Go Back   The Ford Barn > General Discussion > Early V8 (1932-53)

Sponsored Links (Register now to hide all advertisements)

Reply
 
Thread Tools Display Modes
Old 04-01-2021, 06:21 AM   #1
mike42
Senior Member
 
mike42's Avatar
 
Join Date: Jun 2012
Location: Gaylord, Michigan
Posts: 1,599
Default '40 Brake Bleeding

Still having a hell of a time getting brakes to bleed. I tried to look at past threads, but can't find this answer.

Did someone tell me to "adjust the brakes until shoes hit the drums and then bleed......you can always re-adjust afterwards".

That's from memory right now. Am I correct ?

Thx.....Mike
mike42 is offline   Reply With Quote
Old 04-01-2021, 06:44 AM   #2
fortyfords
Senior Member
 
fortyfords's Avatar
 
Join Date: Mar 2011
Location: faucett, mo
Posts: 419
Default Re: '40 Brake Bleeding

Mike, it sounds like you have a leak somewhere or a wheel cylinder has dry rubber cups and is just letting air in every time you release the brake pedal. I would disconnect the brake line from the master cylinder and block the port and see if you get a hard pedal when you bleed. If you do get a hard pedal, then hook up one brake line at a time until you find the one wheel that gives you the soft pedal. Yes, you will have to have some plugs to block off the lines at intersections and at backing plates.
fortyfords is offline   Reply With Quote
Sponsored Links (Register now to hide all advertisements)
Old 04-01-2021, 08:03 AM   #3
mike42
Senior Member
 
mike42's Avatar
 
Join Date: Jun 2012
Location: Gaylord, Michigan
Posts: 1,599
Default Re: '40 Brake Bleeding

Forty...... thx let me check that out.....also should I adjust the brake shoes out to touch the drums ? I'll buy the plugs today. May not work on it today as we got 2" of snow last night and it's 18º now !!! Geez....

Thx....Mike
mike42 is offline   Reply With Quote
Old 04-01-2021, 08:27 AM   #4
rockfla
Senior Member
 
rockfla's Avatar
 
Join Date: Mar 2014
Location: Jacksonville FL
Posts: 3,926
Default Re: '40 Brake Bleeding

Mike42
Did you just do a "recent" brake job and or replace wheel cylinders by chance??? OR replace shoes???


As for adjusting them, I adjust the bottom first, I bring them out to where they just contact the drum and do a "very slight" back off from touching. Then do the same on the top...just ever so slightly before touching or drag!!!! It shouldn't matter IF you do this before or after bleeding!!!!


The reason for asking the first question IS. I was talking with Mike at Third Gen when I was working on my 39 Merc brakes and he was telling me about "some" of the after market shoes and wheel cylinders THAT the tabs on the shoes where they fit the wheel cylinders are a little long and thus push the cups further inward on the wheel cylinder. It allows for bleed by on the cups and you can't get a hard peddle. IF you did put new shoes and or cylinders on, you might want to pull the rubber caps on the cylinders and SEE IF there in fluid behind them......IF so (and you also replaced your shoes) you may need to pull the shoes back off and grind the tabs back a little bit!!!!!

Last edited by rockfla; 04-01-2021 at 08:32 AM.
rockfla is offline   Reply With Quote
Old 04-01-2021, 09:11 AM   #5
mike42
Senior Member
 
mike42's Avatar
 
Join Date: Jun 2012
Location: Gaylord, Michigan
Posts: 1,599
Default Re: '40 Brake Bleeding

Rock......I turned drums, replaced shoes and wheel cylinders as well as the master cylinder. i'm getting fluid to each wheel, but will not bleed as they should. I will check the tabs out for sure.

Cold and snow today so when it warms a bit.

Thx....Mike
mike42 is offline   Reply With Quote
Old 04-01-2021, 09:16 AM   #6
rockfla
Senior Member
 
rockfla's Avatar
 
Join Date: Mar 2014
Location: Jacksonville FL
Posts: 3,926
Default Re: '40 Brake Bleeding

Sponsored Links (Register now to hide all advertisements)
Quote:
Originally Posted by mike42 View Post
Rock......I turned drums, replaced shoes and wheel cylinders as well as the master cylinder. i'm getting fluid to each wheel, but will not bleed as they should. I will check the tabs out for sure.

