Go Back   The Ford Barn > General Discussion > Model A (1928-31)

Sponsored Links (Register now to hide all advertisements)

Reply
 
Thread Tools Display Modes
Old 02-09-2020, 09:17 AM   #21
Bob Bidonde
Senior Member
 
Bob Bidonde's Avatar
 
Join Date: May 2010
Location: Long Island, NY
Posts: 3,429
Default Re: “Do not use a file” to dress down breaker points

Since the 1960s I have been cleaning the oxide coating from ignition points with a point file, emery cloth, rubbing them on cement, a nail clipper file, a finger nail sand board file and scrapping them with a pen knife.
__________________
Bob Bidonde
Bob Bidonde is offline   Reply With Quote
Old 02-10-2020, 01:58 AM   #22
dumb person
Senior Member
 
dumb person's Avatar
 
Join Date: Apr 2011
Location: South pacific island
Posts: 1,724
Default Re: “Do not use a file” to dress down breaker points

Certain people stole my points file.
Where would you recommend i get a new one?
Any favourites you have?
__________________
<Link> This is how we roll<Link>

"I'm Convinced that no one really reads posts anymore; they just fabricate what they think the post says then ramble on about red herrings."--Bob
Outcasts rules of old cars
#1 Fun is imperative, mainstream is overrated
#2 If they think it is impossible, prove them wrong
#3 If the science says it impossible you are not being creative enough.
#4 No shame in recreating something you never had
#5 If it were not for the law & physics you would be unstoppable
dumb person is offline   Reply With Quote
Sponsored Links (Register now to hide all advertisements)
Old 02-10-2020, 11:13 AM   #23
whirnot
Senior Member
 
whirnot's Avatar
 
Join Date: Mar 2013
Location: Bend Or.
Posts: 1,053
Default Re: “Do not use a file” to dress down breaker points

A trick I learned when I had a small engine shop. What ever you use to file the points, or after installing new ones, clean them by drawing a piece of lint free paper through them when closed. A fresh $100 bill works perfectly!
__________________
Bill Worden

1929 Roadster
1929 Briggs Town Sedan
1930 Closed Cab pickup
Smith Motor Compressor
1951 Ford F1

High Desert Model A's
whirnot is offline   Reply With Quote
Old 02-10-2020, 12:35 PM   #24
katy
Senior Member
 
katy's Avatar
 
Join Date: Jun 2015
Location: Red Deer, Alberta
Posts: 5,004
Default Re: “Do not use a file” to dress down breaker points

Quote:
Originally Posted by whirnot View Post
A trick I learned when I had a small engine shop. What ever you use to file the points, or after installing new ones, clean them by drawing a piece of lint free paper through them when closed. A fresh $100 bill works perfectly!
Ditto on cleaning points.

BTW, Any $100 bills I ever had are long gone, and they weren't even fresh.
__________________
If you don't hear a rumor by 10 AM, start one!.
Got my education out behind the barn!
katy is offline   Reply With Quote
Old 02-11-2020, 08:17 AM   #25
old31
Senior Member
 
Join Date: Jan 2016
Posts: 2,087
Default Re: “Do not use a file” to dress down breaker points

Quote:
Originally Posted by whirnot View Post
A trick I learned when I had a small engine shop. What ever you use to file the points, or after installing new ones, clean them by drawing a piece of lint free paper through them when closed. A fresh $100 bill works perfectly!
I only have $1 dollar bills.

It will take me a long time to do the points. I would have to run my $1 bill through the points 100 times.
old31 is offline   Reply With Quote
Old 02-11-2020, 05:35 PM   #26
xray zulu
Junior Member
 
xray zulu's Avatar
 
Join Date: Jun 2019
Location: In The Pines, Michigan
Posts: 11
Default Re: “Do not use a file” to dress down breaker points

Sponsored Links (Register now to hide all advertisements)
I have found that the media used is not the culprit, but the method... IF... You have to dress your points they should be taken off the DIST and honed as a fine blade. I have used a lot of stuff to do this in a pinch, but the common thread was I dressed it with purpose...
xray zulu is offline   Reply With Quote
Old 02-12-2020, 11:29 PM   #27
mass A man
Senior Member
 
mass A man's Avatar
 
Join Date: Jun 2010
Location: Danvers, Ma.
Posts: 711
Default Re: “Do not use a file” to dress down breaker points

I use a little tool called a "Flex-stone" file. It's flat, about 4" long, very fine abrasive, good for cleaning up good but tarnished (or light burnt) points. Won't do much for any really bad pitted points though...I had this back when I did pinball machine repair. Flex stone file used on high voltage contacts. Low voltage blade switches in those machines, I used a strip of a business card, pulled through the closed switch.

Last edited by mass A man; 02-12-2020 at 11:35 PM.
mass A man is offline   Reply With Quote
Old 02-15-2020, 12:59 PM   #28
DHZIEMAN
Senior Member
 
Join Date: Dec 2016
Location: Sunrise Beach, Mo
Posts: 439
Default Re: “Do not use a file” to dress down breaker points

I have always used a point file made for the very purpose! And no problems! And the real solution once wear is a problem, just replace the points!
DHZIEMAN is offline   Reply With Quote
Old 02-15-2020, 08:19 PM   #29
Corley
Senior Member
 
Join Date: Aug 2011
Location: Battle Ground WA
Posts: 293
Default Re: “Do not use a file” to dress down breaker points

You know, they sell "Flex Stones" for this purpose. They cut better than a point file, and are easier to use. About the size of a point file, but made of a flexible plastic material, embedded with abrasive on both sides. They work pretty well.

In my youth, I worked in a small engine shop, and the method used for small engines, chain saws, etc., was folded Emory paper (not Emory cloth), then as a final step, run a matchbook cover through to wipe away any loose grit, then reinstall and adjust gap. Worked every time.

Fine grit wet n' dry sand paper can be used, but the grit tends to delaminate quicker on it.

Anything that knocks the high side off can work, and there's really no need to eliminate all the pits. Spark likes sharp edges.
__________________
Corley
-----------------
Subscribed to the KISS principle!

Last edited by Corley; 02-15-2020 at 08:26 PM.
Corley is offline   Reply With Quote
Reply

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump

Sponsored Links (Register now to hide all advertisements)


All times are GMT -5. The time now is 05:55 AM.