Go Back   The Ford Barn > General Discussion > Model A (1928-31)

Sponsored Links (Register now to hide all advertisements)

Reply
 
Thread Tools Display Modes
Old 03-15-2021, 06:42 PM   #1
40-A Twins
Senior Member
 
40-A Twins's Avatar
 
Join Date: Oct 2020
Location: Oregon City, OR
Posts: 121
Default 28-29 lower firewall clearance notch at throttle linkage pivot

Anyone know why the firewall clearance notch is not aligned with the throttle linkage pivot ? if the notch was moved over 3/4" it would be in the right location. Or is this really a 28 firewall with 29 or later throttle linkage pivot ?
Both of my cars have this same misalignment.
Back story on both cars is they have been assembled with parts collected, so manufacture date of some parts is anyone's guess.
Also a photo of each car in original condition when I got them.
Kevin
Attached Images
File Type: jpg firewall notch 1.jpg (78.8 KB, 46 views)
File Type: jpg firewall notch 2.jpg (47.7 KB, 41 views)
File Type: jpg 28 original condition.jpg (75.1 KB, 33 views)
File Type: jpg 29 original condition.jpg (72.7 KB, 32 views)
40-A Twins is offline   Reply With Quote
Old 03-15-2021, 07:19 PM   #2
Steve Plucker
BANNED
 
Join Date: May 2010
Location: Walla Walla, Washington USA
Posts: 6,066
Default Re: 28-29 lower firewall clearance notch at throttle linkage pivot

Try a different throttle linkage.

Pluck
Steve Plucker is offline   Reply With Quote
Sponsored Links (Register now to hide all advertisements)
Old 03-15-2021, 07:27 PM   #3
1955cj5
Senior Member
 
1955cj5's Avatar
 
Join Date: Apr 2015
Location: Boise, Idaho
Posts: 1,576
Default Re: 28-29 lower firewall clearance notch at throttle linkage pivot

I took this when I first brought my 29 ccpu home.

Looks about the same as yours.

Maybe that's the way they were?
Attached Images
File Type: jpg 2015_0814modelajeep0994.jpg (87.4 KB, 22 views)
__________________
Early '29 CCPU that had a 4-speed, but not any more.......in the family since '62
1955cj5 is online now   Reply With Quote
Old 03-15-2021, 08:09 PM   #4
40-A Twins
Senior Member
 
40-A Twins's Avatar
 
Join Date: Oct 2020
Location: Oregon City, OR
Posts: 121
Default Re: 28-29 lower firewall clearance notch at throttle linkage pivot

Luckily I had a 28 linkage in the box-o-parts. Comparing the 28 with later style, it appeared this would not solve the problem because the pivot is in the same relative position to the mounting hole. However, after installing the 28, the solution revealed itself. The 28 foot throttle shaft fits in the center of the notch ! I did not know this until now. This 28 linkage might be the only one I have owned that was not all bent up by somebody trying to pull the motor without unbolting the linkage first.
Kevin
Attached Images
File Type: jpg throttle linkage comparison.jpg (70.7 KB, 20 views)
File Type: jpg 28 linkage installed.jpg (34.2 KB, 22 views)
40-A Twins is offline   Reply With Quote
Old 03-15-2021, 08:19 PM   #5
1955cj5
Senior Member
 
1955cj5's Avatar
 
Join Date: Apr 2015
Location: Boise, Idaho
Posts: 1,576
Default Re: 28-29 lower firewall clearance notch at throttle linkage pivot

Looking in the Judging Standards (1-17) I see what you mean. The earlier assemblies had the foot rod more vertical, instead of having that curve that engaged the hand throttle linkage.

I have no doubt that mine was bent, probably many times.

I know I had trouble getting full throttle travel due to the foot pedal shaft interfering with it's surroundings.

Very interesting!

Maybe the firewall cutout never got modified after the linkage was re-designed.
__________________
Early '29 CCPU that had a 4-speed, but not any more.......in the family since '62

Last edited by 1955cj5; 03-15-2021 at 08:26 PM.
1955cj5 is online now   Reply With Quote
Old 03-15-2021, 08:30 PM   #6
1955cj5
Senior Member
 
1955cj5's Avatar
 
Join Date: Apr 2015
Location: Boise, Idaho
Posts: 1,576
Default Re: 28-29 lower firewall clearance notch at throttle linkage pivot

Sponsored Links (Register now to hide all advertisements)
The Service Bulletins page 337, April 1929, mention the new control assembly design.

No mention is made of the firewall cutout/notch.
__________________
Early '29 CCPU that had a 4-speed, but not any more.......in the family since '62
1955cj5 is online now   Reply With Quote
Old 03-15-2021, 10:55 PM   #7
40-A Twins
Senior Member
 
40-A Twins's Avatar
 
Join Date: Oct 2020
Location: Oregon City, OR
Posts: 121
Default Re: 28-29 lower firewall clearance notch at throttle linkage pivot

A closeup view of the notch in the 29 roadster reveals a worn spot where a 28 style foot throttle shaft makes contact. The gas tank section of the firewall from this body has stamped date of 7-6-28 (I swapped gas tanks with the other car). The rear body cross subrail below the deck lid did not have the 3 nutplates for mounting a 28 cast tail light bracket, which I always assumed was one of the major change between 28 & 29 along with outside door handles. Perhaps I should have researched all of the running changes made before I got this car titled as a 1929.
I may be going out on a limb here, but 1929 pickups would have been using up parts that were obsolete for passenger cars, which would explain the redundant notch.
Kevin
Attached Images
File Type: jpg gas tank stamped date.jpg (21.1 KB, 17 views)
File Type: jpg fierwall notch closeup.jpg (35.7 KB, 20 views)
40-A Twins is offline   Reply With Quote
Reply

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump

Sponsored Links (Register now to hide all advertisements)


All times are GMT -5. The time now is 01:18 PM.