|
03-29-2020, 03:12 PM | #1 |
Senior Member
Join Date: Jul 2018
Location: Spring Grove, Illinois
Posts: 1,371
|
Loose Rod
I am re assembling an engine that has been rebuilt and I have a problem. After applying 50 pounds of torque, the rod is still loose on the crankshaft. This is with new rods and insert bearings. No shims. Was the crankshaft ground too far?
__________________
"The more things change, the more they stay the same." |
03-29-2020, 03:52 PM | #2 |
Senior Member
Join Date: May 2010
Location: on the Littlefield
Posts: 6,159
|
Re: Loose Rod
If you don't have measuring tools Use aluminum foil--- figure how many layers lock it up--try the rod and bearing on a different journal see if it fits different -
Guess I should have asked which way it is "loose", it should move side to side a little--- but if it rattles around in every direction--- and check the bearing inserts for the size or other numbers and look at the others to see if the same |
Sponsored Links (Register now to hide all advertisements) |
|
03-29-2020, 03:52 PM | #3 |
Senior Member
Join Date: May 2010
Location: Largo Florida
Posts: 7,225
|
Re: Loose Rod
Whats the clearance ? Thats a must know.
|
03-29-2020, 04:15 PM | #4 |
Senior Member
Join Date: Jul 2018
Location: Spring Grove, Illinois
Posts: 1,371
|
Re: Loose Rod
I was having too much rotational play on the crankshaft. I took the rod off of #1 and switched it with #4, and now it fits better on that one. But I tried the rest of them out and they have the opposite problem of being too tight. Guess I have to get shims now for the other three?
__________________
"The more things change, the more they stay the same." |
03-29-2020, 04:21 PM | #5 |
Senior Member
Join Date: May 2010
Location: Oregon
Posts: 5,966
|
Re: Loose Rod
Why are you into this block? What is the rebuilders opinion? Is not 50# on the rod nuts a bit much?
|
03-29-2020, 04:38 PM | #6 |
Senior Member
Join Date: May 2010
Location: So Cal
Posts: 8,755
|
Re: Loose Rod
Sponsored Links (Register now to hide all advertisements)
Bob |
03-29-2020, 05:22 PM | #7 |
Senior Member
Join Date: Jul 2018
Location: Spring Grove, Illinois
Posts: 1,371
|
Re: Loose Rod
I should not have said rebuilt. I had the block machined and parts purchased. Reccommended torque on the rods is 45 pounds.
How else can I loosen a rod up?
__________________
"The more things change, the more they stay the same." |
03-30-2020, 09:43 AM | #8 | |
Senior Member
Join Date: Jun 2010
Location: 34.22 N 118.36 W
Posts: 1,057
|
Re: Loose Rod
Quote:
One problem I have had with inserts are interference with the radius ground on the crank journal. It is pretty easy to identify when you are looking for it. If this is the case, a bearing scraper can be used to relieve the edge where it is riding on the radius. It also sounds like the crank may have been ground with different size journals. While this may sound like a hack job, it may have just been repair work over its life. Do you have a tool, (caliper or micrometer) to measure the journals? J
__________________
As Carroll Smith wrote; All Failures are Human in Origin. |
|
03-29-2020, 05:53 PM | #9 |
Senior Member
Join Date: Jun 2010
Location: San Antonio, Texas
Posts: 16,440
|
Re: Loose Rod
You have a problem there. Insert bearings are available in standard and plus sizes to fit known crankshaft crank pin journal diameters. The crank pin journals need to be measured with a micrometer to see if they are close to some standard or oversize diameter. The bearings inserts should be of a known inside diameter and fit snug to the con rod big end with the locking tabs in their respective grooves. Plastigauge can be used to check clearances. Bearing shells should be marked for part number and size on the back of each shell. Check all this yourself or contact the shop that did the work for help.
The crankshaft may need some time in a crank grinding machine if the sizes don't match up. Only a poured babbitt block & connecting rods need shims. |
03-30-2020, 12:48 AM | #10 | |
Senior Member
Join Date: Jun 2014
Location: Melbourne, Australia
Posts: 7,497
|
Re: Loose Rod
Quote:
This is a common and puzzling error made in parts catalogues and repair manuals that I have seen.
__________________
I'm part of the only ever generation with an analogue childhood and a digital adulthood. |
|
03-29-2020, 06:59 PM | #11 |
Senior Member
Join Date: May 2010
Location: Oregon
Posts: 5,966
|
Re: Loose Rod
When they machined the block did they have the parts to gauge?
|
03-29-2020, 08:51 PM | #12 |
Senior Member
Join Date: Jul 2018
Location: Spring Grove, Illinois
Posts: 1,371
|
Re: Loose Rod
Yes they had all of the parts. They are a pretty reputable shop around here, they know Model A's. Which is why it is odd to me. So my inserts for the rods might be too large?
