Go Back   The Ford Barn > General Discussion > Late V8 (1954+)

Sponsored Links (Register now to hide all advertisements)

Reply
 
Thread Tools Display Modes
Old 10-11-2016, 08:56 AM   #1
zuburg
Senior Member
 
zuburg's Avatar
 
Join Date: Jun 2015
Location: Raleigh, NC
Posts: 332
Default Replacing brake stop light switch

I replaced the brake stop light switch on my 1956 Thunderbird. This is the part that screws into the brake line block on the frame right under the battery. I assumed I would need to bleed the brakes after, but no brake fluid leaked out when I removed the old one. Do I need to bleed the brakes?
zuburg is offline   Reply With Quote
Old 10-11-2016, 10:42 AM   #2
dmsfrr
Senior Member
 
dmsfrr's Avatar
 
Join Date: Aug 2012
Location: Abq, NM
Posts: 3,598
Default Re: Replacing brake stop light switch

I don't know what the inside of that block looks like and it may be possible there is a small bit of corrosion obstructing the opening and it needs to be cleaned out.
If the switch & brake lights work now it's a good thing.

You may be ok but if it's been a while or the fluid is starting to get dark it won't hurt to bleed/flush the whole system anyway. However, do be careful with the wheel cylinder bleeder valves, they have been known to snap off if they're stuck or rusty.
Normally you'd start with the wheel farthest way from the MC, bleeding until the fluid is clear then repeating with the next farthest and ending with the closest wheel (LF).

Where to start may be different if you have a fender mounted power brake booster. It looks to have a bleeder valve on top. (circled in yellow) It's also the highest point in the system, where air would naturally accumulate.
It might need to be bled first(?) or maybe it takes care of itself when the whole system is bled, I don't know and I hope someone else does 'cuz I'll have to do mine soon and need to know too.
.
Attached Images
File Type: jpg IMG_20160225_223626663c.jpg (84.1 KB, 27 views)

Last edited by dmsfrr; 10-12-2016 at 08:47 PM.
dmsfrr is offline   Reply With Quote
Sponsored Links (Register now to hide all advertisements)
Old 10-11-2016, 04:40 PM   #3
zuburg
Senior Member
 
zuburg's Avatar
 
Join Date: Jun 2015
Location: Raleigh, NC
Posts: 332
Default Re: Replacing brake stop light switch

Yes, as I understand it, you bleed the power booster first, then do right rear, left rear, right front, then left front. I had the new switch and forgot to install it before bleeding the brakes after replacing the hard and soft lines and wheel cylinders. I was hoping to avoid bleeding them again. Maybe I'll bleed them and find no air bubbles, so it won't take too much time and fluid.
zuburg is offline   Reply With Quote
Old 10-11-2016, 07:16 PM   #4
paul2748
Senior Member
 
paul2748's Avatar
 
Join Date: May 2010
Location: Midland Park, NJ
Posts: 3,965
Default Re: Replacing brake stop light switch

You don't have to bleed the brakes if you just replaced the switch. I have replaced a number of these and never had to bleed.

When bleeding the brakes on my 56, I bleed the booster last on the theory that you start at the furthermost point and work forward.

I strongly recommend you install the mechanical switch offered by the TBird parts vendors. Instead of waiting for the correct pressure, the brake lights go on instantly when the pedal is pressed.
__________________
48 Ford Conv
56 Tbird
54 Ford Victoria

Last edited by paul2748; 10-11-2016 at 07:22 PM.
paul2748 is offline   Reply With Quote
Old 10-11-2016, 11:55 PM   #5
Lanny
Senior Member
 
Lanny's Avatar
 
Join Date: May 2010
Location: Mn
Posts: 2,403
Default Re: Replacing brake stop light switch

When bleeding the brakes on my 56, I bleed the booster last on the theory that you start at the furthermost point and work forward.
================================================== ====




Paul, one reason that you would bleed the Master first, is that it produces the pressure,
so you need get all the air bled out of the Master cly, so you can build pressure.
Then start at the furthest wheel cyl, to purge air from the system and work your way to
the front of the vehicle.








.
__________________
My Wife Says That I Never Listen to Her,
I Think That's What She Said


If mama ain't happy, ain't nobody happy.
But if daddy ain't happy...RUN
Lanny is offline   Reply With Quote
Old 10-12-2016, 08:20 PM   #6
paul2748
Senior Member
 
paul2748's Avatar
 
Join Date: May 2010
Location: Midland Park, NJ
Posts: 3,965
Default Re: Replacing brake stop light switch

Sponsored Links (Register now to hide all advertisements)
Lanny- I agree with you, but the question referred to the power brake booster, not the master. Don't know if this makes a difference.
__________________
48 Ford Conv
56 Tbird
54 Ford Victoria
paul2748 is offline   Reply With Quote
Old 10-12-2016, 08:46 PM   #7
Milt K from Pa
Senior Member
 
Milt K from Pa's Avatar
 
Join Date: May 2010
Location: Pittsburgh Pa. Area
Posts: 272
Default Re: Replacing brake stop light switch

Barners,
Earlier this year I replaced the entire brake system including the master. On my T-bird, I flushed the existing steel and flexible lines using fresh silicone fluid, which I was changing to. When the fluid was all purple from all wheels and the power assist, I began the final bleed starting at the power assist on the fender apron. Continued to the farthest rear wheel and etc. It worked out well with no problems.
Good luck.
Milt K from Pa
Milt K from Pa is offline   Reply With Quote
Reply

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump

Sponsored Links (Register now to hide all advertisements)


All times are GMT -5. The time now is 12:36 AM.