|
Sponsored Links (Register now to hide all advertisements) |
|
|
Thread Tools | Display Modes |
07-13-2021, 02:14 PM | #1 |
Senior Member
Join Date: May 2010
Location: Lynden, Wa
Posts: 3,551
|
best way to get heads off
Hi all,
What is the best way/tool to get a set of heads off? The bolts all came out nice and easily, most were all coated with oil but two center bolts came out with what appears to be water droplets on them. I looked in the manual and I don't have the special tool that they show. Do I need a special head puller? Thanks, Mike
__________________
1930 TownSedan (Briggs) 1957 Country Sedan |
07-13-2021, 02:38 PM | #2 |
Senior Member
Join Date: Mar 2018
Location: Arkansas
Posts: 525
|
Re: best way to get heads off
Been too long since I worked on a Y block but there is usually a spot you can stick a screwdriver and should just pop off.
|
Sponsored Links (Register now to hide all advertisements) |
|
07-13-2021, 05:54 PM | #3 |
Senior Member
Join Date: Dec 2010
Location: p.e.i.
Posts: 1,060
|
Re: best way to get heads off
if they havent used sealer on the gaskets they come of easy.
|
07-13-2021, 06:05 PM | #4 |
Member
Join Date: Jul 2010
Posts: 63
|
Re: best way to get heads off
|
07-13-2021, 06:40 PM | #5 |
Senior Member
Join Date: May 2010
Location: Lynden, Wa
Posts: 3,551
|
Re: best way to get heads off
The heads have never been off the engine, so they are just plain hard to remove I think. Dominic, thanks for the pic I will give that spot a try tomorrow.
Mike
__________________
1930 TownSedan (Briggs) 1957 Country Sedan |
07-13-2021, 06:51 PM | #6 |
Member
Join Date: Oct 2020
Posts: 73
|
Re: best way to get heads off
Sponsored Links (Register now to hide all advertisements)
|
07-13-2021, 07:38 PM | #7 |
Senior Member
Join Date: May 2010
Location: Lynden, Wa
Posts: 3,551
|
Re: best way to get heads off
Yeah, I was thinking the intake ports as well-gently of course.
Mike
__________________
1930 TownSedan (Briggs) 1957 Country Sedan |
07-13-2021, 09:27 PM | #8 |
Senior Member
Join Date: Aug 2012
Location: IN A 'GALAXIE' FAR FAR AWAY
Posts: 6,475
|
Re: best way to get heads off
There you go, no possible damage to the mating surfaces. Just steer clear of valves.
__________________
***** - WHY IS IT ... - ... that everything you buy in the grocery store is either wrapped in or contained in plastic but the government doesn't want you to carry it out in a plastic bag? WONDERING IN W(BY GOD)V ...
DIAGNOSED CDO - (OCD In Correct Alphabetical Order) |
07-13-2021, 10:18 PM | #9 |
Senior Member
Join Date: May 2010
Location: Granite City, Illinois
Posts: 3,008
|
Re: best way to get heads off
If you're talking about a Y-block, notice that there is a little portion at the bottom of the head that protrudes from the engine block at the front.
I have always taken a large, regular screwdriver and stuck it under that little lip there, then tapped the bottom of the screwdriver with a hammer. That will cause it to pop up a little bit. Another way to do it is to have two 1/2" diameter steel rods, each about a foot long. One end of each rod should be beveled round at one end. Stick the beveled end of one rod in the second or third exhaust port and stick the beveled end of the other rod at the opposite end intake port. (Back that one out as needed to keep away from valve stem). Grab the two rods and pull up and the head should break free (after all the bolts are out, of course). I've done it both ways. Always worked for me. |
07-14-2021, 03:02 PM | #10 |
Senior Member
Join Date: May 2010
Location: Lynden, Wa
Posts: 3,551
|
Re: best way to get heads off
Well they are off! Used a block of wood and some tire irons and they popped right off easily, after a few good whacks. And this is what I found.
GOOD-Some carbon ridge-albeit not all of the way around and just a very slight wear ridge. No major scoring, although there is one spot that can be seen and just barely felt. Standard bore, clean piston tops-more or less and Ford valves in the heads. Not bad for a sub 50K engine. BAD-some sludge, not much and it will get cleaned out when on the stand. some scale and goop in the antifreeze in the water jackets. Rust on some valve heads but I think that is from sitting in the yard. Overall, she is in pretty good shape. Next up is to see what the bearing look like. What do you all think? Passenger head/block and then driver side head/block and finally #6 before scraping and after. Mike
__________________
1930 TownSedan (Briggs) 1957 Country Sedan |
07-14-2021, 05:06 PM | #11 |
Senior Member
Join Date: Jun 2010
Location: Detroit suburb, MI
Posts: 3,705
|
Re: best way to get heads off
Those appear to be 471 heads, which were used on '59 292's. They have the big valves like the '57 ECZ-G heads but larger combustion chamber, so about one number lower on the compression ratio.
