Go Back   The Ford Barn > General Discussion > Early V8 (1932-53)

Sponsored Links (Register now to hide all advertisements)

Reply
 
Thread Tools Display Modes
Old 12-05-2020, 10:53 AM   #1
1stford
Senior Member
 
1stford's Avatar
 
Join Date: Sep 2016
Posts: 274
Default Engine Steady Rods

I’m doing a bit of research I’ve learned that my 36 truck would have had engine steady rods connecting the bell housing to the frame to keep it from moving. I have an 8BA in the 36 and understand those original 36 rods may not fit. Anyone have brackets that would support that and take the place of the steady rods? Maybe a templet for making my own and where to connect that?

Thanks.
1stford is offline   Reply With Quote
Old 12-05-2020, 11:12 AM   #2
deuce_roadster
Senior Member
 
deuce_roadster's Avatar
 
Join Date: Oct 2011
Location: Shelton, WA
Posts: 3,777
Default Re: Engine Steady Rods

Without the torque tube pushing forward the stay rods were eliminated when they went to the open driveline. With all the 8ba engines in 48 and earlier cars I am sure someone will have a template. Probably somebody made them commercially back in the day.
deuce_roadster is offline   Reply With Quote
Sponsored Links (Register now to hide all advertisements)
Old 12-05-2020, 11:44 AM   #3
Bob C
Senior Member
 
Join Date: May 2010
Location: So Cal
Posts: 8,711
Default Re: Engine Steady Rods

Check out this link. https://www.fordbarn.com/forum/showt...t=chatter+rods
Attached Images
File Type: jpg engine radius rods 001.jpg (64.2 KB, 128 views)
Bob C is offline   Reply With Quote
Old 12-05-2020, 12:07 PM   #4
19Fordy
Senior Member
 
19Fordy's Avatar
 
Join Date: May 2010
Location: Coral Springs FL
Posts: 10,872
Default Re: Engine Steady Rods

Here's some solid gold info. on anti chatter rods on an 8BA. Do a search on "anti chatter rods" for more.
https://www.fordbarn.com/forum/showt...engine+40+ford

https://www.fordbarn.com/forum/showt...tichatter+rods

https://www.fordbarn.com/forum/showt...i+chatter+rods

https://www.fordbarn.com/forum/showt...i+chatter+rods

https://www.fordbarn.com/forum/showt...i+chatter+rods

Last edited by 19Fordy; 12-05-2020 at 12:13 PM.
19Fordy is offline   Reply With Quote
Old 12-05-2020, 01:08 PM   #5
Merc Cruzer
Senior Member
 
Merc Cruzer's Avatar
 
Join Date: Jul 2010
Location: Conifer, Colorado
Posts: 2,420
Default Re: Engine Steady Rods

Are they something like these?
Attached Images
File Type: jpg FordFlathead154.jpg (57.2 KB, 101 views)
File Type: jpg FordFlathead155.jpg (34.2 KB, 596 views)
File Type: jpg FordFlathead162.jpg (59.4 KB, 73 views)
File Type: jpg FordFlathead163.jpg (49.6 KB, 75 views)
File Type: jpg FordFlathead164.jpg (35.4 KB, 74 views)
File Type: jpg FordFlathead011.jpg (85.6 KB, 68 views)
File Type: jpg FordFlathead055.jpg (70.9 KB, 74 views)
Merc Cruzer is online now   Reply With Quote
Old 12-05-2020, 01:43 PM   #6
1stford
Senior Member
 
1stford's Avatar
 
Join Date: Sep 2016
Posts: 274
Default Re: Engine Steady Rods

Sponsored Links (Register now to hide all advertisements)
Quote:
Originally Posted by Merc Cruzer View Post
Are they something like these?

I believe those are the rods, or something like what I need. The engine is in the truck and I’m not interested in pulling it out. It appears that I don’t have any holes there, that don’t already have a bolt in them, that I can push a rod through.
1stford is offline   Reply With Quote
Old 12-05-2020, 02:14 PM   #7
Merc Cruzer
Senior Member
 
Merc Cruzer's Avatar
 
Join Date: Jul 2010
Location: Conifer, Colorado
Posts: 2,420
Default Re: Engine Steady Rods

That was an engine I picked up, real cheap, to tear apart and then reassemble, basically to learn on, before I bought my 53' Merc.
Merc Cruzer is online now   Reply With Quote
Old 12-05-2020, 02:28 PM   #8
tubman
Senior Member
 
tubman's Avatar
 
Join Date: Dec 2013
Location: Minnesota, Florida Keys
Posts: 10,259
Default Re: Engine Steady Rods

Quote:
Originally Posted by Bob C View Post
These look good to me.
tubman is offline   Reply With Quote
Old 12-05-2020, 02:36 PM   #9
1stford
Senior Member
 
1stford's Avatar
 
Join Date: Sep 2016
Posts: 274
Default Re: Engine Steady Rods

Quote:
Originally Posted by tubman View Post
These look good to me.
When I 1st looked at these this morning it appeared that they would not work because I don't have a hole to put them through. After looking again it appears there is a bracket with the rods that bolt on to create that hole. If that's the case then that would be perfect!

