Go Back   The Ford Barn > General Discussion > Early V8 (1932-53)

Sponsored Links (Register now to hide all advertisements)

Reply
 
Thread Tools Display Modes
Old 05-28-2020, 12:19 AM   #1
Brian
Senior Member
 
Brian's Avatar
 
Join Date: May 2010
Location: Masterton, New Zealand
Posts: 3,816
Default brake problem

I've been converting my 35 to Bendix style brakes. I cannot get a pedal....
I am convinced the RH front wheel cylinder is bad.
Long story, but I'll try to give all relevant details to enable you to make a diagnosis.
Master cylinder and all wheel cylinders were purchased from Summit. When they arrived, the m/c was made in Taiwan, all wheel cyl's were chink.
Master cylinder 1 1/16 bore. Front wheel cylinders 1 1/8 bore. Rear w/c's 7/8 bore.
I am running a remote reservoir up on the firewall with a line into top of m/c.

Fitted everything up to discover the rear wheel cyl's were tapped 3/8 24 UNF. Does not suit the 7/16 tube nuts required for Ford 1/4" lines.

Ordered more rear cylinders from James @ Gotham City...
Fitted them and plumbed up.
Attempted to bleed all brakes. No pedal.
By a process of elimination; plug the tee at back of master cylinder that runs to front brakes, I could get a good hard, high pedal which indicates to me that the rear brakes are 'sweet'. Plumb in the front brakes, pedal goes to floor. No leaks apparent anywhere. Reading on here that some chinkee cylinders don't have the bleed nipple at top of bore, I've unbolted front cylinders from backing plates, leaving the hoses attached, removed the links and boots, and used Gclamps and plastic endcaps to prevent the pistons from being blown outta the bores, I again bled the cylinders, being able to position them in various positions to preclude the possibility of any air remaining. Good hard, high pedal.
Left overnite. Next morning, pedal was still the same, so removed Gclamps etc, fitted links and boots, bolted wheel cylinders back onto backing plates, refitted shoes, springs drums. Still a good hard pedal. Left overnite....
This morning still the same, so refitted wheels, took car for a spin; pedal goes to floor. Only the rear brakes would lock up on my gravel driveway.
Back home, attempt to bled brakes; no air is coming out, only fluid.
If I clamp visegrips on the rh hose, pedal is high and hard. This indicates to me that the rh cylinder, I dunno, seems to be sucking air in somewhere. Again, no sign of leakage anywhere.
This rather long narrative is really a very condensed account of what I've been attempting for the past two months.
I am sure that James at Gotham City could supply 'decent' cylinders, but it is impossible to get anything from the US of late [no planes].
Or....have I diagnosed this incorrectly?
Bear in mind, my car is RHD; the brake line Tee's off off the RH side to the RH wheel before continuing around to the LHS
__________________
Unfortunately, two half wits don't make a whole wit!
Brian is offline   Reply With Quote
Old 05-28-2020, 01:30 AM   #2
Brian
Senior Member
 
Brian's Avatar
 
Join Date: May 2010
Location: Masterton, New Zealand
Posts: 3,816
Default Re: brake problem

Using 39 pedal assembly, and yes, I have a bit of free travel before pushrod contacts end of m/c piston
__________________
Unfortunately, two half wits don't make a whole wit!
Brian is offline   Reply With Quote
Sponsored Links (Register now to hide all advertisements)
Old 05-28-2020, 01:59 AM   #3
Mr 42
Senior Member
 
Mr 42's Avatar
 
Join Date: May 2010
Location: Sweden
Posts: 427
Default Re: brake problem

Is everything adjusted properly?
Do you have a cracked brake drum, let a friend brake and put you hands on the drum.
Problems withe the bake hose ,let a friend brake and put you hands on the brake hose.