I think you said the engine came out of a '57, so at least the heads aren't original. All passenger car Y-Blocks in '57 had ECZ-G heads. Sal |
07-14-2021, 06:27 PM | #12 |
Senior Member
Join Date: May 2010
Location: Lynden, Wa
Posts: 3,551
|
Re: best way to get heads off
Yep, I just found them on the Y block guy site. So now I don't know what to make of the motor. I will check the bearings this weekend. I may just use these heads as is for now and look for the correct heads later.
Mike
__________________
1930 TownSedan (Briggs) 1957 Country Sedan |
07-14-2021, 08:12 PM | #13 |
Member
Join Date: Jul 2010
Posts: 63
|
Re: best way to get heads off
The extra steam holes drilled in the block between the center cylinders could have been added later, but my bet would be the block is the same vintage as the heads.
|
07-15-2021, 04:32 AM | #14 |
Senior Member
Join Date: Dec 2010
Location: p.e.i.
Posts: 1,060
|
Re: best way to get heads off
what are the casting letters on the block.59 blocks are b9ae.they didnt have the steam holes until the the last 2 years 63 and 4.unless you have one of these its a rebuilt.
|
07-15-2021, 08:53 AM | #15 |
Senior Member
Join Date: Jul 2010
Location: Conifer, Colorado
Posts: 2,429
|
Re: best way to get heads off
|
07-15-2021, 10:16 AM | #16 | |
Senior Member
Join Date: Jun 2010
Location: Detroit suburb, MI
Posts: 3,705
|
Re: best way to get heads off
Quote:
Sal |
|
07-15-2021, 01:22 PM | #17 |
Senior Member
Join Date: Aug 2012
Location: IN A 'GALAXIE' FAR FAR AWAY
Posts: 6,475
|
Re: best way to get heads off
Oh, she's very careful not to leave any marks. She can take a cast iron frying pan and bounce it off the side of my head (sounding similar to church bells) with no resultant lacerations or swelling.
__________________
***** - WHY IS IT ... - ... that everything you buy in the grocery store is either wrapped in or contained in plastic but the government doesn't want you to carry it out in a plastic bag? WONDERING IN W(BY GOD)V ...
DIAGNOSED CDO - (OCD In Correct Alphabetical Order) |
07-15-2021, 01:26 PM | #18 |
Senior Member
Join Date: May 2010
Location: Lynden, Wa
Posts: 3,551
|
Re: best way to get heads off
So, since this engine has been opened-at least on the top end so far-it has become a Frankenstein motor. Not that that is bad, but just not what I was hoping for. I checked the numbers on the block, heads, exh and intake manifolds and I get different years. This is what I got:
Block= ECZ 6015C=292/312 Exhaust manifolds R=B9AE, L=EDB (58-59 292 manifolds) Water outlet=ECE-8/3 Intake=ECZ-9425-B So my guess is this, the engine is a genuine low mileage 312 (well at least at this point in time) that went to the fairlane I got it out of. But at some point the heads and manifolds got replaced along with the valley pan. The only reason I say this about the pan is that it was designed with a PCV valve in it from the factory. It has a stamped indentation where the valve sits so I don't think it is a later mod. Mike K, the 4100 on this car came with an electric choke? Why? I thought they all were mechanical pulling heat from the manifold. That is preferable as there are fewer possible problems.
__________________
1930 TownSedan (Briggs) 1957 Country Sedan |
07-15-2021, 02:00 PM | #19 |
Senior Member
Join Date: May 2012
Location: Middle TN
Posts: 1,060
|
Re: best way to get heads off
It's a Ford/Autolite 4100. They came out in 1957. To my knowledge they were all electric choke. These are great carbs, prolly about as close to set it and forget it as it gets. The venturis are annular discharge, good for gas mileage and performance. If you don't want it I would be happy to get it out of your way...
__________________
Often wrong but never in doubt. |
07-15-2021, 02:29 PM | #20 | ||
Senior Member
Join Date: Aug 2012
Location: IN A 'GALAXIE' FAR FAR AWAY
Posts: 6,475
|
Re: best way to get heads off
Quote:
In all actuality, an electric choke is a better performer. Much less maintenance and mechanical problems. Quote:
AUTOLITE and MOTORCRAFT were marketing terms. All had hot air chokes
__________________
***** - WHY IS IT ... - ... that everything you buy in the grocery store is either wrapped in or contained in plastic but the government doesn't want you to carry it out in a plastic bag? WONDERING IN W(BY GOD)V ...
DIAGNOSED CDO - (OCD In Correct Alphabetical Order) |
||
|
|
Sponsored Links (Register now to hide all advertisements) |
|