Thank you everyone.
1stford is offline   Reply With Quote
Old 12-05-2020, 07:50 PM   #10
19Fordy
Senior Member
 
19Fordy's Avatar
 
Join Date: May 2010
Location: Coral Springs FL
Posts: 10,872
Default Re: Engine Steady Rods

1st ford:

To install anti chatter rods on the 8BA in my 40 Ford I welded ears with bolt holes onto the steel bell housing. Then, made rods top fit. Be sure to make sure that your clutch and brake pedal don't interfere with the steady rods after installing. Use double nuts and flat washers, not lock washers. "Tack weld" the ears for a trial fit. The ears are 1 inch thick square steel. You can use the OEM steady rods if you modify them.
Attached Images
File Type: jpg IMG_8903b.jpg (76.5 KB, 299 views)
File Type: jpg IMG_8918b.jpg (80.3 KB, 273 views)

Last edited by 19Fordy; 12-05-2020 at 08:02 PM.
19Fordy is offline   Reply With Quote
Old 12-06-2020, 01:29 AM   #11
V8COOPMAN
Senior Member
 
V8COOPMAN's Avatar
 
Join Date: May 2010
Location: East Shore of LAKE HOUSTON
Posts: 11,106
Default Re: Engine Steady Rods

.

This is a great thread with some really wonderful information AND pictures, not to mention the links to MORE info. And I'm NOT here to bring an 'off topic' into this thread, but one of the pictures above in post #5 IMMEDIATELY made me think of a picture that many of you have seen me post in the past of what CAN happen when hanging an early ('32-'48) block on an engine stand in the conventional manner......by the extended BELLHOUSING. That bell casting is quite thin, and susceptible to cracking and dropping your "NOW-junk" flathead to the floor. By comparing these two pictures, you can now see exactly how the RED engine was bolted to the stand, using the two upper, center bolt holes. That is exactly where it cracked....just barely outside the hole on the driver side of casting. This should serve to at least suggest that my first picture of the RED engine is not a fake break, resulting from some other mishap. DD









........
__________________
Click Links Below __


'35-'36 W/8BA & MECHANICAL FAN


T5 W/TORQUE TUBE
V8COOPMAN is offline   Reply With Quote
Old 12-06-2020, 08:22 AM   #12
19Fordy
Senior Member
 
19Fordy's Avatar
 
Join Date: May 2010
Location: Coral Springs FL
Posts: 10,872
Default Re: Engine Steady Rods

WOW! Thanks V8 for posting that broken bell housing photo.
Kind of sticks in your mind once you see it.
19Fordy is offline   Reply With Quote
Old 12-06-2020, 10:44 AM   #13
JSeery
Member Emeritus
 
JSeery's Avatar
 
Join Date: Nov 2012
Location: Wichita KS
Posts: 16,132
Default Re: Engine Steady Rods

The brackets like BobC posted should be fairly easy to fab or have fab'ed. They do not mount flush to the block. The ones Bob posted used different size spacers, the mounts themselves can also be machined to fit (like the ones posted).

Also, the photos of the mounts with the spacers have a modified steady rod, it threaded further down the rod and a nut used in place of the forged flare on the originals. My guess would be they ground or machined the flare off of the steady rods and then extended the threads. That would make the length of the steady rod from the frame mount to the mount easier to deal with.
Attached Images
File Type: jpg 017.jpg (69.7 KB, 65 views)
File Type: jpg 018.jpg (74.9 KB, 59 views)
File Type: jpg 019.jpg (64.2 KB, 54 views)
File Type: jpg engine radius rods 001.jpg (64.2 KB, 60 views)
File Type: jpg engine radius rods 002.jpg (51.5 KB, 57 views)

Last edited by JSeery; 12-06-2020 at 10:53 AM.
JSeery is offline   Reply With Quote
Old 12-06-2020, 12:20 PM   #14
Merc Cruzer
Senior Member
 
Merc Cruzer's Avatar
 
Join Date: Jul 2010
Location: Conifer, Colorado
Posts: 2,420
Default Re: Engine Steady Rods

Quote:
Originally Posted by V8COOPMAN View Post
.

This is a great thread with some really wonderful information AND pictures, not to mention the links to MORE info. And I'm NOT here to bring an 'off topic' into this thread, but one of the pictures above in post #5 IMMEDIATELY made me think of a picture that many of you have seen me post in the past of what CAN happen when hanging an early ('32-'48) block on an engine stand in the conventional manner......by the extended BELLHOUSING. That bell casting is quite thin, and susceptible to cracking and dropping your "NOW-junk" flathead to the floor. By comparing these two pictures, you can now see exactly how the RED engine was bolted to the stand, using the two upper, center bolt holes. That is exactly where it cracked....just barely outside the hole on the driver side of casting. This should serve to at least suggest that my first picture of the RED engine is not a fake break, resulting from some other mishap. DD