Switch the cylinders left to right, and see if the fault follows the cylinder.
Mr 42 is offline   Reply With Quote
Old 05-28-2020, 05:05 AM   #4
Ggmac
Senior Member
 
Join Date: Jul 2016
Location: Lake worth Florida
Posts: 1,073
Default Re: brake problem

Possible need of residual valves ?
Ggmac is offline   Reply With Quote
Old 05-28-2020, 07:01 AM   #5
1931 flamingo
Senior Member
 
1931 flamingo's Avatar
 
Join Date: May 2010
Location: new britain,ct 06052
Posts: 9,389
Default Re: brake problem

A while back some brake cyls were made wrong, something about the bleed or return hole in the wrong place...............
Paul in CT
1931 flamingo is offline   Reply With Quote
Old 05-28-2020, 08:04 AM   #6
51 MERC-CT
Senior Member
 
51 MERC-CT's Avatar
 
Join Date: May 2010
Location: East Hartford, Ct
Posts: 5,898
Default Re: brake problem

Sponsored Links (Register now to hide all advertisements)
You have not said whether you have a single or dual master cylinder installed.
In a similar situation with a dual master cylinder installed the solution was to install 'Speed bleeders' and bleed accordingly.
This may or may not work but may be worth a shot.
Why are you using 1/4" brake lines??



Attached Images
File Type: jpg SPEED BLEEDERS.jpg (85.5 KB, 371 views)
__________________
DON'T RECALL DOING SOMETHING FOR MYSELF BASED ON SOMEONE ELSE'S LIKES OR DISLIKES

Last edited by 51 MERC-CT; 05-28-2020 at 08:21 AM.
51 MERC-CT is offline   Reply With Quote
Old 05-28-2020, 10:13 AM   #7
rich b
Senior Member
 
rich b's Avatar
 
Join Date: May 2010
Location: Minnesota
Posts: 1,813
Default Re: brake problem

What kind of Bendix brakes?

What adjustment procedure are you using?

Anchor pin adjusted to center the shoes?

Adjust the brakes tight and see where the pedal goes.
rich b is offline   Reply With Quote
Old 05-28-2020, 01:20 PM   #8
Brian
Senior Member
 
Brian's Avatar
 
Join Date: May 2010
Location: Masterton, New Zealand
Posts: 3,816
Default Re: brake problem

Brake drums not cracked, they are nos
Residual valves? Why? isn't the residual valve built into the m/c? And, having the remote reservoir mounted up on the firewall actually adds a slight 'head'.
Brake cylinders made wrong? Yes, I am convinced these w/c's are wrong. Only way I can bleed all air out, is to unbolt from back plates, whilst still attached to hoses, G clamp across ends of cylinders to prevent pistons popping out, and 'manipulating' them into such a position as to get all air out. Re-assemble everything, still good. Drive the 'beast' and upon first application of brakes, pedal goes to floor!
Single circuit, Lockheed style m/c with 1 1/16 bore.
Why 1/4" lines? Dunno, ask Henry Ford.
Speed bleeders could be a bit hard to get out of the USA right now, I have, during all my efforts, wrapped thread tape around the threads of all the bleed nipples.
39 Lincoln brakes
Yes, have set all shoes hard out against drums and set handbrake, and had good hard, high pedal. Then, when I drive this thing and apply brakes, pedal goes to floor. Repeated pumping brings about a spongy pedal that still goes to floor.
Much angst!!
__________________
Unfortunately, two half wits don't make a whole wit!
Brian is offline   Reply With Quote
Old 05-28-2020, 03:34 PM   #9
Mr 42
Senior Member
 
Mr 42's Avatar
 
Join Date: May 2010
Location: Sweden
Posts: 427
Default Re: brake problem

NOS does not mean Not Cracked.
Have you checked them?
Mr 42 is offline   Reply With Quote
Old 05-28-2020, 03:44 PM   #10
Ggmac
Senior Member
 
Join Date: Jul 2016
Location: Lake worth Florida
Posts: 1,073
Default Re: brake problem

Not all mc have built in residual valves . But i understand your arrangement and the remote fill should work . I would remove the wheel cyl in question and disassemble to inspect the bore , cups and machining .
I just went through a similar, no pedal , on a 30 with juice brakes . All i did was replace some flex lines , bleed and results were a mushy pedal . After much frustration and pulling of my hair . I installed residual valves and problem solved . Mind you this same setup worked for 10-12 yrs until i changed the lines .
Ggmac is offline   Reply With Quote
Old 05-28-2020, 04:03 PM   #11
FlatheadTed
Senior Member
 
FlatheadTed's Avatar
 
Join Date: May 2010
Location: Auckland
Posts: 4,691
Send a message via AIM to FlatheadTed
Default Re: brake problem

