|
Sponsored Links (Register now to hide all advertisements) |
|
|
Thread Tools | Display Modes |
05-05-2019, 02:57 PM | #1 |
Senior Member
Join Date: May 2010
Location: Long Island, NY
Posts: 1,052
|
Oil Pan Dipstick Mount Repair
Is there some sort of repair for the dipstick mounting fixture that's riveted to the oil pans??
I'm looking for feedback only, not actually a way to do the repair. I'm asking because we have a 100% method for a fix leaving the OEM bracket in place (after the fix). It would attach to the pan with some 1/4-28 pan head cap screws and be removable at later time WITHOUT the pan's removal! This would allow for a gasket change if ever needed. The only single drawback is it will require welding it to the inside of the pan, this means obviously the pan has to on the bench. Thanks, Gary in N.Y. P.S. If anyone is interested in the fix (assuming we do go forward with it) we will have a few ready in a couple weeks. It will come with a pre-drilled/tapped "plate", a gasket, and the attaching screws. I have photos of the setup but can't upload them at the moment! Will do in the near future.
__________________
http://www.stromberg-bulletin.com/me...berg-equipped/ |
05-05-2019, 03:05 PM | #2 | |
Senior Member
Join Date: Sep 2011
Location: Christchurch New Zealand
Posts: 1,611
|
Re: Oil Pan Dipstick Mount Repair
Quote:
Does this involve the supply of a replacement boss for dipstick tube to screw into? I have an engine at present which has worn thread in the boss as well as loose securing rivets. Plan on removing oil pan for a permanent repair as engine is on a stand. Interested for sure. The tapped plate will be required to be welded on inside of oil pan? Yes. Phil NZ. |
|
Sponsored Links (Register now to hide all advertisements) |
|
05-05-2019, 03:12 PM | #3 |
Senior Member
Join Date: May 2010
Location: East Hartford, Ct
Posts: 5,898
|
Re: Oil Pan Dipstick Mount Repair
I did mine with a 10/32 threaded plate, tack welded to the inside of the pan. But to fix without welding or pan removal--
What I would consider is using 10/32 or 10/24 Rivnuts with the appropriate gasket to allow for the thickness of the Rivnut. Drawback--The installer would need a tool to set the nut in the sheet metal pan
__________________
DON'T RECALL DOING SOMETHING FOR MYSELF BASED ON SOMEONE ELSE'S LIKES OR DISLIKES Last edited by 51 MERC-CT; 05-06-2019 at 08:37 AM. |
05-07-2019, 11:26 AM | #4 |
Senior Member
Join Date: May 2010
Location: Long Island, NY
Posts: 1,052
|
Re: Oil Pan Dipstick Mount Repair
i brought this up again to show a few shots of what actually happens after 60 or so years to the pan and the OEM gaskets, they are very brittle when opened up. Most have a number of cracks in the gaskets.
When we figured out how to make the actual bracket for inside the pan we felt more comfortable having it fully support the outer dipstick bracket. Plus we wanted to weld it a bit further away from where the gasket rests so there wouldn't be any distortion in that area! Thanks, Gary in N.Y. P.S. Here's a few shots, showing the entire process.
__________________
http://www.stromberg-bulletin.com/me...berg-equipped/ |
05-07-2019, 11:29 AM | #5 |
Senior Member
Join Date: May 2010
Location: NJ
Posts: 6,181
|
Re: Oil Pan Dipstick Mount Repair
I am absolutely interested in his when available.
|
05-07-2019, 11:37 AM | #6 |
Senior Member
Join Date: Jun 2010
Location: San Antonio, Texas
Posts: 16,436
|
Re: Oil Pan Dipstick Mount Repair
Sponsored Links (Register now to hide all advertisements)
|
05-07-2019, 01:57 PM | #7 |
Senior Member
Join Date: Feb 2011
Posts: 794
|
Re: Oil Pan Dipstick Mount Repair
Looks like it will do the job, but good grief, what's all the weld for?
|
05-07-2019, 03:07 PM | #8 |
Senior Member
Join Date: May 2010
Location: Coral Springs FL
Posts: 10,945
|
Re: Oil Pan Dipstick Mount Repair
To hold the bottom plate permanently in correct position relative to the outer dip stick holder.
