|
Sponsored Links (Register now to hide all advertisements) |
|
|
Thread Tools | Display Modes |
01-15-2018, 02:21 PM | #1 |
Senior Member
Join Date: May 2010
Location: san diego
Posts: 518
|
Do i need a steering wheel puller for a 41?
hi guys. Do i need a steering wheel puller to remove my 41 coupe wheel for a resto? thanks.
__________________
"I have built my organisation on fear"..Al Capone. |
01-15-2018, 02:54 PM | #2 |
Senior Member
Join Date: May 2010
Location: Coral Springs FL
Posts: 10,933
|
Re: Do i need a steering wheel puller for a 41?
I believe the answer is "Yes". You need one for the 1940 Ford wheel so I assume the same is true of the 41.
See the holes for the wheel puller bolts on this wheel. Some folks beat, pry and pull on the wheel but the wheel may be damaged. https://www.ebay.com/sch/i.html?_fro...el&_sacat=6000 Last edited by 19Fordy; 01-15-2018 at 03:38 PM. |
Sponsored Links (Register now to hide all advertisements) |
|
01-15-2018, 03:47 PM | #3 |
Member
Join Date: Sep 2017
Location: Hamburg Germany
Posts: 36
|
Re: Do i need a steering wheel puller for a 41?
It´s quite hard to find the original tool, so i built a cheap
solution out of crap from my workshop, to remove my 1934 Steering wheel. Just make sure that your downer lifting plate pressures on the steel. Maybe it helps, good luck |
01-15-2018, 03:55 PM | #4 |
Member
Join Date: Aug 2012
Location: HINCKLEY UK
Posts: 51
|
Re: Do i need a steering wheel puller for a 41?
Don’t mess about, if the wheel doesn’t come off with a couple of blows with a rubber mallet. Drill and tap the metal plate ( 1/4 unc) on wheel close to nut. Find an off cut of metal and drill corresponding holes, slacken wheel nut a few turns. Assemble two nuts on bolts. Screw bolts down to bottom out and then thighten nuts down evenly. I removed my model 48 wheel without damage in 20 minutes with this method. The metal plate on the wheel is about 1/4 inch thick, drill slowly and you will feel when you are about to break through, stop immediately or you drill through the wheel hub.
|
01-15-2018, 04:49 PM | #5 |
Senior Member
Join Date: May 2010
Location: Kerrville, Tx
Posts: 2,769
|
Re: Do i need a steering wheel puller for a 41?
1940 wheels are drilled and tapped so I think 41's would be also. I made a strap from1/4" plate that would go in the recess. I don't know if a 41 is recessed. I drilled holes so I could bolt thru with all thread. Tightening the nuts forced the shaft out. Do NOT hit on the shaft. The wheel is not supported and you are jut hitting the bearings in the steering box.
|
01-15-2018, 09:19 PM | #6 |
Senior Member
Join Date: May 2010
Location: Southern California
Posts: 7,031
|
Re: Do i need a steering wheel puller for a 41?
Sponsored Links (Register now to hide all advertisements)
Charlie Stephens |
01-15-2018, 11:33 PM | #7 | |
Junior Member
Join Date: Nov 2017
Location: Calgary
Posts: 6
|
Re: Do i need a steering wheel puller for a 41?
Quote:
Be aware that the two bolt holes in the steering column are 5/16 standard fine thread. I scraped the dirt out with a tiny screwdriver and cleaned the threads with a tap. Bolts went in smooth as silk and it popped it off within a minute. Total elapsed time under 10 minutes |
|
01-16-2018, 08:57 AM | #8 |
Senior Member
Join Date: May 2010
Posts: 1,770
|
Re: Do i need a steering wheel puller for a 41?
if there are no holes in the hub you can make a puller out of a c clamp. on the fixed end weld a u shaped piece of steel that fits over the collum & touches the bottom of the wheel i don,t know how to post picturs but i have made one it did not take long to do & it works great. if you look at the lower photo posted by nico73 you will see what i mean
|
|
|
Sponsored Links (Register now to hide all advertisements) |
|