Using your lead I found another thread and some information talking about 50's Jeep CJ5 Both for A and T. Not that crazy of a thing after all but a curve ball for a new owner non the less!
Busmoss is offline   Reply With Quote
Old 01-16-2022, 03:40 PM   #5
Busmoss
Member
 
Busmoss's Avatar
 
Join Date: Jan 2022
Location: Benton, KY
Posts: 32
Default Re: Mechanical Advance distributor Identification help

New member here so I am going to go on ranting:

I like stock parts and being able to experience the now unique task of manipulating the timing while under way. I also like the idea of being able to cold crank the engine closer to TDC. However, my model B engine and set up was to be a driver car. This is a serious hobby for me and I want to drive A LOT of miles once sorted.
The Jeep mechanical distributor pictured above still seems to be a viable option. The Model A aftermarket mechanical distributors are available to order at a reasonable price. Who doesn't like options though? I just looked at a complete replacement distributor for the Jeep and it is $135 including cap etc. Could be cost savings at play here.
I am not afraid to tinker in fact I have already cast my own aluminum water pump impeller and machined new starter bushings from scratch.
I think once I have the standard part here I might rebuild this old Jeep part for fun.
Busmoss is offline   Reply With Quote
Old 01-17-2022, 01:41 PM   #6
31steve
Member
 
Join Date: Jan 2014
Location: Asheville NC
Posts: 49
Default Re: Mechanical Advance distributor Identification help

Sponsored Links (Register now to hide all advertisements)
I'm running a willys jeep distributor on my B engine and I love the way it performs. I made a timing degree marker behind the pulley and I can time it with my timing light.
Attached Images
File Type: jpg ls head on 2.jpg (80.7 KB, 94 views)
31steve is offline   Reply With Quote
Old 01-17-2022, 11:59 PM   #7
Busmoss
Member
 
Busmoss's Avatar
 
Join Date: Jan 2022
Location: Benton, KY
Posts: 32
Default Re: Mechanical Advance distributor Identification help

31steve, What advance range should one expect? Static timing degree target? I was messing with that Willys Jeep distributor today because I cant help myself. I shortened the stretched advance springs by one coil and took out the slop but have certainly changed the advance curve.
Marked my crank pulley 0, 19, and 40. Set the points to just open @19 with a buzz box as if it were a "B" distributor. It ran quite nice but if I had a closer to TDC it would probably start with less throttle.
Busmoss is offline   Reply With Quote
Old 01-18-2022, 04:40 PM   #8
31steve
Member
 
Join Date: Jan 2014
Location: Asheville NC
Posts: 49
Default Re: Mechanical Advance distributor Identification help

Busmoss, It's been a while since I set it and I will check next time I get my light out, but I think I set it at 20 degrees and it advances to 32 to 35 range. I could have set the advance higher but wanted it to start easy.
31steve is offline   Reply With Quote
Old 01-18-2022, 05:09 PM   #9
California Travieso
Senior Member
 
Join Date: Mar 2014
Location: Moreno Valley, CA
Posts: 940
Send a message via Yahoo to California Travieso
Default Re: Mechanical Advance distributor Identification help

Steve,

Is there any advantage to setting the advance higher? Is it so you can rev the engine higher or idle at higher RPM?

David Serrano
California Travieso is offline   Reply With Quote
Old 01-19-2022, 07:41 AM   #10
Busmoss
Member
 
Busmoss's Avatar
 
Join Date: Jan 2022
Location: Benton, KY
Posts: 32
Default Re: Mechanical Advance distributor Identification help

Thanks for the help!
Busmoss is offline   Reply With Quote
Old 01-19-2022, 09:22 AM   #11
nkaminar
Senior Member
 
nkaminar's Avatar
 
Join Date: Jan 2012
Location: Western North Carolina
Posts: 3,820
Default Re: Mechanical Advance distributor Identification help

The amount of advance can vary with the load, rpm, and compression ratio and other factors. There is knee in the advance curve were retarding will decrease the performance and advancing will have no effect. An experienced Model A driver will instinctively adjust the advance for different loads and rpms, and perhaps the GAV too. More modern distributors had combined centrifugal and vacuum advance to adjust for load and rpm. The modern cars have a computer that does all the thinking for you.

Too much advance can ruin the rod bearings in short order and have other detrimental effects. I like the manual distributor because that is what I am used to after 60 years of driving Model A's and I like being able to adjust the advance according to conditions.
__________________
A is for apple, green as the sky.
Step on the gas, for tomorrow I die.
Forget the brakes, they really don't work.
The clutch always sticks, and starts with a jerk.
My car grows red hair, and flies through the air.
Driving's a blast, a blast from the past.
nkaminar is offline   Reply With Quote
Old 01-21-2022, 07:23 AM   #12
updraught
Senior Member
 
updraught's Avatar
 
Join Date: Feb 2015
Location: Australia
Posts: 1,966
Default Re: Mechanical Advance distributor Identification help

With a low compression head you can advance the spark quite a bit for much better performance so long as it doesn't ping. The B engines had, I think, 19 degrees advance to start with, so long as you don't crank it by hand and risk a backfire. The spark should advance quickly as it is a low revving engine.
updraught is offline   Reply With Quote
Old 01-21-2022, 12:23 PM   #13
katy
Senior Member
 
katy's Avatar
 
Join Date: Jun 2015
Location: Red Deer, Alberta
Posts: 5,011
Default Re: Mechanical Advance distributor Identification help

There is information about using a Honda Civic distributor in this thread:
https://www.fordbarn.com/forum/showt...ivic&showall=1
__________________
If you don't hear a rumor by 10 AM, start one!.
Got my education out behind the barn!
katy is offline   Reply With Quote
Old 07-27-2022, 07:47 AM   #14
MattN
Junior Member
 
Join Date: Jul 2022
Posts: 13
Default Re: Mechanical Advance distributor Identification help

Quote:
Originally Posted by 31steve View Post
Busmoss, It's been a while since I set it and I will check next time I get my light out, but I think I set it at 20 degrees and it advances to 32 to 35 range. I could have set the advance higher but wanted it to start easy.

Steve have you had a chance to survey the Jeep Distributor timing /curve? Can you advise a model number or Jeep vintage you modified from?


Matt
MattN is offline   Reply With Quote
Reply

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump

Sponsored Links (Register now to hide all advertisements)


All times are GMT -5. The time now is 06:57 PM.