|
Sponsored Links (Register now to hide all advertisements) |
|
|
Thread Tools | Display Modes |
03-12-2023, 01:26 PM | #1 |
Senior Member
Join Date: Feb 2011
Posts: 2,113
|
1933-1934 4 Cylinder Parts
There must be restorers outside of the circle of friends here on the Ford Barn with an interest in the later 4 cylinder engines.
I need a crank shaft pulley. If you can recommend another restorer with a parts cache please drop me a note. Thanks!
__________________
Tim Downtown, Ca Last edited by CA Victoria; 03-12-2023 at 01:35 PM. |
03-12-2023, 02:35 PM | #2 |
Senior Member
Join Date: Dec 2013
Location: Waxahachie, Texas
Posts: 949
|
Re: 1933-1934 4 Cylinder Parts
|
Sponsored Links (Register now to hide all advertisements) |
|
03-12-2023, 03:04 PM | #3 |
Senior Member
Join Date: Feb 2011
Posts: 2,113
|
Re: 1933-1934 4 Cylinder Parts
Many and me included did not realize that the 33-34 pulley is shorter to accommodate the short water pump used.
The pulley shown in your pictures is identified as a 28-34 pulley but is to long to use with the shorter 33-34 water pump. I am working on this for a friend, his engine is going into a 33 pickup that is disassembled.
__________________
Tim Downtown, Ca |
03-12-2023, 03:27 PM | #4 |
Senior Member
Join Date: May 2010
Location: So Cal
Posts: 8,754
|
Re: 1933-1934 4 Cylinder Parts
Here's a NOS one. $$$$$
http://www.allfordparts.com/shop/pro...&model=46-6312 |
03-12-2023, 03:42 PM | #5 |
Senior Member
Join Date: Feb 2011
Posts: 2,113
|
Re: 1933-1934 4 Cylinder Parts
$375...........That is ridiculous. Albeit he has a large inventory......he has been notoriously high priced......it appeals to those who do not know were to look or do not have time........
I have found that NOS and hard to find often equates into unrealistic prices. I have also found many NOS and hard to find parts by asking around.
__________________
Tim Downtown, Ca Last edited by CA Victoria; 03-12-2023 at 06:18 PM. |
03-12-2023, 07:38 PM | #6 |
Senior Member
Join Date: May 2010
Location: Oregon
Posts: 5,963
|
Re: 1933-1934 4 Cylinder Parts
Sponsored Links (Register now to hide all advertisements)
|
03-12-2023, 08:18 PM | #7 |
Senior Member
|
Re: 1933-1934 4 Cylinder Parts
Tim, Can you turn down a Model A pulley to shorten it to the correct length ?
|
03-12-2023, 09:32 PM | #8 |
Senior Member
Join Date: Feb 2011
Posts: 2,113
|
Re: 1933-1934 4 Cylinder Parts
No, because the pos. offset is greater on the A-B style. I located a photo of the 46-6312 pulley.
__________________
Tim Downtown, Ca Last edited by CA Victoria; 03-12-2023 at 09:38 PM. |
03-13-2023, 06:45 AM | #9 |
Senior Member
Join Date: Dec 2011
Location: Country Victoria Australia
Posts: 130
|
Re: 1933-1934 4 Cylinder Parts
I manufacture the pulley for the 33/34 4 cylinder engine out of one piece billeted steel and have them on two of my cars. If you send me an email I can send a photo of the finished product. Currently out of stock however the next batch of pulleys should be finished in two weeks . [email protected]
|
03-13-2023, 11:20 AM | #10 |
Senior Member
Join Date: May 2010
Location: So Cal
Posts: 8,754
|
Re: 1933-1934 4 Cylinder Parts
You might PM barnfind08 on the Early V8 forum on this site, he has buildings full of NOS parts. Email [email protected]
|
|
|
Sponsored Links (Register now to hide all advertisements) |
|