Go Back   The Ford Barn > General Discussion > Early V8 (1932-53)

Sponsored Links (Register now to hide all advertisements)

Reply
 
Thread Tools Display Modes
Old 10-21-2020, 11:31 AM   #1
tomkc1
Senior Member
 
tomkc1's Avatar
 
Join Date: Dec 2011
Location: York, ME/Astor, FL
Posts: 139
Default My '34 Won't Turnover

I'm back to Florida and my '34 has been sitting in the garage since mid June. I've never had an issue with the engine not turning over until the other day when I tried to start the car for the first time.
I take the battery out during the summer. I charged it and put it back in the car. Checking it with a tester it has plenty of juice.
I turned the ignition switch on and the ammeter drops slightly, just under "0". When I press on the starter button the engine does not turnover. It doesn't click or anything. Looking at the ammeter when I press on the starter button it goes back to "0".
I checked the wire on the starter. Its clean and tight.
I'm thinking that the problem is something simple since I've never had an issue with it starting. Also, the starter was rebuilt a couple of years ago.
Anyone got any suggestions?
Thanks, Tom
tomkc1 is offline   Reply With Quote
Old 10-21-2020, 11:41 AM   #2
Kurt in NJ
Senior Member
 
Kurt in NJ's Avatar
 
Join Date: May 2010
Location: on the Littlefield
Posts: 6,140
Default Re: My '34 Won't Turnover

Turn on headlights--- observe brightness, engauge starter--- does brightness change?
Kurt in NJ is offline   Reply With Quote
Sponsored Links (Register now to hide all advertisements)
Old 10-21-2020, 12:01 PM   #3
rockfla
Senior Member
 
rockfla's Avatar
 
Join Date: Mar 2014
Location: Jacksonville FL
Posts: 3,926
Default Re: My '34 Won't Turnover

What did you check your battery with??? If a VO meter that's not necessarily and indicator of a "good" battery. You need to check them with a hydrometer and check each cell!!! you could have a bad cell or two, it will still give you 6V but not near enough AMPS. The headlight test will also "help" tell, they won't stay lit long at all with a two bad cells!!!

Last edited by rockfla; 10-21-2020 at 12:22 PM.
rockfla is online now   Reply With Quote
Old 10-21-2020, 12:45 PM   #4
tomkc1
Senior Member
 
tomkc1's Avatar
 
Join Date: Dec 2011
Location: York, ME/Astor, FL
Posts: 139
Default Re: My '34 Won't Turnover

4 balls floating in each cell with the tester. Battery is reading over 7 volts.
tomkc1 is offline   Reply With Quote
Old 10-21-2020, 12:50 PM   #5
petehoovie
Senior Member
 
petehoovie's Avatar
 
Join Date: May 2015
Posts: 7,924
Default Re: My '34 Won't Turnover

Maybe the starter pinion gear is hung-up on the flywheel. Rock the car back and forth in high gear. It will make a 'clunk' sound when it releases....
__________________
The only thing nice about being imperfect is the joy it brings to others....

"Silver rings, your butt! Them's washers!"
"We shot our way out of that town for a dollar's worth of steel holes!" - from 'The Wild Bunch' - 1969

https://www.youtube.com/watch?v=7NReUd2_0u0

Last edited by petehoovie; 10-22-2020 at 12:36 AM.
petehoovie is offline   Reply With Quote
Old 10-21-2020, 12:55 PM   #6
drolston
Senior Member
 
drolston's Avatar
 
Join Date: Jun 2014
Location: Williamsburg, VA
Posts: 1,622
Default Re: My '34 Won't Turnover

Sponsored Links (Register now to hide all advertisements)
Clean the battery terminal connections, all connections to ground, from ground to engine, and to the starter. If that does not fix it, suspect the starter switch. I presume you have the one on the floor. If that has been replaced by a solenoid, suspect the solenoid.
drolston is offline   Reply With Quote
Old 10-21-2020, 01:51 PM   #7
rockfla
Senior Member
 
rockfla's Avatar
 
Join Date: Mar 2014
Location: Jacksonville FL
Posts: 3,926
Default Re: My '34 Won't Turnover