Cylinders The problem with the repoped ones was the inlet hole was larger than stock and the cup straddled the hole so when new linings were used the cup was bushed back over them ,My current brake job one wheel had that problem .solution grind a bit of the end of the shoe 3/32 ,
__________________
http://www.flatheadted.com


Flathead Ted brake Floaters ,

Last edited by FlatheadTed; 05-28-2020 at 06:34 PM.
FlatheadTed is offline   Reply With Quote
Old 05-28-2020, 04:07 PM   #12
JSeery
Member Emeritus
 
JSeery's Avatar
 
Join Date: Nov 2012
Location: Wichita KS
Posts: 16,132
Default Re: brake problem

"Only way I can bleed all air out, is to unbolt from back plates, whilst still attached to hoses, G clamp across ends of cylinders to prevent pistons popping out, and 'manipulating' them into such a position as to get all air out."

Brian, that is not a usable part or bleeding process. I know you were just attempting to get it bleed, but over time you don't want to be disassembling the whole brake system every time in needs to be bleed. You need good quality wheel cylinders, but no idea where they would come from in England!
JSeery is offline   Reply With Quote
Old 05-28-2020, 04:08 PM   #13
FlatheadTed
Senior Member
 
FlatheadTed's Avatar
 
Join Date: May 2010
Location: Auckland
Posts: 4,691
Send a message via AIM to FlatheadTed
Default Re: brake problem

Displacement Mismatched m/c or pipes to large ,1/4 is ok .
__________________
http://www.flatheadted.com


Flathead Ted brake Floaters ,
FlatheadTed is offline   Reply With Quote
Old 05-28-2020, 04:38 PM   #14
Kurt in NJ
Senior Member
 
Kurt in NJ's Avatar
 
Join Date: May 2010
Location: on the Littlefield
Posts: 6,140
Default Re: brake problem

Take apart wheel cylinders and inspect to see if holes drilled properly--- the bleeder hole at top, the fluid hole in center---- some have bleeder hole drilled 1/2 way down, some fluid holes drilled to be under cup, I always take apart new wheel cylinders-- and rebuilt ones for inspection, the new ones many times have the holes drilled wrong, the resleeved ones have honing grindings not cleaned out
Kurt in NJ is offline   Reply With Quote
Old 05-30-2020, 07:00 PM   #15
cas3
Senior Member
 
Join Date: Jan 2011
Location: sw minnesota
Posts: 4,541
Default Re: brake problem

what did you find brian? i know you are not sitting still !
cas3 is offline   Reply With Quote
Old 05-30-2020, 08:05 PM   #16
FlatheadTed
Senior Member
 
FlatheadTed's Avatar
 
Join Date: May 2010
Location: Auckland
Posts: 4,691
Send a message via AIM to FlatheadTed
Default Re: brake problem

Brian is in New Zealand thats about 1.1/2 hrs from Australia about 14hrs from the USA and about the same from England ,Don't forget We have always supported the USA ideals , fought in support in the war ect ,
Quote:
Originally Posted by JSeery View Post
"Only way I can bleed all air out, is to unbolt from back plates, whilst still attached to hoses, G clamp across ends of cylinders to prevent pistons popping out, and 'manipulating' them into such a position as to get all air out."

Brian, that is not a usable part or bleeding process. I know you were just attempting to get it bleed, but over time you don't want to be disassembling the whole brake system every time in needs to be bleed. You need good quality wheel cylinders, but no idea where they would come from in England!
__________________
http://www.flatheadted.com


Flathead Ted brake Floaters ,
FlatheadTed is offline   Reply With Quote
Old 05-30-2020, 08:08 PM   #17
JSeery
Member Emeritus
 
JSeery's Avatar
 
Join Date: Nov 2012
Location: Wichita KS
Posts: 16,132
Default Re: brake problem

Yep, need to stay awake here!!

