|
Sponsored Links (Register now to hide all advertisements) |
|
|
Thread Tools | Display Modes |
01-17-2019, 10:12 PM | #1 |
Senior Member
Join Date: Jun 2017
Posts: 104
|
Mig welder question
I talked to a few friend with Migs and figured out that mine has a non adjustable gas regulator and theres all have an adjustable regulator. Will and adjustable regulator be worth the cost?I have a Hobart 110 volt mig that I bought many years back. Never used enough to get good at it. Dug it out and been using it on some sheet metal repair on a '65 Mustang. Still not realy getting the hang of it. So should I try an adjustable regulator?
|
01-17-2019, 10:15 PM | #2 |
Junior Member
Join Date: Jul 2017
Location: N/W Indiana
Posts: 26
|
Re: Mig welder question
Personally I would, being someone who used to do X-ray quality welds as well a lots of sheet metal work the proper gas flow is essential for a quality weld.
Do you know what cfm it’s flowing at? Sent from my iPhone using Tapatalk |
Sponsored Links (Register now to hide all advertisements) |
|
01-17-2019, 10:16 PM | #3 |
Junior Member
Join Date: Jul 2017
Location: N/W Indiana
Posts: 26
|
Re: Mig welder question
If there is not sufficient gas flow, it may be one of your issues of not getting the hang of it
Sent from my iPhone using Tapatalk |
01-17-2019, 10:25 PM | #4 |
Senior Member
Join Date: May 2010
Location: Lancaster, CA
Posts: 916
|
Re: Mig welder question
The expense of a regulator is nominal compared to the increased quality it will provide your welds... buy it and install it as soon as possible
__________________
Lancaster, California Visit hotrodreverend.com to view hundreds of pictures and videos of the build of the 1955 Ford Club Sedan! |
01-17-2019, 11:37 PM | #5 |
Senior Member
Join Date: Jun 2017
Posts: 104
|
Re: Mig welder question
Thats what I've been thinking. $30-&35 on Amazon shipped to my door by Wedensday. Think I will just bite the bullet and go ahead and order one.
|
01-17-2019, 11:47 PM | #6 |
Junior Member
Join Date: Jul 2017
Location: N/W Indiana
Posts: 26
|
Re: Mig welder question
Sponsored Links (Register now to hide all advertisements)
Sent from my iPhone using Tapatalk |
01-18-2019, 01:14 AM | #7 |
Member
Join Date: Jul 2018
Posts: 97
|
Re: Mig welder question
I've just gone through the process of setting up a mig for sheet metal work. Getting the Gas flow right helped some. Get some off cuts and setup on a bench to get it dialed in.
Make sure you are getting enough heat into the weld for penetration. You'll need a tack setting and a welding setting. I find a tack setting has high voltage and lower wire speed and my weld setting is higher wire speed and lower voltage. Gas CFM for me is anywhere between 10-15 litres per minute. I turn it up when I'm linishing the weld and there are defects in it. I find with welding sheet metal it helps to stop and let the area cool off in short bursts. Zap and watch the colour of the surrounding metal when it gets red hold let it cool off and go again. I end up over lapping little C shaped welds. This way you can get heat in to get penetration but not too much heat that you end up blowing holes. Practice makes perfect. Cut some scraps up and practice on the bench. |
01-18-2019, 11:34 AM | #8 |
Senior Member
Join Date: May 2010
Location: St. Michael, Minnesota
Posts: 1,713
|
Re: Mig welder question
My wire welder came with an adjustable flow regulator with no gauge. I put the tip next to my ear and pull the trigger to hear gas rushing, then regulate to a medium hiss. On my welder, I could never use fine wire, but I did rather well with .033 or .035. Like the guy above said, weld things that don't need welding to stay in practice.
|
01-18-2019, 12:39 PM | #9 |
Junior Member
Join Date: Jul 2017
Location: N/W Indiana
Posts: 26
|
Re: Mig welder question
Oh, another thing. The cleaner the materials the better, I clean my mig joints as good as I do my tig joints. Those processes are not as forgiving as smaw
Sent from my iPhone using Tapatalk |
01-18-2019, 01:27 PM | #10 |
Senior Member
Join Date: Oct 2011
Location: Indiana
Posts: 114
|
Re: Mig welder question
Rusty welding wire can mess things up. Often a hidden culprit.
|
01-18-2019, 02:41 PM | #11 |
Senior Member
Join Date: May 2010
Posts: 1,770
|
Re: Mig welder question
what gas are you using it,s important
|
01-19-2019, 01:08 PM | #12 |
Senior Member
Join Date: May 2010
Location: Springboro. Ohio
Posts: 212
|
Re: Mig welder question
You should be using Argon-25% CO2......Bob L
|
01-20-2019, 12:15 PM | #13 |
Senior Member
Join Date: May 2010
Location: St. Michael, Minnesota
Posts: 1,713
|
Re: Mig welder question
Reread post number nine. I have a book on weekend welding, for hot rods, race cars, and airplanes. The guys tig welding often wipe down the rod with acetone before welding. The book also said to always weld down. If you need to weld it, turn it upside down if you have to, but always weld down.
|
01-20-2019, 01:06 PM | #14 |
Senior Member
Join Date: Mar 2018
Location: Arkansas
Posts: 525
|
Re: Mig welder question
What is welding down?
|
01-20-2019, 02:51 PM | #15 |
Senior Member
Join Date: Aug 2012
Location: Abq, NM
Posts: 3,607
|
Re: Mig welder question
|
01-20-2019, 02:52 PM | #16 |
Junior Member
Join Date: Jul 2017
Location: N/W Indiana
Posts: 26
|
Re: Mig welder question
Yea I think he was referring to vertical down
Sent from my iPhone using Tapatalk |
01-21-2019, 12:38 AM | #17 |
Senior Member
Join Date: Jun 2017
Posts: 104
|
Re: Mig welder question
Got regulator from Amazon. Played with flow adjustment. Better. Watche a couple of vidios. Discovered that the gas shield on the torch tip was not adjusted properly. That helped. Vidio guy said the ground clamp on my Hobart was junk. Suggested replacing it or wraping it with braided copper wire. Did that. It helped. Still need more practice but it is working much better now. I am using Argon/Co2 mix. Also adjusted my helmet to the lightest setting. I can see better now which also helps. Regulaor was $25 from Amazon with glass sight tube with a steel ball in it. Decent quality and seems to work just fine.
|
01-21-2019, 01:20 AM | #18 |
Junior Member
Join Date: Jul 2017
Location: N/W Indiana
Posts: 26
|
Re: Mig welder question
Good to hear it’s running better
Sent from my iPhone using Tapatalk |
01-24-2019, 12:20 PM | #19 |
Senior Member
Join Date: Oct 2015
Location: s/w Iowa
Posts: 111
|
Re: Mig welder question
I found that with my rather cheap wire feed welder, it works better on sheetmetal to "push" the stinger rather than the conventional method of pulling. I am able to see what the weld is actually doing this way.
|
|
|
Sponsored Links (Register now to hide all advertisements) |
|