Cold and snow today so when it warms a bit.

Thx....Mike

Also.....Are you using silicone brake fluid??? That will also make your peddle a little "softer" than normal. I was having the same issue with my Mercury.....BUT Mine ended up just being "lots" of air in the lines!!!! SO i ended up bleeding mine 4 times to get all the air out, finally a really nice peddle even with silicone fluid!!!
rockfla is offline   Reply With Quote
Old 04-01-2021, 09:21 AM   #7
rockfla
Senior Member
 
rockfla's Avatar
 
Join Date: Mar 2014
Location: Jacksonville FL
Posts: 3,926
Default Re: '40 Brake Bleeding

Mike42
Just in case, here is "from the Ford Service" book!!!!
Attached Images
File Type: jpg BrakeAdjst1.jpg (78.6 KB, 67 views)
File Type: jpg BrakeAdjst2.jpg (70.3 KB, 56 views)
File Type: jpg BrakeAdjst3.jpg (72.3 KB, 65 views)
File Type: jpg BrakeAdjst4.jpg (80.3 KB, 50 views)
rockfla is offline   Reply With Quote
Old 04-01-2021, 11:29 AM   #8
Alaska Jim
Senior Member
 
Alaska Jim's Avatar
 
Join Date: May 2010
Location: Palmer, Alaska
Posts: 1,573
Default Re: '40 Brake Bleeding

Did you "bench" bleed the master cyl. before you installed it?
Alaska Jim is offline   Reply With Quote
Old 04-03-2021, 06:15 AM   #9
mike42
Senior Member
 
mike42's Avatar
 
Join Date: Jun 2012
Location: Gaylord, Michigan
Posts: 1,599
Default Re: '40 Brake Bleeding

Rock ....thx for pages ! I'm using DOT 3 Fluid.

Alaska....I tried to bench bleed and was not very successful I'm sorry to say. That may be a big part of my problem. I have buddy looking into it now also, as I'm running out of time. As a side note I lived on Ladd Air Force Base in '51, '52 and'53 in Fairbanks. Great part of my life !!

Thx all....Mike
mike42 is offline   Reply With Quote
Old 04-03-2021, 08:14 AM   #10
mike42
Senior Member
 
mike42's Avatar
 
Join Date: Jun 2012
Location: Gaylord, Michigan
Posts: 1,599
Default Re: '40 Brake Bleeding

Rock ....

Can you send me those photos a little larger. Very hard to read when printed and some areas don't come out well at all.

[email protected]

Thx....Mike
mike42 is offline   Reply With Quote
Old 04-03-2021, 08:28 AM   #11
glennpm
Senior Member
 
glennpm's Avatar
 
Join Date: Sep 2014
Location: Wiscasset, Maine
Posts: 1,965
Default Re: '40 Brake Bleeding

My file and edits
Attached Files
File Type: pdf Brake Adjustment for 1939 - 1942_edited.pdf (1.50 MB, 85 views)
glennpm is online now   Reply With Quote
Old 04-03-2021, 10:13 AM   #12
tubman
Senior Member
 
tubman's Avatar
 
Join Date: Dec 2013
Location: Minnesota, Florida Keys
Posts: 10,259
Default Re: '40 Brake Bleeding

I have never had to bench bleed single chamber master cylinders. Didn't that come into practice only after the introduction of dual chamber masters?
tubman is online now   Reply With Quote
Old 04-03-2021, 12:12 PM   #13
Kube
Senior Member
 
Kube's Avatar
 
Join Date: May 2010
Location: Wisconsin, USA
Posts: 8,935
Default Re: '40 Brake Bleeding

Quote:
Originally Posted by tubman View Post
I have never had to bench bleed single chamber master cylinders. Didn't that come into practice only after the introduction of dual chamber masters?
You are correct sir. There is zero reason to bench bleed a single master unit.
__________________
"I can explain it for you. However, I can't understand it for you".
Kube is offline   Reply With Quote
Old 04-04-2021, 06:28 AM   #14
mike42
Senior Member
 
mike42's Avatar
 
Join Date: Jun 2012
Location: Gaylord, Michigan
Posts: 1,599
Default Re: '40 Brake Bleeding

Glenn .....thx !