Last edited by JSeery; 05-30-2020 at 09:16 PM.
JSeery is offline   Reply With Quote
Old 05-30-2020, 08:19 PM   #18
FlatheadTed
Senior Member
 
FlatheadTed's Avatar
 
Join Date: May 2010
Location: Auckland
Posts: 4,691
Send a message via AIM to FlatheadTed
Default Re: brake problem

Thanks , No offence meant Jerry ,
__________________
http://www.flatheadted.com


Flathead Ted brake Floaters ,
FlatheadTed is offline   Reply With Quote
Old 05-30-2020, 09:22 PM   #19
51504bat
Senior Member
 
51504bat's Avatar
 
Join Date: Sep 2013
Location: SoCal-Redlands
Posts: 2,997
Default Re: brake problem

Quote:
Originally Posted by FlatheadTed View Post
Brian is in New Zealand thats about 1.1/2 hrs from Australia about 14hrs from the USA and about the same from England ,Don't forget We have always supported the USA ideals , fought in support in the war ect ,

Not that many Americans realize that what good allies Australia and New Zealand are.They have always been there for the US. Thanks from a vet.
__________________
Making the simple complicated for over 30 years.
51504bat is online now   Reply With Quote
Old 05-30-2020, 09:27 PM   #20
JSeery
Member Emeritus
 
JSeery's Avatar
 
Join Date: Nov 2012
Location: Wichita KS
Posts: 16,132
Default Re: brake problem

This was not intended as an internal incident, just a stupid mistake! For some strange reason I was thinking Brian lived in England (I know, it says New Zealand right under his name!). And on top of that I knew Brian lives in New Zealand, just one of those things, doing too many things at once.

And I still think he needs new (as in correctly built) wheel cylinders! LOL

Last edited by JSeery; 05-30-2020 at 09:32 PM.
JSeery is offline   Reply With Quote
Old 05-30-2020, 10:04 PM   #21
Brian
Senior Member
 
Brian's Avatar
 
Join Date: May 2010
Location: Masterton, New Zealand
Posts: 3,816
Default Re: brake problem

Actually, I haven't been sitting still; just been doing other things [Ford V8 flattie related] for other people. Having a break [brake lol] from this little dilemma. I have had quite a few fellows tell me my master cylinder is the offending item; this I doubt, however, I am going to remove a mates master cylinder from under his 39 Mercury [a known good cylinder], and swap into my car. Process of elimination....
__________________
Unfortunately, two half wits don't make a whole wit!
Brian is offline   Reply With Quote
Old 05-31-2020, 10:10 PM   #22
rich b
Senior Member
 
rich b's Avatar
 
Join Date: May 2010
Location: Minnesota
Posts: 1,813
Default Re: brake problem

Maybe try it without the hose and remote reservoir hooked up.
rich b is offline   Reply With Quote
Sponsored Links (Register now to hide all advertisements)
Old 05-31-2020, 11:13 PM   #23
Brian
Senior Member
 
Brian's Avatar
 
Join Date: May 2010
Location: Masterton, New Zealand
Posts: 3,816
Default Re: brake problem

Today noticed wet spots bottom of both front backing plates. So front cylinders are leaking. Chinese rubbish bought from Summit. I have a wanted advert in the swap meet section. If anyone can suggest where to get decent front cylinders, I'll appreciate it.
__________________
Unfortunately, two half wits don't make a whole wit!
Brian is offline   Reply With Quote
Old 06-01-2020, 12:43 AM   #24
flatheadmurre
Senior Member
 
flatheadmurre's Avatar
 
Join Date: Apr 2015
Location: Sweden
Posts: 3,045
Default Re: brake problem

Before shipping across the ocean take a look at what you have...usually when leaking nowdays is when honing is either out of size or to coarse.
If it´s to coarse you can fix that put in a new set of cups and be on the road.
flatheadmurre is offline   Reply With Quote
Old 06-01-2020, 01:45 AM   #25
petehoovie
Senior Member
 
petehoovie's Avatar
 
Join Date: May 2015
Posts: 7,924
Default Re: brake problem

DOT 3 or DOT 5?....
__________________
The only thing nice about being imperfect is the joy it brings to others....

