|
Sponsored Links (Register now to hide all advertisements) |
|
|
Thread Tools | Display Modes |
08-29-2014, 07:51 AM | #41 |
Senior Member
Join Date: Jun 2010
Location: New Jersey
Posts: 1,471
|
Re: Diode across coil?
See this is what I don't understand and is what spawned this conversation.
Why doesn't a solid state ignition need a capacitor in series with the coil if it is indeed an tank circuit? If it is a tank circuit the cap would be needed no matter what the switching device is, no? Unless of course modern coils have a cap built in which I suppose is possible but I'd expect it to be listed on schematics then as well. |
08-29-2014, 08:35 AM | #42 |
Senior Member
Join Date: May 2010
Location: Cape Cod
Posts: 1,128
|
Re: Diode across coil?
MrTube.....
Lets try another approach : 1. When the points close, the current in the coil's primary creates a large magnetic field. 2. When the points open, this magnetic field collapses since their is no current to keep it present. 3. When a magnetic field collapses, the changing amount of magnetic field creates a current in the secondary and because the number of turns of wire is large, a large voltage is produced in the secondary. The amount of voltage is related to the rate that the field collapses and the number of turns of wire...so you want a fast collapsing field. 4. When the points open, the current that was going into the coil from the battery wants to continue to flow...this is called inductance. Since the current tries to keep flowing when the points open, a spark will form which is the current trying to keep flowing. 5. The resulting spark at the points is wasted energy that could have been in the collapsing field, thus the spark at the spark plug is weak. 6. If a cap is placed at the points, then the current that was trying to flow by jumping across the points is diverted into the cap. After a very short time, the energy in the cap flows back out into the coil and boosts the collapsing field, thus increasing the spark at the spark plug. 7. Moving the cap from the points changes this flow of energy from the points to the cap and back to the coil. 8. It's not really a "tuned circuit" in the RF sense, but it's like a tuned circuit. 9. If a diode is uses instead of a cap, then when the points open, the energy from the current trying to keep flowing (inductance) will flow into the diode and become heat and you will have a poorer spark than you would have with a cap. Marc Last edited by marc hildebrant; 08-29-2014 at 08:43 AM. |
Sponsored Links (Register now to hide all advertisements) |
|
08-29-2014, 08:59 AM | #43 | |
Senior Member
Join Date: Jun 2010
Location: New Jersey
Posts: 1,471
|
Re: Diode across coil?
Quote:
I'm understanding that part. Now I'm confused as to why it looks like modern ignitions do not have a cap in that section of the circuit. Perhaps either it's built into the coil and we aren't seeing it, or the schematics are wrong? Or, maybe the coils just have far more turns and the switching device can handle a lot more current than points? |
|
08-29-2014, 09:23 AM | #44 | |
Senior Member
Join Date: May 2010
Location: Windy City
Posts: 2,919
|
Re: Diode across coil?
Quote:
A solid state system without L-C produces a much shorter duration spark, as there is no coil current resonance after the initial mag field collapse. Most transistor switched ignitions do not employ the capacitor because a discharged cap would momentarily present itself as a direct current short when the transistor switches 'on' (points close). The instantaneous initial high current surge into the cap would damage the transistor junction. |
|
08-29-2014, 09:35 AM | #45 | |
Senior Member
Join Date: Jun 2010
Location: New Jersey
Posts: 1,471
|
Re: Diode across coil?
Quote:
Ah! I wish this forum had a "like" button cause that was a perfect explanation. Thanks Mike! |
|
08-30-2014, 09:34 AM | #46 |
Junior Member
Join Date: Feb 2013
Posts: 7
|
Re: Diode across coil?
Sponsored Links (Register now to hide all advertisements)
Bottom line is that with a mechanical switch on a Kettering ignition you need the condenser (capacitor) to allow the points to get far enough open to prevent arcing as the primary voltage rises to ~150 volts. Introducing this capacitor does effect the circuit but is only required due to the contacts needing a head start. With an electronic switch no capacitor is typically used. I wonder if Charles's experience at NCR on electric typewriters might have inspired his ignition. He would have faced the challenge of despiking the solenoids that did the typing work? |
08-30-2014, 05:29 PM | #47 | |
Senior Member
Join Date: May 2010
Location: Windy City
Posts: 2,919
|
Re: Diode across coil?
Quote:
Wow, that schematic shows how things have progressed. 1996 tech and a Darlington output! Today the coil drivers are all MOSFET. |
|
08-31-2014, 05:21 AM | #48 | |
Senior Member
Join Date: Jul 2010
Location: United Kingdom
Posts: 1,443
|
Re: Diode across coil?
Quote:
I've run my As with the capacitor on the firewall for decades. Electronic/magnetic fields move at very approx 1/10 speed of light . work the maths out for a couple of extra feet of wiring if you're so inclined. ( Ditto HT leads from plugs to distributor!) |
|
08-31-2014, 08:22 AM | #49 | |
Senior Member
Join Date: Jun 2010
Location: New Jersey
Posts: 1,471
|
Re: Diode across coil?
Quote:
As I said previously it's these kind of assumptions that cannot be made. Many many electronic circuits even a thousandth of an inch can matter. No, it probably doesn't matter in this circuit, but just going by what speed things move at isn't something you can base an assumption on. If you add a half inch to one of the traces in your mobile phone there is a good chance it would no longer work, at all. |
|
|
|
Sponsored Links (Register now to hide all advertisements) |
|