|
Sponsored Links (Register now to hide all advertisements) |
|
|
Thread Tools | Display Modes |
12-27-2015, 06:56 AM | #1 |
Senior Member
Join Date: May 2010
Posts: 2,871
|
'40 coupe upholstery question
What is the round trim around the interior of the door frame opening called ? Is it wind lace, or weather strip ?
Is there a good book on the Ford interior upholstery construction that shows how the headliner, door weather seal or wind lace is installed ? Where do you find it ? Thank you Fodbarners. |
12-27-2015, 07:18 AM | #2 |
Senior Member
Join Date: May 2010
Location: Columbia, SC
Posts: 1,579
|
Re: '40 coupe upholstery question
Believe it's called windlace, and I'm sure Lebaron Bonney has it. They can probably also provide information on installation. As I recall, the portion above the door hooks to pointed ears on the door tins.
|
Sponsored Links (Register now to hide all advertisements) |
|
12-27-2015, 11:03 AM | #3 |
Senior Member
Join Date: May 2010
Location: Alabama
Posts: 3,260
|
Re: '40 coupe upholstery question
It's held in by tacking it to the body via the tack strip attached to the body. The tins that screw to the body with the pointed claws are there for the headliner.
|
12-27-2015, 12:21 PM | #4 |
Senior Member
Join Date: May 2010
Location: Coral Springs FL
Posts: 10,942
|
Re: '40 coupe upholstery question
russcc: This will help. I used these instructions that came with my 1940 interior kit back in 1988. Practice making the 45 degree miter cuts on scrap wind lace before you install it. From the looks of the photos I think I used Contact cement to also hold the wind lace in place.
Last edited by 19Fordy; 12-27-2015 at 12:53 PM. |
12-27-2015, 12:24 PM | #5 |
Senior Member
Join Date: May 2010
Location: Coral Springs FL
Posts: 10,942
|
Re: '40 coupe upholstery question
More photos: Paint your headliner bows to prevent rust stains. They are numbered.
Last edited by 19Fordy; 12-27-2015 at 12:38 PM. |
12-27-2015, 12:31 PM | #6 |
Senior Member
Join Date: May 2010
Location: Coral Springs FL
Posts: 10,942
|
Re: '40 coupe upholstery question
Sponsored Links (Register now to hide all advertisements)
Last edited by 19Fordy; 12-27-2015 at 01:06 PM. |
12-27-2015, 12:45 PM | #7 |
Senior Member
Join Date: May 2010
Location: Napa,California
Posts: 6,037
|
Re: '40 coupe upholstery question
If the prongs to hold the windlace are missing use pop rivets to hold it. Be sure to replace all the old tack strips. You can get the new material from Drake and other suppliers. Using the old original brittle strips in the car will cause you grief. Tacks and staples will no hold and eventually as the door pushes against the windlace it will come loose. You only want to do the job once.
|
12-27-2015, 03:12 PM | #8 |
Senior Member
Join Date: May 2010
Location: Coral Springs FL
Posts: 10,942
|
Re: '40 coupe upholstery question
"After" photos of mitered wind lace. Click "twice" on photo for good close up view.
|
12-27-2015, 03:41 PM | #9 |
Senior Member
Join Date: May 2010
Location: Palm Harbor, Fl
Posts: 137
|
Re: '40 coupe upholstery question
Do the Tudor sedans have the headliner attaching tins too? What creates the straight headliner edge shown over the windlace?
|
12-27-2015, 03:56 PM | #10 | |
Senior Member
Join Date: May 2010
Location: Coral Springs FL
Posts: 10,942
|
Re: '40 coupe upholstery question
Quote:
You can see the screw holes in the tin strip photos. That thin metal trim strip has a radiused edge along its bottom edge and the headliner gets tucked up underneath that bottom edge thereby forming a straight edge as needed. OTHER FORDBARNERS PLEASE CORRECT ME IF I AM WRONG AS I CAN'T QUITE REMEMBER WITH ABSOLUTE CERTAINTY. Last edited by 19Fordy; 12-27-2015 at 04:08 PM. |
|
12-28-2015, 09:48 AM | #11 |
Senior Member
Join Date: Jun 2011
Location: central Iowa
Posts: 484
|
Re: '40 coupe upholstery question
Yes sedans use tins and 19Fordy's advise is very good.
