Go Back   The Ford Barn > General Discussion > Early V8 (1932-53)

Sponsored Links (Register now to hide all advertisements)

Reply
 
Thread Tools Display Modes
Old 10-01-2020, 07:56 PM   #1
Clem Clement
Senior Member
 
Clem Clement's Avatar
 
Join Date: May 2010
Location: Fairfax, VA
Posts: 3,391
Default Spring clamp torque value?

Torque value for a '40 ford spring clamp, please? I suspect over 100 PSI. Nut is 7/8". 6 out of 8 are loose! None have washers.
Stay strong, Clem
Clem Clement is offline   Reply With Quote
Old 10-01-2020, 08:04 PM   #2
Kube
Senior Member
 
Kube's Avatar
 
Join Date: May 2010
Location: Wisconsin, USA
Posts: 8,937
Default Re: Spring clamp torque value?

Quote:
Originally Posted by Clem Clement View Post
Torque value for a '40 ford spring clamp, please? I suspect over 100 PSI. Nut is 7/8". 6 out of 8 are loose! None have washers.
Stay strong, Clem
Clem,
More often than not, there won't be any washers. The only washers that Ford utilized were hardened flat washers in the rare instance the cotter pin hole in the bolt didn't line up with the slotted nut properly.
If you have the correct U-bolts and bars then simply crank the nuts down as tight as you can and install a cotter pin to each.
There is no specification from Ford for this area that I am aware of.
__________________
"I can explain it for you. However, I can't understand it for you".
Kube is offline   Reply With Quote
Sponsored Links (Register now to hide all advertisements)
Old 10-01-2020, 09:47 PM   #3
Clem Clement
Senior Member
 
Clem Clement's Avatar
 
Join Date: May 2010
Location: Fairfax, VA
Posts: 3,391
Default Re: Spring clamp torque value?

Thanks. You are the goodoest.
The green book shows washers of various part numbers. Interested that the two spring sets with the sheathes on them, have the nuts loose. I thought maybe some of the sheathes were compressing/adjusting. I'll fix things.
Clem Clement is offline   Reply With Quote
Old 10-02-2020, 08:22 AM   #4
Kube
Senior Member
 
Kube's Avatar
 
Join Date: May 2010
Location: Wisconsin, USA
Posts: 8,937
Default Re: Spring clamp torque value?

Quote:
Originally Posted by Clem Clement View Post
Thanks. You are the goodoest.
The green book shows washers of various part numbers. Interested that the two spring sets with the sheathes on them, have the nuts loose. I thought maybe some of the sheathes were compressing/adjusting. I'll fix things.
Sheathes? Do you mean the tin covers? If so, the covers should NOT be beneath the clamps.
__________________
"I can explain it for you. However, I can't understand it for you".
Kube is offline   Reply With Quote
Old 10-02-2020, 12:23 PM   #5
19Fordy
Senior Member
 
19Fordy's Avatar
 
Join Date: May 2010
Location: Coral Springs FL
Posts: 10,875
Default Re: Spring clamp torque value?

Here's some U-bolt torque specs. that may be helpful as a guide.
https://www.suspensionspecialists.co...nformation.pdf

Of course you tighten the bolts with the car resting on the ground, not on jack stands.
19Fordy is offline   Reply With Quote
Old 10-02-2020, 02:10 PM   #6
Clem Clement
Senior Member
 
Clem Clement's Avatar
 
Join Date: May 2010
Location: Fairfax, VA
Posts: 3,391
Default Re: Spring clamp torque value?

Sponsored Links (Register now to hide all advertisements)
car resting on the ground. thread and cross pieces lubed with 30 weight oil. 39 pickup started with 10-20 Psi torque. Worked them all up the 50psi. Nuts are 7/8th. There was some crunching of dirt and rust as the spring leaves moved.
I'll retighten up to 76 after I gain strength form my nap
Clem Clement is offline   Reply With Quote
Old 10-02-2020, 04:04 PM   #7
Kube
Senior Member
 
Kube's Avatar
 
Join Date: May 2010
Location: Wisconsin, USA
Posts: 8,937
Default Re: Spring clamp torque value?