__________________
"The more things change, the more they stay the same." |
03-30-2020, 12:12 AM | #13 |
BANNED
Join Date: Dec 2019
Posts: 1,196
|
Re: Loose Rod
Hydrodynamic principal is .001 clearance for each inch of shaft diameter..on a model a engine the correct oil clearance is .0015,regardless of the bearing used,insert or poured.Fit your connecting rods to this standard.Shortcuts are not the formula for bearing life.
|
03-30-2020, 06:30 AM | #14 |
Senior Member
Join Date: May 2010
Location: Jordan, MN
Posts: 1,411
|
Re: Loose Rod
I have assembled upwards of 180 engines with inserted rods supplied by Antique Engine Rebuilding (AER) and of those, I have run about 100 of them on an engine dyno to break them in. What I have learned from this work is that rod clearances need to be between .0015" and .0018" based on the methods I use to check assembly clearances. Much over .0018" and a slight rod knock may start after 2 hours of running/break-in. With over .002" clearance it is most likely to develop a knock during the break-in. I have not tried less than .0015" during assembly and at that clearance, I have not had a bearing failure due to lack of oil clearance at a rod bearing.
The suggested final rod bolt torque is 35# for AER and Snyder's insert bearing rods. If torquing to 45# there is a risk of twisting/distorting the rod cap. This twisted condition may also cause a rod knock. When checking rod journal diameter during assembly, I find that a mid-range journal size within the rod and bearing manufacturer's stated spec. provides the clearances I am looking for. For loosening the fit on the tight rods, I suggest taking the crankshaft to a crankshaft grinder and have them polish the journals until you obtain the proper fit. Most shops will have a motor driven abrasive belt polisher to complete this adjustment. I have had this process done a couple times prior to purchasing equipment for my Sunnen precision pin hone to adjust the fit. I hope it all works out well for you. Good Day! Last edited by Dave in MN; 03-31-2020 at 07:42 AM. |
03-30-2020, 07:56 AM | #15 |
BANNED
Join Date: Dec 2019
Posts: 1,196
|
Re: Loose Rod
Hydrodynamic lubrication is used on all types of machinery,its the basis for lubricating internal combustion engine shafts,pressurized or gravity system,insert or poured bearings,high or low compression just about every engine runs on a thin film of oil. Whats interesting to me is its a standard measurement,.001 clearance per inch of shaft diameter..run a 10 inch crankshaft journal? its hydrodynamically supported by .010 film of oil.This is where folks get confused with journals and bearing sizes and all kinds of hoohah about engine oil...get .0015 with a model a rod and it will live a long life,use an engine oil with high load and shear characteristics to protect the film.Diesel grade engine oils have these additives. If the bore is cut correctly and the crankshaft and bearings are fit to .0015 on your rods you are golden.If you can shim your insert bearings to achieve .0015 youre golden...yep,the golden rule doesnt change..fire your machinist? maybe but you can make a tight insert work with fitted shims |
03-30-2020, 01:23 PM | #16 |
Senior Member
Join Date: May 2010
Location: new britain,ct 06052
Posts: 9,390
|
Re: Loose Rod
Have you talked to the shop that did the work??
Paul in CT |
03-30-2020, 04:16 PM | #17 |
Senior Member
Join Date: Jul 2018
Location: Spring Grove, Illinois
Posts: 1,371
|
Re: Loose Rod
I do need to bring out the micrometers and do some measuring. Discovered the bearings are .030, and this is on new AER rods.
I have not talked to the shop yet. I want to try and solve this on my own, but it is looking like maybe not. I have some shims coming on the way as an option.
__________________
"The more things change, the more they stay the same." |
04-02-2020, 12:03 PM | #18 | |
Senior Member
Join Date: May 2010
Location: Jordan, MN
Posts: 1,411
|
Re: Loose Rod
Quote:
Guys: Look at his post above. He states he is using AER (Antique Engine Rebuilding) rods. If these rods and inserts were purchased within the last 8 years, the inserts are not tri-metal. They consist of a steel shell with bearing grade aluminum applied. The aluminum is quite thick when compared to the last layer of a typical tri-metal bearing. The rod bolt spec for torque on an AER rod is 35#. I recall from his earlier post that he was torquing to 45#. (50# in one case.) If he is torquing to 45#, he could be twisting the cap and binding the bearing... "More" is not "better" when torquing to a manufacturer's spec. I have used lots of the rods and inserts from AER and they have all been consistent in sizing. ("Lots" equals over 180 sets...that's over 720 rods and insert shells) Given he changed a loose rod to a different journal and it corrected the problem...either his method of assembly has changed or the diameter of the rod journals vary. Or am I missing something here? I still suspect the rod journal diameter is not consistent. Follow-up: I just saw his follow-up posted while I was typing this. He had the rod caps interchanged. Problem solved. Good! But...I still suspect the rod journal diameter is not consistent. Good Day! Last edited by Dave in MN; 04-02-2020 at 12:41 PM. |
|
03-30-2020, 04:48 PM | #19 |
Senior Member
Join Date: May 2010
Location: So Cal
Posts: 8,755
|
Re: Loose Rod
|
03-30-2020, 05:11 PM | #20 |
Senior Member
Join Date: Jul 2018
Location: Spring Grove, Illinois
Posts: 1,371
|
Re: Loose Rod
I bought laminated shims from Brattons.
https://www.brattons.com/brass-conne...rod-shims.html
__________________
"The more things change, the more they stay the same." |
|
|
Sponsored Links (Register now to hide all advertisements) |
|