Go Back   The Ford Barn > General Discussion > Early V8 (1932-53)

Sponsored Links (Register now to hide all advertisements)

Reply
 
Thread Tools Display Modes
Old 01-08-2020, 09:45 PM   #1
Flathead Youngin'
Member
 
Join Date: Oct 2019
Location: Kentucky
Posts: 69
Default Can't find thread on distributor timing

There are a lot of threads on the sun machine, KR Wilson fixtures, etc. I've tried a lot of searching with various combinations of words...

There was one in particular that had some pics from a fella that showed where he had built his own timing fixture.

Point me in a direction, please, if you can recall the thread...
__________________
"Constipated, can't pass a thing! Don't laugh, bud, your daughter may be in here. They don't call 'em flyn' flatheads for nothin'!"
Hot Rod (Kennie) Holmes
Flathead Youngin' is offline   Reply With Quote
Old 01-08-2020, 09:50 PM   #2
Ziggster
Senior Member
 
Join Date: Aug 2018
Location: Ottawa, ON
Posts: 840
Default Re: Can't find thread on distributor timing

I've been searching as well. If you are talking about Bruce Lancaster's protractor method, I haven't found the actual thread either. Plenty of references to it, but no actual thread.
Ziggster is offline   Reply With Quote
Sponsored Links (Register now to hide all advertisements)
Old 01-08-2020, 09:52 PM   #3
Flathead Youngin'
Member
 
Join Date: Oct 2019
Location: Kentucky
Posts: 69
Default Re: Can't find thread on distributor timing

No, not good 'ole Bruce's, there was one where the guy built a box out of plywood, put gauges in it, etc.

I'll keep digging, too.....
__________________
"Constipated, can't pass a thing! Don't laugh, bud, your daughter may be in here. They don't call 'em flyn' flatheads for nothin'!"
Hot Rod (Kennie) Holmes
Flathead Youngin' is offline   Reply With Quote
Old 01-08-2020, 10:25 PM   #4
Ziggster
Senior Member
 
Join Date: Aug 2018
Location: Ottawa, ON
Posts: 840
Default Re: Can't find thread on distributor timing

Is this what you are looking for? Bruce mentions a battety box, socket, and flashlight bulb, but nothing else in post #4.

https://www.jalopyjournal.com/forum/...ixture.288221/
Ziggster is offline   Reply With Quote
Old 01-08-2020, 10:38 PM   #5
Flathead Youngin'
Member
 
Join Date: Oct 2019
Location: Kentucky
Posts: 69
Default Re: Can't find thread on distributor timing

Very interesting but I still can't find it. It was a thread about timing fixtures/sun machines and a fella just posted some pics of his homebrew version. He really didn't give any details except, and I searched a lot of combos of these words, "I couldn't find one for years so I just built one myself." It was quite a few years ago. I started to send the fella a PM but got side tracked and lost the open window on my desktop. I can't recall the username...
__________________
"Constipated, can't pass a thing! Don't laugh, bud, your daughter may be in here. They don't call 'em flyn' flatheads for nothin'!"
Hot Rod (Kennie) Holmes
Flathead Youngin' is offline   Reply With Quote
Old 01-08-2020, 10:39 PM   #6
Ziggster
Senior Member
 
Join Date: Aug 2018
Location: Ottawa, ON
Posts: 840
Default Re: Can't find thread on distributor timing

Sponsored Links (Register now to hide all advertisements)
I think this is it. Start at Bruce's post #83.

https://www.jalopyjournal.com/forum/....257066/page-3
Ziggster is offline   Reply With Quote
Old 01-09-2020, 12:04 AM   #7
35fordtn
Senior Member
 
35fordtn's Avatar
 
Join Date: Aug 2010
Location: McMinnville, TN
Posts: 2,327
Default Re: Can't find thread on distributor timing

I made a crude one a couple years ago for the heck of it and gave it to a friend.
I used a degree wheel that mounted to the housing and a home made needle onto a flathead adapter, light bulb some wire and a 9V battery.
I have pondered having the KRW fixture reproduced in a affordable form..