Then "Petehoovie" first, then follow Drolston's advice!!!
rockfla is online now   Reply With Quote
Old 10-21-2020, 01:54 PM   #8
51woodie
Senior Member
 
51woodie's Avatar
 
Join Date: Apr 2018
Location: Chelmsford, ON Canada
Posts: 524
Default Re: My '34 Won't Turnover

When you say it doesn’t click or anything, I would suspect the starter solenoid. Jump from the battery direct to the starter to see if that works.
51woodie is offline   Reply With Quote
Old 10-21-2020, 01:57 PM   #9
KiWinUS
Senior Member
 
KiWinUS's Avatar
 
Join Date: May 2010
Location: Charlotte NC KiWi-L100 available here
Posts: 2,945
Default Re: My '34 Won't Turnover

Load test battery
KiWinUS is offline   Reply With Quote
Old 10-21-2020, 02:14 PM   #10
Lawson Cox
Senior Member
 
Lawson Cox's Avatar
 
Join Date: May 2010
Location: Above the gnat line in Georgia
Posts: 7,009
Default Re: My '34 Won't Turnover

Quote:
Originally Posted by 51woodie View Post
When you say it doesn’t click or anything, I would suspect the starter solenoid. Jump from the battery direct to the starter to see if that works.
A 34, if stock, does not have a solenoid.
__________________
Life is like a roll of toilet paper. The closer to the end, the faster it goes.

It is better to be seen, than viewed.

"We sleep safe in our beds because rough men stand ready in the night to visit violence on those who would do us harm".
Lawson Cox is offline   Reply With Quote
Old 10-21-2020, 04:33 PM   #11
Ggmac
Senior Member
 
Join Date: Jul 2016
Location: Lake worth Florida
Posts: 1,073
Default Re: My '34 Won't Turnover

Clean all ground straps . Corrosion is a big problem down here . Check starter to block , frame to engine and body , all need good clean ground.
Ggmac is offline   Reply With Quote
Old 10-21-2020, 04:33 PM   #12
cadillac512
Senior Member
 
cadillac512's Avatar
 
Join Date: Apr 2019
Location: Kansas
Posts: 897
Default Re: My '34 Won't Turnover

Quote: "I turned the ignition switch on and the ammeter drops slightly, just under "0". When I press on the starter button the engine does not turnover. It doesn't click or anything. Looking at the ammeter when I press on the starter button it goes back to "0"."


That returning of the gauge to 0 when you press the starter button sounds like a battery connection OR a battery that goes open circuit when load is applied. To test, press the starter button while your volt meter is on the battery. If it drops to near 0 the battery is done. If it stays at a good voltage level, it's probably a connection.


Terry
__________________
"It don't take but country smarts to solve the problem" (Smokey Yunick)


'41 Merc Town Sedan / 260" 8CM engine
'66 Fairlane four door / "warmed up" 302
cadillac512 is offline   Reply With Quote
Old 10-21-2020, 06:12 PM   #13
51woodie
Senior Member
 
51woodie's Avatar
 
Join Date: Apr 2018
Location: Chelmsford, ON Canada
Posts: 524
Default Re: My '34 Won't Turnover

My post on the solenoid was obviously wrong, and I learn something new every day on this site. When did Ford start using solenoids in the starting circuit?
51woodie is offline   Reply With Quote
Old 10-21-2020, 06:16 PM   #14
JSeery
Member Emeritus
 
JSeery's Avatar
 
Join Date: Nov 2012
Location: Wichita KS
Posts: 16,132
Default Re: My '34 Won't Turnover

Quote:
Originally Posted by 51woodie View Post
When did Ford start using solenoids in the starting circuit?
Around 37, 36 still had a floor starter switch and 37 had a firewall starter solenoid, but not sure if it was a model year change or not.
JSeery is offline   Reply With Quote
Old 10-21-2020, 08:35 PM   #15
BLACKNRED
Senior Member
 
