|
Sponsored Links (Register now to hide all advertisements) |
|
|
Thread Tools | Display Modes |
05-14-2020, 07:40 AM | #1 |
Senior Member
Join Date: Jul 2016
Location: Missouri
Posts: 424
|
53 flathead engine mounts
I installed my engine mounts so the open C is towards the front of the car. I made notes to this effect upon teardown. Now that my fan is too close to the radiator, I am wondering if they are installed correctly, and if it matters? The transmission mount lines up, and I don't see any slots in the transmission mount for movement front or aft. I thought I might be able to adjust the engine at the mount area, but it aint movin. Thanks
|
05-14-2020, 08:46 AM | #2 |
Senior Member
Join Date: Jul 2010
Location: Conifer, Colorado
Posts: 2,429
|
Re: 53 flathead engine mounts
Yep, "C" to the front.
|
Sponsored Links (Register now to hide all advertisements) |
|
05-14-2020, 09:53 AM | #3 |
Senior Member
Join Date: Jul 2016
Location: Missouri
Posts: 424
|
Re: 53 flathead engine mounts
|
05-14-2020, 10:11 AM | #4 |
Senior Member
Join Date: Jul 2010
Location: Conifer, Colorado
Posts: 2,429
|
Re: 53 flathead engine mounts
A couple more shots of the fan and radiator for comparison.
|
05-14-2020, 12:40 PM | #5 |
Senior Member
Join Date: Mar 2013
Location: Green Bay Wi
Posts: 400
|
Re: 53 flathead engine mounts
tommyleea on my 50 ford cpe it measures 1/2 @ the top of radiator and 3/4 inch @ the bottom they always where very close probably because they didn’t use a shoud it probably was good for the parts department to ,they could sell you a radiator and fan blade when you wrecked it
|
05-14-2020, 03:03 PM | #6 | |
Senior Member
Join Date: Jul 2016
Location: Missouri
Posts: 424
|
Re: 53 flathead engine mounts
Sponsored Links (Register now to hide all advertisements)
Quote:
|
|
05-14-2020, 05:59 PM | #7 |
Senior Member
Join Date: May 2010
Location: Auburn, MA
Posts: 2,106
|
Re: 53 flathead engine mounts
Is your radiator on the correct side of the U channel bracket?
__________________
“The technique of infamy is to start two lies at once and get people arguing heatedly over which is true.” ~ Ezra Pound |
05-14-2020, 08:02 PM | #8 |
Senior Member
Join Date: Jul 2010
Location: Conifer, Colorado
Posts: 2,429
|
Re: 53 flathead engine mounts
More pictures for comparison.
Last edited by Merc Cruzer; 05-14-2020 at 08:07 PM. |
05-14-2020, 09:39 PM | #9 |
Senior Member
Join Date: Jul 2016
Location: Missouri
Posts: 424
|
Re: 53 flathead engine mounts
|
05-15-2020, 07:05 AM | #10 |
Senior Member
Join Date: Mar 2013
Location: Green Bay Wi
Posts: 400
|
Re: 53 flathead engine mounts
don’t want to sound stupid but do all the blades touch or just one or two or maybe someone put the wrong bearing and shaft for the blade on it
|
05-15-2020, 08:12 AM | #11 |
Senior Member
Join Date: Jul 2016
Location: Missouri
Posts: 424
|
Re: 53 flathead engine mounts
Good question..The fan assembly is original..I didn't rotate it completely, because of it rubbing the radiator, but I did remove the fan assembly and double checked the blades to make sure they weren't bent.. Thanks..
|
05-15-2020, 08:14 AM | #12 |
Senior Member
Join Date: Jul 2016
Location: Missouri
Posts: 424
|
Re: 53 flathead engine mounts
What is the bolt and spring for at the bottom of the radiator support?
|
05-15-2020, 08:44 AM | #13 |
Senior Member
Join Date: Jan 2012
Location: Lyman,ME.
Posts: 2,630
|
Re: 53 flathead engine mounts
The bolt,spring and rubber pad allow movement in the front fender clip..... Mark
__________________
I'm thinkin' about crankin' My ragged ol' truck up and haulin' myself into town. Billy Joe Shaver |
05-15-2020, 05:10 PM | #14 |
Senior Member
Join Date: Jul 2010
Location: Conifer, Colorado
Posts: 2,429
|
Re: 53 flathead engine mounts
A few measurements for reference. 8 1/2" from the front of the left head, to the radiator. 5 1/2" from the back of the water pump pulley to the radiator. 4 1/2" from the back of the fan pulley to the radiator.
|
05-16-2020, 07:25 AM | #15 |
Senior Member
Join Date: Mar 2013
Location: Green Bay Wi
Posts: 400
|
Re: 53 flathead engine mounts
i suppose you don’t know if that car was ever in a wreck maybe the radiator core support is pushed back and no one ever straighten it
|
05-16-2020, 09:12 AM | #16 |
Senior Member
Join Date: Jun 2010
Location: San Antonio, Texas
Posts: 16,440
|
Re: 53 flathead engine mounts
What car or truck are we dealing with here. Ford, Mercury, or truck? They are all different.
|
|
|
Sponsored Links (Register now to hide all advertisements) |
|