"Silver rings, your butt! Them's washers!"
"We shot our way out of that town for a dollar's worth of steel holes!" - from 'The Wild Bunch' - 1969

https://www.youtube.com/watch?v=7NReUd2_0u0
petehoovie is offline   Reply With Quote
Old 06-01-2020, 02:09 AM   #26
dumb person
Senior Member
 
dumb person's Avatar
 
Join Date: Apr 2011
Location: South pacific island
Posts: 1,724
Default Re: brake problem

Sponsored Links (Register now to hide all advertisements)
If you cannot get good replacements any time soon. see if you can get replacement seals.
And if the bleed was not quite at the top, would it be possible to fill the offending air gap with epoxy?
__________________
<Link> This is how we roll<Link>

"I'm Convinced that no one really reads posts anymore; they just fabricate what they think the post says then ramble on about red herrings."--Bob
Outcasts rules of old cars
#1 Fun is imperative, mainstream is overrated
#2 If they think it is impossible, prove them wrong
#3 If the science says it impossible you are not being creative enough.
#4 No shame in recreating something you never had
#5 If it were not for the law & physics you would be unstoppable
dumb person is offline   Reply With Quote
Old 06-04-2020, 06:08 PM   #27
Brian
Senior Member
 
Brian's Avatar
 
Join Date: May 2010
Location: Masterton, New Zealand
Posts: 3,816
Default Re: brake problem

Update; I bought locally some new 1 1/8 cups. replaced the cups in the front wheel cylinders with them. The new cups measure approx .025" bigger than the Chinese things. I think the problem is now resolved...raining here [lovely winters day], so have not road tested.
I wish to thank everyone who contributed with ideas, that's what makes this forum so great! A wealth of knowledge.
__________________
Unfortunately, two half wits don't make a whole wit!
Brian is offline   Reply With Quote
Old 06-04-2020, 06:49 PM   #28
Talkwrench
Senior Member
 
Talkwrench's Avatar
 
Join Date: Aug 2012
Location: Perth, Western Australia
Posts: 2,687
Default Re: brake problem

Fingers crossed thats it Brian!
__________________
"Came too close to dying to stop living now!"
Talkwrench is offline   Reply With Quote
Old 06-06-2020, 06:31 PM   #29
41panelmark
Senior Member
 
41panelmark's Avatar
 
Join Date: May 2010
Location: Colorado
Posts: 1,264
Default Re: brake problem

Quote:
Originally Posted by Brian View Post
Update; I bought locally some new 1 1/8 cups. replaced the cups in the front wheel cylinders with them. The new cups measure approx .025" bigger than the Chinese things. I think the problem is now resolved...raining here [lovely winters day], so have not road tested.
I wish to thank everyone who contributed with ideas, that's what makes this forum so great! A wealth of knowledge.
Where did you get your replacement cups? Napa no longer carries just the rebuild kits for some reason and yes the repops seem to be smaller in comparison.
41panelmark is offline   Reply With Quote
Old 06-06-2020, 06:45 PM   #30
JSeery
Member Emeritus
 
JSeery's Avatar
 
Join Date: Nov 2012
Location: Wichita KS
Posts: 16,132
Default Re: brake problem

At one time you could purchase just the cups by diameter. Ebay seems to have them as well as some brake specialty suppliers. https://americanbrakecorp.com/wheel_...bber_cups.html
JSeery is offline   Reply With Quote
Old 06-06-2020, 06:58 PM   #31
41panelmark
Senior Member
 
41panelmark's Avatar
 
Join Date: May 2010
Location: Colorado
Posts: 1,264
Default Re: brake problem

Thank you, this helps a lot.
41panelmark is offline   Reply With Quote
Old 06-06-2020, 07:28 PM   #32
Brian
Senior Member
 
Brian's Avatar
 
Join Date: May 2010
Location: Masterton, New Zealand
Posts: 3,816
Default Re: brake problem

I'm in New Zealand, so unable to assist you in advising where to purchase rebuild parts. Let me tell you this...sign of the times...I too had trouble sourcing these components which were so readily available in years past. Everything today seems to just be catering for the throwaway society...people no longer rebuilt stuff, merely replace their worn out 'old' stuff with the latest and greatest new version.
My latest 'issue' with this job is the brake linings the franchised brake specialist bonded onto the shoes I supplied. Some sort of black lining, very dusty, and the dust sort of smears over the lining as a crusty glaze. I've sent them back and they can put something decent on...
When the 35 still had mechanical brakes, I got the local garage [who have a brake dept], to bond some new linings onto my shoes. Same bloody stuff!! and I had no brakes!! Absolutely no braking effect, lots of pedal, but no retardation. And, it heated the drums so much that the powder coating on my wheels melted.
I ended up supplying old style woven asbestos linings and they re-did the job. [charged me again too, the mongrels!!]
Just so hard to source quality parts anymore....
__________________
Unfortunately, two half wits don't make a whole wit!
Brian is offline   Reply With Quote
Old 06-06-2020, 08:38 PM   #33
JSeery
Member Emeritus
 
