|
Sponsored Links (Register now to hide all advertisements) |
|
![]() |
![]() |
Thread Tools | Display Modes |
|
![]() |
#1 |
Senior Member
Join Date: Apr 2012
Posts: 1,542
|
![]()
I know the factory advice was to squirt graphite into the key hole, but has anyone know if that electronic contact cleaner spray is safe to try?
|
![]() |
![]() |
![]() |
#2 |
Senior Member
Join Date: May 2010
Location: Portland, Oregon
Posts: 5,906
|
![]()
Electrolock bodies are pot metal. Moisture can cause them to get deformed, and make the lock piston sticky. Eventually the lock body can crack or break. I can’t say for sure that is your problem, but that is what happened to my original popout. I tried the graphite first, but it didn’t work. You might have better luck. Always best to try the easy stuff first.
__________________
Ray Horton, Portland, OR As you go through life, keep your eye on the donut, not the hole. ![]() |
![]() |
![]() |
Sponsored Links (Register now to hide all advertisements) |
|
![]() |
#3 |
Senior Member
Join Date: Sep 2019
Location: Fort Gratiot, Michigan
Posts: 2,296
|
![]() |
![]() |
![]() |
![]() |
#4 |
Senior Member
Join Date: Apr 2012
Posts: 1,542
|
![]() |
![]() |
![]() |
![]() |
#5 |
Senior Member
Join Date: Dec 2010
Location: Verdi, Nevada
Posts: 166
|
![]()
Call Dick Crabtree. You can find him on the MAFCA website. He is the master on electrolock pop outs.
|
![]() |
![]() |
![]() |
#6 |
Senior Member
Join Date: Dec 2017
Location: Guthrie, OK
Posts: 1,145
|
![]() Sponsored Links (Register now to hide all advertisements)
|
![]() |
![]() |
![]() |
#7 |
Senior Member
Join Date: Sep 2019
Location: Fort Gratiot, Michigan
Posts: 2,296
|
![]() |
![]() |
![]() |
![]() |
#8 | |
Senior Member
Join Date: Aug 2018
Posts: 2,332
|
![]() Quote:
WD 40 is not a lubricant and may also flush away the lubricant. If WD 40 is used for this is best to re-lube. Never use WD 40 on bearings, will flush out the lube on non or poroly sealed bearings. Ran across this when a maintenance worker "lubed" a machine with WD 40, not long after all bearings failed, and the bearings spun on their shafts. |
|
![]() |
![]() |
![]() |
#9 |
Senior Member
Join Date: Jul 2010
Location: Pennsylvania
Posts: 1,100
|
![]()
I've found that I have to be careful about setting the pop out switch in the dashboard. If it's cocked in any way, or if I over tighten the three screws holding it, the lock cylinder will bind and it won't "pop" out.
|
![]() |
![]() |
![]() |
#10 |
Senior Member
Join Date: May 2010
Location: on the Littlefield
Posts: 6,159
|
![]()
Wen I had mine apart I could see the rub marks where the pot metal has swelled some I filed it down some till it all moved smoothly, I put the repro plated covers on and found I had to file the face one to have it fit original key too
|
![]() |
![]() |
![]() |
|
|
Sponsored Links (Register now to hide all advertisements) |
|