If you make one just remember the V-8's fire on 45 degrees, and these dual point distributors have ten degrees of overlap, thus you would strive for 22.5 degrees each side and 35 total. If you make one you will need to drill a hole for a pin or make a mark for the initial timing set mark. Likely you will have to borrow a KRW fixture to make that mark accurate.
35fordtn is offline   Reply With Quote
Old 01-09-2020, 12:10 AM   #8
Tinker
Senior Member
 
Tinker's Avatar
 
Join Date: May 2010
Location: MN
Posts: 7,053
Default Re: Can't find thread on distributor timing

If you have a sun machine, then I get this post.


If not, just send it to Bubba. You can send two also (I did just encase, did the same with skip, and it's on a shelf). It's really reasonable and checked out by a pro. As they say a smart man knows his limitations. if the time comes when it's not offered I'll have to do it... but I have one on the shelf, and really unless I live to 190 i'm good.


.
Tinker is offline   Reply With Quote
Old 01-09-2020, 06:45 AM   #9
Ziggster
Senior Member
 
Join Date: Aug 2018
Location: Ottawa, ON
Posts: 840
Default Re: Can't find thread on distributor timing

Different strokes for different folks. I have nothing against Bubba and others who rebuild them. It is a lot of work, and expensive speciality equipment is required to do a 100% inspection. For me it is a journey of discovery, and by researching past threads here, HAMB, and elsewhere, many seem to have had questions as to the operation of this unique device over the last twenty years. At the moment, I still plan on trying to rebuild mine, and we'll see if it works to my satisfaction, if not, then I'll send it out, or buy one that has already been done.
Ziggster is offline   Reply With Quote
Old 01-09-2020, 08:54 AM   #10
rockfla
Senior Member
 
rockfla's Avatar
 
Join Date: Mar 2014
Location: Jacksonville FL
Posts: 3,927
Default Re: Can't find thread on distributor timing

Quote:
Originally Posted by Flathead Youngin' View Post
There are a lot of threads on the sun machine, KR Wilson fixtures, etc. I've tried a lot of searching with various combinations of words...

There was one in particular that had some pics from a fella that showed where he had built his own timing fixture.

Point me in a direction, please, if you can recall the thread...
I think you are looking for "FlatHeadTed" on the "Current" thread running on "Testing Helmet on a Sun Machine".
rockfla is online now   Reply With Quote
Old 01-09-2020, 11:41 AM   #11
rotorwrench
Senior Member
 
rotorwrench's Avatar
 
Join Date: Jun 2010
Location: San Antonio, Texas
Posts: 16,371
Default Re: Can't find thread on distributor timing

They did require special adapters for some types when running them on the Sun machines.
rotorwrench is offline   Reply With Quote
Old 01-10-2020, 09:59 AM   #12
Hoop
Senior Member
 
Hoop's Avatar
 
Join Date: May 2010
Location: Jacksonville FL
Posts: 1,137
Default Re: Can't find thread on distributor timing

Sometimes if you look hard, you may find a Sun machine that you can fix up.


SunMachDirty.JPG
__________________
"Remember that when it comes to intelligence, half of all of us are below average."
Hoop is offline   Reply With Quote
Old 01-10-2020, 10:05 AM   #13
Hoop
Senior Member
 
Hoop's Avatar
 
Join Date: May 2010
Location: Jacksonville FL
Posts: 1,137
Default Re: Can't find thread on distributor timing

"They did require special adapters for some types when running them on the Sun machines."

