|
Sponsored Links (Register now to hide all advertisements) |
|
|
Thread Tools | Display Modes |
10-24-2021, 04:26 PM | #1 |
Senior Member
Join Date: May 2010
Location: Lynden, Wa
Posts: 3,552
|
front 57 wagon sway bar install
Ok, The front end is done except the sway bar. How the bloody hell does it go in? I put it up into position and it looks like I will have to 'bend' it a bit to get it to conform to the lower arms. Or do I need to rotate it around some more as it should just go straight into position? Any tips/tricks?
Bushings: I have seen bushings by Energy Suspension mentioned and looked at them. It looks like they only do the inner and then I have to stick with the stock outers. Is this correct? Thanks for all of the help as I want her back on the ground. Mike
__________________
1930 TownSedan (Briggs) 1957 Country Sedan |
10-24-2021, 06:23 PM | #2 |
Senior Member
Join Date: Oct 2014
Location: NE Iowa
Posts: 1,664
|
Re: front 57 wagon sway bar install
Not sure if it makes a difference on 57 but are the A arms at ride height or full drop. Is the car up on ramps or jack stands under frame. Energy suspension makes a lot of universal parts, used to be listed in back of catalog. They might not have an exact kit but you may be able to order the parts individually by measurements.
Last edited by 5851a; 10-24-2021 at 06:32 PM. |
Sponsored Links (Register now to hide all advertisements) |
|
10-24-2021, 07:06 PM | #3 |
Senior Member
Join Date: May 2010
Location: Lynden, Wa
Posts: 3,552
|
Re: front 57 wagon sway bar install
She is on stands right now with everything connected. Should she at ride height or stand height?
__________________
1930 TownSedan (Briggs) 1957 Country Sedan |
10-24-2021, 09:05 PM | #4 |
Senior Member
Join Date: Oct 2014
Location: NE Iowa
Posts: 1,664
|
Re: front 57 wagon sway bar install
It may move the connection point outwards a bit if at ride height.
|
10-24-2021, 10:33 PM | #5 |
Senior Member
Join Date: Aug 2012
Location: Abq, NM
Posts: 3,607
|
Re: front 57 wagon sway bar install
If it's on jackstands and the A-arms are hanging in the air at full drop... getting the sway bar hardware to line up can be tough. (as you've discovered)
It should be much easier to install if you can use drive-on ramps under the front of the car, with the suspension at 'normal ride height' or as close as possible. . Last edited by dmsfrr; 10-24-2021 at 11:04 PM. |
10-24-2021, 11:37 PM | #6 |
Senior Member
Join Date: May 2010
Location: Lynden, Wa
Posts: 3,552
|
Re: front 57 wagon sway bar install
Sponsored Links (Register now to hide all advertisements)
Mike
__________________
1930 TownSedan (Briggs) 1957 Country Sedan |
10-25-2021, 12:20 PM | #7 | |
Senior Member
Join Date: Aug 2012
Location: Abq, NM
Posts: 3,607
|
Re: front 57 wagon sway bar install
Quote:
You won't need the swaybar until the car is driveable so put it on later when the car is farther along. |
|
10-25-2021, 03:07 PM | #8 |
Senior Member
Join Date: Jul 2011
Location: Birmingham, AL
Posts: 814
|
Re: front 57 wagon sway bar install
Mike if you want to really improve the handling look at the 58 Edsel Ranger/Pacer bar. It will require mounts added to the frame rails but the holes for the link ends are already in the lower control arms. I believe that set up was used on 58s and 9s, maybe later up to 64.
__________________
Bill, certified Ford nut. 2016 F-150 2016 Focus 08 Shelby GT500 57 Ford Ranchero 36 Chevy, 351C/FMX, 8", Mustang II |
10-25-2021, 06:19 PM | #9 |
Senior Member
Join Date: Aug 2020
Posts: 442
|
Re: front 57 wagon sway bar install
First of all, make sure you're not trying to install it upside down. Initially, wheels should be off the ground; I used stands and floor jack. Turn wheels to lock and maneuver each end into place, turning wheels in/out, as needed, for additional clearance. Once the sway bar has cleared lower control arms and is lined up, bolt the sway bar to the front cross-member/support at original location. Wheels don't have to be on the ground when bolting to cross-member. Attach end links, but do not completely tighten until the wheels are on the ground. If you can beg, borrow/steal ramps,put front wheels on ramps, level car with stands at the rear, and then tighten end links to specs.
I installed a Hotchkis tubular front bar on my 55 Tbird. Clearance around gravel pan/shield, below bumper, was tight, but it all worked out okay. I seem to recall that the Ford service manual actually says to remove the gravel pan; however, the Hotchkis instructions made no mention of it. In my case, it wasn't necessary, even though the Hotchkis bar is considerably thicker than OEM. Be patient, and you'll get 'er done. |
|
|
Sponsored Links (Register now to hide all advertisements) |
|