Quote:
Originally Posted by 19Fordy View Post
Here's some U-bolt torque specs. that may be helpful as a guide.
https://www.suspensionspecialists.co...nformation.pdf

Of course you tighten the bolts with the car resting on the ground, not on jack stands.
Interesting. Thank you
__________________
"I can explain it for you. However, I can't understand it for you".
Kube is offline   Reply With Quote
Old 10-02-2020, 04:15 PM   #8
19Fordy
Senior Member
 
19Fordy's Avatar
 
Join Date: May 2010
Location: Coral Springs FL
Posts: 10,875
Default Re: Spring clamp torque value?

Just a note: Don't be tempted to over do it and tighten with a long pipe on your ratchet handle as it's easy to strip the threads.
19Fordy is offline   Reply With Quote
Old 10-03-2020, 02:11 PM   #9
Clem Clement
Senior Member
 
Clem Clement's Avatar
 
Join Date: May 2010
Location: Fairfax, VA
Posts: 3,391
Default Re: Spring clamp torque value?

19Fordy:
Thanks. I don't have many psi in these old skinny arms. I set both vehicles at 51 psi. All 8 bolts were loose. The tin sleeves over the springs did not extend to t6he spring clamp area.
Clem Clement is offline   Reply With Quote
Old 10-03-2020, 02:15 PM   #10
19Fordy
Senior Member
 
19Fordy's Avatar
 
Join Date: May 2010
Location: Coral Springs FL
Posts: 10,875
Default Re: Spring clamp torque value?

Clem, That seems a little light on the torque. Wheel lug nuts are tighter than that.
However, I am no expert. If the nuts were tight and you turned them just a hair more to insert a cotter pin, then you are probably ok.
19Fordy is offline   Reply With Quote
Old 10-03-2020, 08:57 PM   #11
Clem Clement
Senior Member
 
Clem Clement's Avatar
 
Join Date: May 2010
Location: Fairfax, VA
Posts: 3,391
Default Re: Spring clamp torque value?

19Fordy,
Thanks. I used the twist bar/long pointer for the torque measurements. It seems that as I got near 50 psi, attaining the 50 moved away. I have a modern torque wrench, but it sets at 25 right now and I was too lazy to spend the time to crank it up to 75.

I suffered a little yesterday pulling on the wrench. Thanks for your opinion. I saw a number somewhere that a 7/8th nut design limit is 120 psi.

I just realized that I chose cotter pins new from my general pin jar. The Merc is a national car: I assume the cotter pins are checked for proper size?? If I have to change them, I want to get the torque correct.

The frame has a thick coat of white stuff under the black. Perhaps this is crumbling under the torque load??

Thanks all for your assistance
Clem
Clem Clement is offline   Reply With Quote
Old 10-03-2020, 09:58 PM   #12
19Fordy
Senior Member
 
19Fordy's Avatar
 
Join Date: May 2010
Location: Coral Springs FL
Posts: 10,875
Default Re: Spring clamp torque value?

Good job Clem. Sounds like you are "good to go".
19Fordy is offline   Reply With Quote
Old 10-03-2020, 10:31 PM   #13
koates
Senior Member
 
Join Date: May 2010
Location: Melbourne Australia.
Posts: 2,076
Default Re: Spring clamp torque value?

Clem, just to clarify when torquing nuts or bolts you go by the thread size and type and not by the physical size of the nut or bolt head. Regards, Kevin.
koates is offline   Reply With Quote
Old 10-04-2020, 12:16 AM   #14
Clem Clement
Senior Member
 
Clem Clement's Avatar
 
Join Date: May 2010
Location: Fairfax, VA
Posts: 3,391
Default Re: Spring clamp torque value?

Thanks. I thought I read it some place. I'll see it I can find the source again.