........
I always put a 2X4 under the front, behind the pulley. Maybe not the best, but I do acknowledge the risk of not supporting the front of the engine on a stand. Good reminder though.
Attached Images
File Type: jpg FordFlathead150.jpg (73.0 KB, 17 views)
File Type: jpg FordFlathead151.jpg (57.2 KB, 17 views)
File Type: jpg FordFlathead152.jpg (52.6 KB, 15 views)
File Type: jpg FordFlathead153.jpg (52.1 KB, 18 views)
Merc Cruzer is online now   Reply With Quote
Old 12-06-2020, 12:43 PM   #15
1stford
Senior Member
 
1stford's Avatar
 
Join Date: Sep 2016
Posts: 274
Default Re: Engine Steady Rods

Thanks again to everyone that chimed in. I’ve talked to Mark and he is sending me some brackets and someone here on the barn offered to give me a set of rods so I’m in great shape!
1stford is offline   Reply With Quote
Old 12-06-2020, 03:44 PM   #16
supereal
Senior Member
 
supereal's Avatar
 
Join Date: Jul 2014
Location: Iowa
Posts: 1,634
Default Re: Engine Steady Rods

The "steady rods" were originally intended to reduce the usual Ford clutch "chatter. They were dropped from production, as they had little effect. Some of the outlets at the time, such as "Western Auto", sold kits for that purpose but, they too, were of little value. The torque tube design, dating from the Model T days, was the culprit.
supereal is offline   Reply With Quote
Old 12-06-2020, 04:17 PM   #17
bobH
Senior Member
 
Join Date: May 2010
Location: so cal, placerville, vegas
Posts: 1,394
Default Re: Engine Steady Rods

I don't think anyone has mentioned rumbleseat here... Paul, in his tech info, I believe addressed all of this with his home-brew fabrication of 'steady-rods'. This info might be of interest to someone?
bobH is offline   Reply With Quote
Old 12-06-2020, 08:32 PM   #18
JSeery
Member Emeritus
 
JSeery's Avatar
 
Join Date: Nov 2012
Location: Wichita KS
Posts: 16,132
Default Re: Engine Steady Rods

Is this the one you're referring to Bob?

ENGINE STAY-RODS: These were used up through the ‘48 engines. They certainly
help control clutch chatter. Run ‘em if you’ve got ‘em.
CLUTCH CHATTER ELIMINATORS: These came out in the forties and were after
market items. They really work on ‘33 thru ‘48 cars with their center X frame.
And are simple to construct and install. The design uses a “V”, a long bolt
threaded on both ends, 4 old pin type shock absorber bushings with washers, two
nuts for the long bolt, and a stout “S” shaped hook. I didn’t include dimensions
since you can determine them for your particular car. The following should help
you with your design. Pictures are currently shown on the Flathead Techno Site.
The front pieces to form the “V” are made from a two lengths of 3/8" X 1" flat
stock. The two pieces have to be long enough to reach from the lower two trans
bolts to about the middle of the trans. You’ll need heat to bend things unless
your fingernails are rough from dragging on the asphalt as you walk! Bend both
ends of each of the two pieces 90 degrees and drill holes in both bends. The two
at the trans should be 3/8" diameter for the trans bolts to go through. Both
rear holes need to be the same diameter as the long rod. Attach the two pieces
to the lower two bolts of the trans without using bushings. Bend the 2 pieces so
the remaining two ends have their 90 degree bends overlap and their holes line
up.
The long rod with both ends threaded back a good inch or so has to be long
enough to go from the intersection of the two pieces you just installed to the
trans and extend to near the front of the X center cross member (6" or so). Put
a bushing and washer on each side of the rod that goes through both pieces from
the trans and hold these together with a nut. The other end of the rod will get
bushings and washers on each side of the “S” shaped hook.
Use a piece of 3/8" flat stock and bend in an elongated “S”. Hook one end in
the rear of the center X frame member. The S goes from the rear of the X member
towards the front of the car. Drill a hole in the other end of the S for the
long rod to go through. Install the rod through the hole in the S hook.
Hook everything up and tighten the nuts quite a bit on each end of the
long rod. This will virtually eliminate nearly all, if not all, clutch
chatter. If you have problem understanding this after going over it while
under your car, please e-mail me and I’ll see if I can help.
JSeery is offline   Reply With Quote
Old 12-06-2020, 09:10 PM   #19
bobH
Senior Member
 
Join Date: May 2010
Location: so cal, placerville, vegas
Posts: 1,394
Default Re: Engine Steady Rods

That sounds like the info. I seem to remember there was a sketch with the info.
But.... don't trust my memory.
bobH is offline   Reply With Quote
Old 12-06-2020, 11:36 PM   #20
JSeery
Member Emeritus
 
JSeery's Avatar
 
Join Date: Nov 2012
Location: Wichita KS
Posts: 16,132
Default Re: Engine Steady Rods

He referenced photo(s) on a site that I believe no longer exist. I think I have a photo of something similar if anyone is interested. I would prefer the add-on mounts and the semi stock steady rod myself.
JSeery is offline   Reply With Quote
Reply

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump

Sponsored Links (Register now to hide all advertisements)


All times are GMT -5. The time now is 07:18 AM.