I worked on it all day yesterday and I'm having a hell of a time getting anything to happen. I don't know. I may take it to my Buddy's Shop and have him see what he can do.

Thx....Mike
mike42 is offline   Reply With Quote
Old 04-04-2021, 06:30 AM   #15
mike42
Senior Member
 
mike42's Avatar
 
Join Date: Jun 2012
Location: Gaylord, Michigan
Posts: 1,599
Default Re: '40 Brake Bleeding

Glenn....printed out big and great !

Thx again...Mike
mike42 is offline   Reply With Quote
Old 04-04-2021, 08:34 AM   #16
Kurt in NJ
Senior Member
 
Kurt in NJ's Avatar
 
Join Date: May 2010
Location: on the Littlefield
Posts: 6,140
Default Re: '40 Brake Bleeding

I have found that new production wheel cylinders need to be taken apart and inspected, some have the holes drilled wrong, the feed holes drilled off center (cut the shoe tab so the piston is out more to uncover the hole??) and bleeder holes not going to the top of the cylinder --you can't get the air out!!
Even rebuilt ones need taken apart i have had leaks in them because the shavings were not cleaned out
Kurt in NJ is offline   Reply With Quote
Old 04-06-2021, 05:44 AM   #17
mike42
Senior Member
 
mike42's Avatar
 
Join Date: Jun 2012
Location: Gaylord, Michigan
Posts: 1,599
Default Re: '40 Brake Bleeding

Since the weather has been good I've tried a few more things with no luck at all ! I had it trucked down the my Buddy's shop and we'll see what he can do with it. Would sure love to be driving it with weather like we've had here !

Kurt...I'll mentioned your idea with my friend. Thx...

Mike
mike42 is offline   Reply With Quote
Old 04-06-2021, 01:25 PM   #18
Alaska Jim
Senior Member
 
Alaska Jim's Avatar
 
Join Date: May 2010
Location: Palmer, Alaska
Posts: 1,573
Default Re: '40 Brake Bleeding

Kube, tubman, I was not aware that the single chamber master cylinders did not need to be bench bled, I have always done it though. thanks for the information, good to know.--Jim
Alaska Jim is offline   Reply With Quote
Old 04-06-2021, 11:44 PM   #19
Talkwrench
Senior Member
 
Talkwrench's Avatar
 
Join Date: Aug 2012
Location: Perth, Western Australia
Posts: 2,687
Default Re: '40 Brake Bleeding

Quote:
Originally Posted by tubman View Post
I have never had to bench bleed single chamber master cylinders. Didn't that come into practice only after the introduction of dual chamber masters?
correct and dont push them all the way to the floor..
long steady strokes...
__________________
"Came too close to dying to stop living now!"
Talkwrench is offline   Reply With Quote
Old 04-07-2021, 06:14 AM   #20
51woodie
Senior Member
 
51woodie's Avatar
 
Join Date: Apr 2018
Location: Chelmsford, ON Canada
Posts: 524
Default Re: '40 Brake Bleeding

I turned drums, replaced shoes and wheel cylinders as well as the master cylinder. I'm getting fluid to each wheel, but will not bleed as they should. I will check the tabs out for sure.

Mike. I have read this post several times, and I'm not sure what the problem is. You say you can't bleed the brakes properly, so I'm going to assume you can't get a solid pedal. You say in post #5 (as above) that you turned the drums and installed new shoes. Did you have the shoes arced to match the turned drums? I'm only guessing here, but if the shoes don't match the drum radius, and only contact the drum at mid point of the shoe, is it possible that the shoe would flex, like trying to straighten out a curved spring , thus causing a soft pedal?
51woodie is offline   Reply With Quote
Reply

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump

Sponsored Links (Register now to hide all advertisements)


All times are GMT -5. The time now is 09:55 AM.