__________________
Louvering, bias ply tire-truing, metal shaping and forming, lathe and mill work, member shop HAGERTY Ins. expert repair network. High quality paint work in Iowa. |
12-28-2015, 10:00 AM | #12 |
Senior Member
Join Date: May 2010
Location: Napa,California
Posts: 6,037
|
Re: '40 coupe upholstery question
The tin strips have what I call "shark teeth" on the back side. That is what grabs the headliner after it is tucked underneath. Some of the teeth become bent so they should be straightened to match the others. All 40 passenger cars have these strips. I should mention that there is also a tack strip on the front windshield header. This one should also be replaced as by now the original is shot.
|
12-29-2015, 12:07 PM | #13 |
Member
Join Date: Feb 2011
Location: north,royalton ohio
Posts: 84
|
Re: '40 coupe upholstery question
GO to www. how-to-build-hotrods.com look under shawn appleman aka " SKIPSTICH" HE HAS THE ANSWER YOU NEED AND PICS HEADLINER-INSTALLATION HOPE THIS HELP YOU REAGEN
|
06-14-2021, 08:52 AM | #14 |
Member
Join Date: Oct 2020
Location: Cozumel and Deming N.M.
Posts: 87
|
Re: '40 coupe upholstery question
Going thru this myself right now. All info posted so far is way good.Same as what I found. However I could not figure out my back window,how to trim it or attach it. Turns out you have to pull the back window,yikes.
Also mine is a 41 sedan. May not be the same. I recently ordered a headliner from a company. Came in wrong? Not sure probably my mistake. Apparently there is a difference in a tudor and a tudor two door.One has 6 hoops and one has 7. They got me there. The windlace in my opinion is not necessary unless the attachment methods mentioned previously by window frames etc are not any good. |
06-14-2021, 11:43 AM | #15 |
Senior Member
Join Date: May 2010
Location: Coral Springs FL
Posts: 10,942
|
Re: '40 coupe upholstery question
I am not sure what you mean when you say, "The windlace in my opinion is not necessary unless the attachment methods mentioned previously by window frames etc are not any good."
If you're going to go to the trouble to install a new headliner, it will look fresh and new with new wind lace installed. |
06-14-2021, 02:12 PM | #16 |
Senior Member
Join Date: Sep 2010
Posts: 492
|
Re: '40 coupe upholstery question
I ordered a headliner from these guys. dimensions are right on, quality and color just what I wanted.
https://wlsheadliners.com/ For nice cloth windlace in the same patterns once avaialble from Lebaron Bonney try these folks. Knowledgable staff, friendly folks, fast service, very reasonable prices, about 1/2 what the "usual suspects" want. https://www.albrightssupply.com/ Good luck, don't be shy about asking for samples from either one. |
06-14-2021, 02:15 PM | #17 |
Member
Join Date: Oct 2020
Location: Cozumel and Deming N.M.
Posts: 87
|
Re: '40 coupe upholstery question
I was thinking that if headliner tucks behind window trim that windlace would not be necessary. On my car I can tuck it behind front and back side windows. The center post has a covered panel I guess you would call it, that the short part of the headliner will tuck behind also.
The rear goes out the rear window and the new rubber covers the egde. The front windshield trim covers it also. I agree the windlace dresses it up but I am guessing not all installs are the same. Also consider my opinion as only based on one car,mine. So really I dont know much. |
06-14-2021, 03:07 PM | #18 |
Junior Member
Join Date: Jun 2021
Location: Pittsburgh, PA
Posts: 15
|
Re: '40 coupe upholstery question
Thanks for posting this. Very helpful.
|
06-14-2021, 10:12 PM | #19 |
Senior Member
Join Date: May 2010
Location: Coral Springs FL
Posts: 10,942
|
Re: '40 coupe upholstery question
I have never seen wind lace used anywhere else except around door openings. Never around windows.
|
06-18-2021, 12:11 PM | #20 |
Senior Member
Join Date: Sep 2010
Posts: 492
|
Re: '40 coupe upholstery question
This is right, door openings. I'd imagine a rather dismal driving experience without it. Now, in some high end cars (Packard, Lincolns of the 30s) there was a small diameter coachlace covered welt cord that was a finsih between select parts of the interior. Very stylish in a proper setting. Packard also had a small welt cord behind the door panels. Seldom to never the case in our beloved bread and butter Fords.
|
|
|
Sponsored Links (Register now to hide all advertisements) |
|