|
05-07-2019, 04:30 PM | #9 |
Senior Member
Join Date: Feb 2011
Posts: 794
|
Re: Oil Pan Dipstick Mount Repair
|
05-07-2019, 05:58 PM | #10 |
Senior Member
Join Date: Aug 2018
Location: Ottawa, ON
Posts: 855
|
Re: Oil Pan Dipstick Mount Repair
I could see rivnuts being used with the right gasket.
|
05-07-2019, 11:38 PM | #11 |
Senior Member
Join Date: Aug 2010
Location: McMinnville, TN
Posts: 2,327
|
Oil Pan Dipstick Mount Repair
This is the kit we sell for this. I always use loctite on the threads. Has the appearance of being riveted like original. I don’t see the need in having to replace that gasket often.
IMG_5012.jpg Sent from my iPhone using Tapatalk |
05-08-2019, 02:11 AM | #12 |
Senior Member
Join Date: Apr 2015
Location: Sweden
Posts: 3,045
|
Re: Oil Pan Dipstick Mount Repair
That´s the way i do it to...looks nice an only need to change it is when restoring the pan.
I just peen it a bit backing it with a piece of copper to avoid damaging the head. |
05-08-2019, 04:32 AM | #13 | |
Senior Member
Join Date: Jan 2012
Location: New Jersey
Posts: 1,425
|
Re: Oil Pan Dipstick Mount Repair
Quote:
|
|
05-08-2019, 05:32 AM | #14 |
Senior Member
Join Date: May 2015
Location: Frelighsburg, QC
Posts: 166
|
Re: Oil Pan Dipstick Mount Repair
I’ll buy one of those kits Gary, whenever they’re ready for prime time.
Sent from my iPhone using Tapatalk |
05-08-2019, 08:57 AM | #15 |
Senior Member
Join Date: May 2010
Location: Coral Springs FL
Posts: 10,945
|
Re: Oil Pan Dipstick Mount Repair
Oh my goodness! Looks to me like the welding holds the bracket inside the pan PERMANENTLY (like in forever) in position so that the screws can be removed and replaced without the internal bracket falling into the oil pan. Seems like a good idea to me as you don't have to worry about any nuts or rivets coming loose. Locktite is your friend. |
05-08-2019, 09:06 AM | #16 |
Senior Member
Join Date: May 2010
Location: Eagle River,Alaska
Posts: 353
|
Re: Oil Pan Dipstick Mount Repair
Gary, I would be interested in a couple of those.
|
05-08-2019, 09:33 AM | #17 | |
Senior Member
Join Date: Feb 2011
Posts: 794
|
Re: Oil Pan Dipstick Mount Repair
Quote:
Take a look at post #3 above. |
|
05-08-2019, 11:45 AM | #18 | |
Senior Member
Join Date: May 2010
Location: Long Island, NY
Posts: 1,052
|
Re: Oil Pan Dipstick Mount Repair
Quote:
When we begin to make these available the amount of welding would be up to the welder, simple. It doesn't take much to keep the plate in position. Thanks, Gary in N.Y. P.S. To Joe above, I don't believe there will be any clearance issues with the internals but it will get checked. Your pan will be done identical to the one in the photo above! My friend has your pan for the straps also, however he will be gone for a few weeks?
__________________
http://www.stromberg-bulletin.com/me...berg-equipped/ |
|
05-08-2019, 01:00 PM | #19 | |
Senior Member
Join Date: May 2010
Location: Coral Springs FL
Posts: 10,945
|
Re: Oil Pan Dipstick Mount Repair
Quote:
Those 2 short MIG weld beads on the outside of the "V" plate are not a lot of welding, IMO. Much better than just a wimpy tack weld. Better safe than sorry. |
|
05-09-2019, 05:24 AM | #20 | |
Senior Member
Join Date: Jan 2012
Location: New Jersey
Posts: 1,425
|
Re: Oil Pan Dipstick Mount Repair
Quote:
|
|
|
|
Sponsored Links (Register now to hide all advertisements) |
|