|
Sponsored Links (Register now to hide all advertisements) |
|
|
Thread Tools | Display Modes |
06-18-2020, 10:26 AM | #1 |
Senior Member
Join Date: Nov 2018
Location: Dahlonega, Ga
Posts: 251
|
Disconnect switch
Does anyone have pictures of a disconnect switch mounted under the front seat?
I can’t figure out a good way to run the cables. Thanks in advance for any responses |
06-18-2020, 11:03 AM | #2 |
Senior Member
Join Date: Jun 2015
Location: Red Deer, Alberta
Posts: 5,042
|
Re: Disconnect switch
Coupe? Sedan? CCPU? Other?
__________________
If you don't hear a rumor by 10 AM, start one!. Got my education out behind the barn! |
Sponsored Links (Register now to hide all advertisements) |
|
06-18-2020, 11:34 AM | #3 |
Senior Member
Join Date: Oct 2019
Location: Virginia
Posts: 140
|
Re: Disconnect switch
This is a picture looking down on the left front corner of the seat mount area on a 29 Town Sedan. The cable runs up through a hole in the floor pan and is installed in the positive ground cable. The handle is just above floor level at the front of the seat mount. I don't have access to take a better picture for a few days.
__________________
1929 Town Sedan (Briggs) 155B, Mitchell Overdrive 1935 Model 48 Tudor |
06-18-2020, 12:52 PM | #4 |
Senior Member
Join Date: May 2019
Location: Fort Worth side of DFW
Posts: 171
|
Re: Disconnect switch
My 1930 coupe has the disconnect mounted up through a hole on the left crossmember and the cables are routed through the hole for the brake rod.
I will add a few pictures later to show the exact locations of the routing. |
06-18-2020, 04:44 PM | #5 |
Senior Member
Join Date: Nov 2018
Location: Dahlonega, Ga
Posts: 251
|
Re: Disconnect switch
Sorry, It’s a 29 Tudor, my bad.
|
06-19-2020, 06:39 AM | #6 |
Senior Member
Join Date: May 2010
Location: VA
Posts: 1,410
|
Re: Disconnect switch
Sponsored Links (Register now to hide all advertisements)
|
06-19-2020, 09:20 AM | #7 |
Senior Member
Join Date: Jul 2011
Location: Redondo Beach, CA
Posts: 5,844
|
Re: Disconnect switch
|
06-20-2020, 02:55 PM | #8 |
Senior Member
Join Date: Nov 2018
Location: Dahlonega, Ga
Posts: 251
|
Re: Disconnect switch
Thanks for the responses, the pics are a great help. But, I’m going to hijack my own thread here though. The instructions that came with my switch say not to turn the disconnect switch off before stopping the engine if it’s an alternator equipped vehicle (mine is), due to “possibly causing alternator diode failure.” I’m also installing a safety fuse at the starter. Question: If the fuse blows while the car is running, wouldn’t that have the same affect as turning the disconnect switch off? I’m making my car 12 Volt negative ground with an alternator.
|
06-28-2020, 01:20 AM | #9 |
Senior Member
Join Date: Dec 2013
Location: Mossel Bay, about 300km from Cape Town
Posts: 530
|
Re: Disconnect switch
Hi Dean,
Some serious points to think about, 1. NEVER EVER admit or suggest that you want to, or have gone to 12v, positive, negative or whatever, NEVER EVER. You will never hear the end of it. I own a 12 volt negative Model A pickup as well as a 29 Chevy and I get it from both forums 2. Seriously now, I believe you are correct, it would be the same as turning off the disconnect which. However, fuses don’t normally blow and I believe, if they do, most probably on start up and only once in a blue moon. Get yourself a little mental checklist, ie, Fuel off, ign off, master off, etc 3. Alternator?(tongue in cheek again) GOTO point nr 1 and never mention it again. In fact, I am seriously considering changing my 250SL Pagoda and my E Type to 6v and generator. Maybe even the 911
__________________
Regards Chris Cape Town 28 Model A RPU, 29 Chevy Phaeton, 67 E Type FHC, 67 250SL Pagoda, 83 911 SC |
06-28-2020, 07:04 AM | #10 |
Senior Member
Join Date: Nov 2018
Location: Dahlonega, Ga
Posts: 251
|
Re: Disconnect switch
Floats: That’s a great response, I love it. Thanks for enlightening me as how criminal it is to convert to a 12 Volt negative ground. I had no idea. I promise never to let it be known again. I won’t let anyone ever look under the hood and if somebody asks about it, I’ll avoid the question or lie if need be.
Last edited by Dean Lemoine; 06-28-2020 at 09:08 AM. |
06-28-2020, 08:31 AM | #11 | |
Senior Member
Join Date: May 2010
Location: Largo Florida
Posts: 7,225
|
Re: Disconnect switch
Quote:
:d:d:d:d:d:d |
|
06-28-2020, 02:02 PM | #12 |
Senior Member
Join Date: Dec 2013
Location: Mossel Bay, about 300km from Cape Town
Posts: 530
|
Re: Disconnect switch
Great Dean, we are on the same page. Don’t let me down.
Cheers Chris
__________________
Regards Chris Cape Town 28 Model A RPU, 29 Chevy Phaeton, 67 E Type FHC, 67 250SL Pagoda, 83 911 SC |
06-28-2020, 06:46 PM | #13 | |
Senior Member
|
Re: Disconnect switch
Quote:
I don’t think anyone can tell you have a 12 volt system by looking under the hood. Even if you’re running an alternator It won’t give your secret away because many people run 6 volt alternators. The only way to tell is by looking at the battery which is safely tucked away under the floor board. David Serrano |
|
Thread Tools | |
Display Modes | |
|
|
Sponsored Links (Register now to hide all advertisements) |
|