BLACKNRED's Avatar
 
Join Date: Jun 2010
Location: adelaide australia
Posts: 163
Default Re: My '34 Won't Turnover

If you are using the original foot starter switch, that may be an issue.
Mine shit itself, really poor contact and it was hit or miss that the starter would engage to the point I thought the starter was shot, replaced it, what a difference just like new.
BLACKNRED is offline   Reply With Quote
Old 10-22-2020, 02:01 AM   #16
koates
Senior Member
 
Join Date: May 2010
Location: Melbourne Australia.
Posts: 2,076
Default Re: My '34 Won't Turnover

The ammeter has NOTHING to do do with the starter motor or cranking circuit so dont look at it. Have someone push the starter switch on the floor while you give the starter motor a bit of a tap-tap with a hammer and see if it cranks. If it does not crank then you will have to do some TESTING with a voltmeter or a test light and find out where you have or have not got power. The only way to test a batteries capacity to do work is with a load tester which loads a battery with about 200 amps or so for a short time, about 10 or 15 seconds. Most home workshops dont have a good one of those so take it to an auto electrical shop and have them test it. Im not convinced a local parts shop have a proper load tester. The old foot starter switches get a bit tired and new ones are around on ebay. As I said you need to test and not just guess by replacing parts. Regards, Kevin.
koates is offline   Reply With Quote
Old 10-22-2020, 08:19 AM   #17
Pat/Ohio
Senior Member
 
Pat/Ohio's Avatar
 
Join Date: May 2010
Location: Wilmington, OH/Lakeland, FL
Posts: 950
Default Re: My '34 Won't Turnover

I had a similar issue with my '32 V8 5W. After checking all the connections and not finding any issues, I checked for continuity at the battery terminal clamp and the battery cable to that clamp and found none. I removed the terminal clamp on that battery cable and cleaned good and re-installed it. Started right up! If you have factory installed clamps...probably not the problem. I had shortened my battery cable at one time and installed the clamp myself. Good luck!

Pat
Pat/Ohio is online now   Reply With Quote
Old 10-22-2020, 08:29 AM   #18
joe 1950
Senior Member
 
joe 1950's Avatar
 
Join Date: Mar 2013
Location: Green Bay Wi
Posts: 400
Default Re: My '34 Won't Turnover

Be careful when doing some of these tests make sure you have the ignition off when tapping the starter and also the gear shift in neutral to many times these old girls will start when you didn’t expect it to and remember it doesn’t take much current to light a light bulb but takes a lot to turn the starter
joe 1950 is offline   Reply With Quote
Old 10-22-2020, 10:29 AM   #19
51woodie
Senior Member
 
51woodie's Avatar
 
Join Date: Apr 2018
Location: Chelmsford, ON Canada
Posts: 524
Default Re: My '34 Won't Turnover

There is a YouTube on the A site that goes over the rebuild of the starter button.

https://www.youtube.com/watch?v=lDBNoU0ZvLQ&app=desktop
51woodie is offline   Reply With Quote
Old 10-22-2020, 10:58 AM   #20
big job
Senior Member
 
big job's Avatar
 
Join Date: Sep 2013
Location: Dighton, Mass
Posts: 1,225
Default Re: My '34 Won't Turnover

Lets see turn ign on amp shows a little discharge thats good that means coil juice. step on the starter amp gauge shows 0 and nothing happens. And mentioned to turn on headlights then step on the starter do the lights go out: yes or no. If yes you had better check cables with a test light. If no its the starter switch known bad out of the box. If you
took that switch apart I bet the disk and contacts are all black and its getting a little
sizzle contact to kill the coil but not enough power for the starter &
(amp meter goes to 0) thats a red flag. We built a test stand for V8s have that starter
switch all common to tractors industrial engines. the first push Junk. So I say take the
starter cable off and with test light on that cable now press the switch does test light
glow ? if yes now ground that cable and I bet the light will go out. starter switch juck.
big job is offline   Reply With Quote
Reply

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump

Sponsored Links (Register now to hide all advertisements)


All times are GMT -5. The time now is 08:29 AM.