Do you think 50 is good enough for the spring clip nuts? I started think task with several of the nuts hand tight and one cross piece moveable.
TIA,
Clem
Clem Clement is offline   Reply With Quote
Old 10-04-2020, 06:18 AM   #15
koates
Senior Member
 
Join Date: May 2010
Location: Melbourne Australia.
Posts: 2,076
Default Re: Spring clamp torque value?

Clem, I dont think you have to worry about a torque wrench on those spring clamp nuts. Just do them up fairly tight and leave it there. The split pins will prevent an tendency to come loose. By the way measurements are in ft/lbs of torque and not PSI as you suggested. (I know, just a slip of the finger). Regards, Kevin.
koates is offline   Reply With Quote
Old 10-04-2020, 05:49 PM   #16
Clem Clement
Senior Member
 
Clem Clement's Avatar
 
Join Date: May 2010
Location: Fairfax, VA
Posts: 3,391
Default Re: Spring clamp torque value?

thanks. I started with hand tight nuts on both cars. 50 is much better.
Clem Clement is offline   Reply With Quote
Old 10-07-2020, 09:26 AM   #17
itslow
Senior Member
 
itslow's Avatar
 
Join Date: May 2010
Location: Central Iowa
Posts: 687
Default Re: Spring clamp torque value?

Quote:
Originally Posted by Clem Clement View Post
car resting on the ground. thread and cross pieces lubed with 30 weight oil. 39 pickup started with 10-20 Psi torque. Worked them all up the 50psi. Nuts are 7/8th. There was some crunching of dirt and rust as the spring leaves moved.
I'll retighten up to 76 after I gain strength form my nap
Fasteners should be tightened without any sort of lubricant unless specified. It will reduce the amount of torque required to reach X amount of bolt stretch, often in an unreliable manner.

These numbers are just wild examples, but a torque of 50 ft-lbs (lubricated) would be like 75 ft-lbs (unlubricated). It makes it very easy to over-stretch the fastener.

I doubt Ford specifies use of any lubricant on such spring fasteners.
__________________
Mike

Wanted:
- '32-34 Open Cab Pickup (RPU) parts and documents/articles/info
- ARDUN parts
itslow is offline   Reply With Quote
Old 10-07-2020, 10:34 AM   #18
Lawson Cox
Senior Member
 
Lawson Cox's Avatar
 
Join Date: May 2010
Location: Above the gnat line in Georgia
Posts: 7,009
Default Re: Spring clamp torque value?

You young fellers need to understand something. Old Ford mechanics or shade tree mechanics didn't use torque wrenches. We just tightened the nuts up till they felt right and went with it. Don't overthink a situation. My 2¢. Keep on V8ing.
__________________
Life is like a roll of toilet paper. The closer to the end, the faster it goes.

It is better to be seen, than viewed.

"We sleep safe in our beds because rough men stand ready in the night to visit violence on those who would do us harm".
Lawson Cox is offline   Reply With Quote
Old 10-10-2020, 05:46 PM   #19
Clem Clement
Senior Member
 
Clem Clement's Avatar
 
Join Date: May 2010
Location: Fairfax, VA
Posts: 3,391
Default Re: Spring clamp torque value?

Love ya "Lawson!!! "
TLAR" -That Looks About Right
Clem Clement is offline   Reply With Quote
Old 10-10-2020, 06:16 PM   #20
Kube
Senior Member
 
Kube's Avatar
 
Join Date: May 2010
Location: Wisconsin, USA
Posts: 8,937
Default Re: Spring clamp torque value?

Quote:
Originally Posted by Lawson Cox View Post
You young fellers need to understand something. Old Ford mechanics or shade tree mechanics didn't use torque wrenches. We just tightened the nuts up till they felt right and went with it. Don't overthink a situation. My 2¢. Keep on V8ing.
Lawson, I agree with you in part.
There is "good enough" and many times, that's just what it is - "good enough".
Then there is "done correctly" which will always be just that - done correctly.
Given the choice, I'd go with "always".
__________________
"I can explain it for you. However, I can't understand it for you".
Kube is offline   Reply With Quote
Reply

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump

Sponsored Links (Register now to hide all advertisements)


All times are GMT -5. The time now is 07:42 PM.