Go Back   The Ford Barn > General Discussion > Early V8 (1932-53)

Sponsored Links (Register now to hide all advertisements)

Reply
 
Thread Tools Display Modes
Old 02-12-2020, 07:38 PM   #1
Phred
Senior Member
 
Phred's Avatar
 
Join Date: May 2010
Location: IL
Posts: 303
Default Gear Shift Lever

The attached gearshift lever was on a Model B Ford transmission that I am installing in my '28 Phaeton. At first I thought I would like the swoopiness of the lever, but after installation it hits the seat cushion in first and third gear and is a bit tall for my preference. I now would like a straighter and shorter lever.

1) What body style and year(s) is the current lever from?

2) What style/year levers might meet my shorter/straighter desires? I'd rather not try to rework the existing swoopy lever.

Thanks in advance for any input.
Peace, Phred
Attached Images
File Type: jpg Shift Lever1.jpg (44.8 KB, 74 views)
Phred is offline   Reply With Quote
Old 02-12-2020, 08:40 PM   #2
JM 35 Sedan
Senior Member
 
JM 35 Sedan's Avatar
 
Join Date: May 2010
Location: Near Rising Sun, Maryland
Posts: 10,856
Default Re: Gear Shift Lever

That looks like a stock '35 Ford pass car/light commercial Swan neck shift lever to me
__________________
John

"Never give up on what you really want to do. The person with big dreams is more powerful than one with all the facts". Albert Einstein
JM 35 Sedan is offline   Reply With Quote
Sponsored Links (Register now to hide all advertisements)
Old 02-12-2020, 08:45 PM   #3
Lawson Cox
Senior Member
 
Lawson Cox's Avatar
 
Join Date: May 2010
Location: Above the gnat line in Georgia
Posts: 7,009
Default Re: Gear Shift Lever

I agree with John.
__________________
Life is like a roll of toilet paper. The closer to the end, the faster it goes.

It is better to be seen, than viewed.

"We sleep safe in our beds because rough men stand ready in the night to visit violence on those who would do us harm".
Lawson Cox is offline   Reply With Quote
Old 02-12-2020, 08:51 PM   #4
cas3
Senior Member
 
Join Date: Jan 2011
Location: sw minnesota
Posts: 4,543
Default Re: Gear Shift Lever

33-34 lever is what you want
cas3 is offline   Reply With Quote
Old 02-12-2020, 08:51 PM   #5
svm99
Senior Member
 
Join Date: May 2010
Location: Garlic Country of CA
Posts: 537
Default Re: Gear Shift Lever

As others have said, yours is a '35..................you might try a '33/'34 which is straight. Not sure about clearance though.
svm99 is offline   Reply With Quote
Old 02-12-2020, 10:04 PM   #6
Tinker
Senior Member
 
Tinker's Avatar
 
Join Date: May 2010
Location: MN
Posts: 7,053
Default Re: Gear Shift Lever

Sponsored Links (Register now to hide all advertisements)
I'd hate to say that you can cold bend that, it's pretty cool. I'd look at something different, as mentioned, to bend up or cut and weld. It's just metal.


.
Tinker is offline   Reply With Quote
Old 02-12-2020, 10:49 PM   #7
PeteVS
Senior Member
 
PeteVS's Avatar
 
Join Date: May 2010
Location: FP, NJ
Posts: 2,769
Default Re: Gear Shift Lever

There are two designs of the shift lever innards. The older (and I'm not sure of the years but Bruce would have known) was used with the shorter "leaning back" top casting and the newer design was used with the taller "straight up" top casting. The pivot on the shift lever was moved up with the later design resulting in a shorter travel of the shift lever. Might this be a part of your problem?
__________________
Don't never get rid of nuthin!
PeteVS is offline   Reply With Quote
Old 02-12-2020, 10:53 PM   #8
Tinker
Senior Member
 
Tinker's Avatar
 
Join Date: May 2010
Location: MN
Posts: 7,053
Default Re: Gear Shift Lever

I don't think levers were ever cast. Forged. I could be wrong.

Yes Bruce did/does know.
.