Rotor, you are correct. Here's the Apple Peeler Adapter.

sunapple.jpg
__________________
"Remember that when it comes to intelligence, half of all of us are below average."
Hoop is offline   Reply With Quote
Old 01-10-2020, 10:42 AM   #14
philipswanson
Senior Member
 
Join Date: Oct 2015
Location: Bonita, CA
Posts: 1,374
Default Re: Can't find thread on distributor timing

Why is timing an issue? I just set up the points, make sure the advance is working and set the tab on zero on the Sun 504 machine. After installation, I advance it all the way on the tab and listen for pinging which I have never heard. If I hear it, I would just throw some premium in the mix rather than retard it. Maybe I am tone deaf to it? Runs great on either distributor I have.
philipswanson is offline   Reply With Quote
Old 01-10-2020, 10:57 AM   #15
38bill
Senior Member
 
38bill's Avatar
 
Join Date: Apr 2014
Location: Minnesota
Posts: 1,163
Default Re: Can't find thread on distributor timing

This one? See post #17

https://www.fordbarn.com/forum/showthread.php?t=56112
38bill is offline   Reply With Quote
Old 01-10-2020, 11:27 AM   #16
tubman
Senior Member
 
tubman's Avatar
 
Join Date: Dec 2013
Location: Minnesota, Florida Keys
Posts: 10,260
Default Re: Can't find thread on distributor timing

I would like to see some more information on the unit "Lawrie" built that "38bill" mentioned above.
tubman is online now   Reply With Quote
Old 01-10-2020, 03:11 PM   #17
Hoop
Senior Member
 
Hoop's Avatar
 
Join Date: May 2010
Location: Jacksonville FL
Posts: 1,137
Default Re: Can't find thread on distributor timing

DistTesterLawrie.jpg

Some beautiful work by Lawrie. Not sure if I can see a strobe display. That's pretty tricky. If you plan to try to build your own, first figure out how to make a good sharp strobe when the points OPEN.


SunMachrestore1.jpg

This is a partial restore on the Sun that I found behind a shop ... picture in the above post. If you get this far, you have it made ... the tach and dwell can easily be substituted. The strobe, main power supply, and the rotating parts are what you really want to salvage from one in poor shape.
__________________
"Remember that when it comes to intelligence, half of all of us are below average."
Hoop is offline   Reply With Quote
Old 01-10-2020, 04:34 PM   #18
35fordtn
Senior Member
 
35fordtn's Avatar
 
Join Date: Aug 2010
Location: McMinnville, TN
Posts: 2,327
Default Re: Can't find thread on distributor timing

Hoop,
I have three suns but this 500 that came from mark at paramont is the one I primarily use. It has the LED flash tube which I really like.




Sent from my iPhone using Tapatalk
35fordtn is offline   Reply With Quote
Old 01-10-2020, 08:17 PM   #19
Hoop
Senior Member
 
Hoop's Avatar
 
Join Date: May 2010
Location: Jacksonville FL
Posts: 1,137
Default Re: Can't find thread on distributor timing

Michael, that LED conversion is a pretty good piece of work. More complicated than one would think. I have spare flash tubes or would have converted.
__________________
"Remember that when it comes to intelligence, half of all of us are below average."
Hoop is offline   Reply With Quote
Old 01-10-2020, 08:45 PM   #20
Flathead Youngin'
Member
 
Join Date: Oct 2019
Location: Kentucky
Posts: 69
Default Re: Can't find thread on distributor timing

That's the one!

He PM'd me but I hadn't had a chance to dig back through his posts. I'd love to see some inside pics and a few details!

Quote:
Originally Posted by Hoop View Post
Attachment 418494

Some beautiful work by Lawrie. Not sure if I can see a strobe display. That's pretty tricky. If you plan to try to build your own, first figure out how to make a good sharp strobe when the points OPEN.
__________________
"Constipated, can't pass a thing! Don't laugh, bud, your daughter may be in here. They don't call 'em flyn' flatheads for nothin'!"
Hot Rod (Kennie) Holmes
Flathead Youngin' is offline   Reply With Quote
Reply

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump

Sponsored Links (Register now to hide all advertisements)


All times are GMT -5. The time now is 08:56 AM.