Last edited by Tinker; 02-12-2020 at 11:14 PM.
Tinker is offline   Reply With Quote
Old 02-13-2020, 10:20 AM   #9
DavidG
Senior Member
 
DavidG's Avatar
 
Join Date: May 2010
Location: southeastern Michigan
Posts: 10,070
Default Re: Gear Shift Lever

The pre-'36 shift levers won't function in a post-'35 shift lever housing and post-'35 shift lever won't fit in a pre-'36 shift lever housing.
DavidG is offline   Reply With Quote
Old 02-13-2020, 01:44 PM   #10
cas3
Senior Member
 
Join Date: Jan 2011
Location: sw minnesota
Posts: 4,543
Default Re: Gear Shift Lever

i would...determine how far forward you want it by measuring from the dash in 2nd or reverse, then clamp it in the vise , lay a carpenters square on top of the vise and mark with tape at the edge of the vise when the square is at the point where the lever needs to go, then heat the lever at the bottom just above the ball so as not to change the swoop, and bend it until it is at your square. done. i would have a straight one too if you wish
cas3 is offline   Reply With Quote
Old 02-13-2020, 02:24 PM   #11
DavidG
Senior Member
 
DavidG's Avatar
 
Join Date: May 2010
Location: southeastern Michigan
Posts: 10,070
Default Re: Gear Shift Lever

With respect, I believe he indicated that his issue is in 1st and 3rd, not 2nd and reverse.
DavidG is offline   Reply With Quote
Old 02-13-2020, 02:59 PM   #12
cas3
Senior Member
 
Join Date: Jan 2011
Location: sw minnesota
Posts: 4,543
Default Re: Gear Shift Lever

correct, 1&3 hit the seat, so my thought is to measure clearance to the dash so as to get it off the seat. since its in a non stock use, the swoopy lever may not work period, however i would start by measuring clearance with R&2
cas3 is offline   Reply With Quote
Old 02-18-2020, 08:24 AM   #13
Phred
Senior Member
 
Phred's Avatar
 
Join Date: May 2010
Location: IL
Posts: 303
Default Re: Gear Shift Lever

Thanks to all.
I'm going to find a 32 - 34 straight lever as a starting point.

Summary of what I've learned: 32 - 35 shift towers "leaned back, later towers were "upright". 32 - 34 levers were straight, 35 levers were swan shaped. Levers do not interchange between 32-35 towers and later towers.

Peace, Phred
Phred is offline   Reply With Quote
Old 02-18-2020, 09:15 AM   #14
DavidG
Senior Member
 
DavidG's Avatar
 
Join Date: May 2010
Location: southeastern Michigan
Posts: 10,070
Default Re: Gear Shift Lever

Phred,

One further refinement is that only early '32 shift levers are straight (with an elbow near the bottom); most '32 levers have a gentle curve to them before becoming straight as shown in the photo below..
Attached Images
File Type: jpg Book photos 010 (2).jpg (99.9 KB, 27 views)

Last edited by DavidG; 02-18-2020 at 09:53 AM.
DavidG is offline   Reply With Quote
Old 02-19-2020, 06:46 AM   #15
PeteVS
Senior Member
 
PeteVS's Avatar
 
Join Date: May 2010
Location: FP, NJ
Posts: 2,769
Default Re: Gear Shift Lever

I think that later pick ups with floor shift had "straight" shift levers that worked in the later straight up shift towers. Please correct me if I'm wrong.
__________________
Don't never get rid of nuthin!
PeteVS is offline   Reply With Quote
Old 02-19-2020, 12:27 PM   #16
JM 35 Sedan
Senior Member
 
JM 35 Sedan's Avatar
 
Join Date: May 2010
Location: Near Rising Sun, Maryland
Posts: 10,856
Default Re: Gear Shift Lever

Quote:
Originally Posted by PeteVS View Post
I think that later pick ups with floor shift had "straight" shift levers that worked in the later straight up shift towers. Please correct me if I'm wrong.
Yes they did. The levers at top on first and fourth picture are from pu trucks.....
Attached Images
File Type: jpg IMG_20160909_184957701_HDR(1).jpg (36.2 KB, 17 views)
File Type: jpg IMG_20160909_184759898_HDR(1).jpg (38.4 KB, 14 views)
File Type: jpg IMG_20160909_184151808_HDR(1).jpg (34.0 KB, 11 views)
File Type: jpg IMG_20160909_184128388_HDR(1).jpg (36.3 KB, 14 views)
__________________
John

"Never give up on what you really want to do. The person with big dreams is more powerful than one with all the facts". Albert Einstein
JM 35 Sedan is offline   Reply With Quote
Old 02-19-2020, 02:41 PM   #17
PeteVS
Senior Member
 
PeteVS's Avatar
 
Join Date: May 2010
Location: FP, NJ
Posts: 2,769
Default Re: Gear Shift Lever

It appears that the difference between the early and late designs is that the shorter (internals) required a large angular motion to move the first / reverse sliding gear full travel. The longer internals required less angular motion with a shorter throw and the handle.
__________________
Don't never get rid of nuthin!
PeteVS is offline   Reply With Quote
Reply

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump

Sponsored Links (Register now to hide all advertisements)


All times are GMT -5. The time now is 08:44 AM.