JSeery's Avatar
 
Join Date: Nov 2012
Location: Wichita KS
Posts: 16,132
Default Re: brake problem

How long ago was that Brian, thought they were really against asbestos, in Australia at least, from the import stories posted on here?
JSeery is offline   Reply With Quote
Old 06-07-2020, 02:17 AM   #34
flatheadmurre
Senior Member
 
flatheadmurre's Avatar
 
Join Date: Apr 2015
Location: Sweden
Posts: 3,045
Default Re: brake problem

There are plenty of good friction material available...just have to ask the right questions buying it and not from a modern brakeshop...
It´s become real difficult to find a modern material for rivetting though.
For bonded material look for industrial...elevators still use drum brakes.
High friction is what we want...longevity is secondary.
flatheadmurre is offline   Reply With Quote
Old 06-07-2020, 02:20 AM   #35
dumb person
Senior Member
 
dumb person's Avatar
 
Join Date: Apr 2011
Location: South pacific island
Posts: 1,724
Default Re: brake problem

Bonded is normally bad, although i had bonded stuff that was like cardboard. It had heaps of grip & made for amazing brakes. Last 10 months and it was worn out.
I then went to the truck shop & asked for woven lining.

TLR Truck shop woven lining comes at a price but is.. worth it?
__________________
<Link> This is how we roll<Link>

"I'm Convinced that no one really reads posts anymore; they just fabricate what they think the post says then ramble on about red herrings."--Bob
Outcasts rules of old cars
#1 Fun is imperative, mainstream is overrated
#2 If they think it is impossible, prove them wrong
#3 If the science says it impossible you are not being creative enough.
#4 No shame in recreating something you never had
#5 If it were not for the law & physics you would be unstoppable
dumb person is offline   Reply With Quote
Old 06-07-2020, 02:32 AM   #36
Brian
Senior Member
 
Brian's Avatar
 
Join Date: May 2010
Location: Masterton, New Zealand
Posts: 3,816
Default Re: brake problem

JSeery, Yes, the Aussies are really down on asbestos. Here in NZ we can still import a car without every component being stripped down to check for the dreaded asbestos, unlike our cousins across the ditch.
__________________
Unfortunately, two half wits don't make a whole wit!
Brian is offline   Reply With Quote
Old 06-07-2020, 01:19 PM   #37
JSeery
Member Emeritus
 
JSeery's Avatar
 
Join Date: Nov 2012
Location: Wichita KS
Posts: 16,132
Default Re: brake problem

Quote:
Originally Posted by Brian View Post
JSeery, Yes, the Aussies are really down on asbestos. Here in NZ we can still import a car without every component being stripped down to check for the dreaded asbestos, unlike our cousins across the ditch.
That's good. I would not be happy with someone else dismantling my vehicle!
JSeery is offline   Reply With Quote
Old 06-07-2020, 07:41 PM   #38
Talkwrench
Senior Member
 
Talkwrench's Avatar
 
Join Date: Aug 2012
Location: Perth, Western Australia
Posts: 2,687
Default Re: brake problem

Quote:
Originally Posted by JSeery View Post
That's good. I would not be happy with someone else dismantling my vehicle!
Yes its happened to one of our Ford Barn members and a friend who just lives around the corner from me. I'll let him tell the story , but to add insult to injury he also received a fine, let me tell you it wasn't small..
__________________
"Came too close to dying to stop living now!"
Talkwrench is offline   Reply With Quote
Old 06-07-2020, 08:04 PM   #39
phil pavicich
Member
 
Join Date: Aug 2010
Location: australia
Posts: 58
Default Re: brake problem

Yes that was me , i imported a 34 5w from south africa , i had asked the elderly gentleman 80 year old who i bought it of to remove the brake shoes of the car and remove clutch plate , Which he did , but he put them in a cardboard box and left them in the car as he thought i would need them again, any way when the car cam into Fremantle Australia , border force went thru it , they wanted a independant asbestos company to check for asbestos , to cut a long story short , it took 4 weeks of fucking around with asbestos companys and border force , i was charged for asbestos inspection fees , removal fees , recheck fees ,storage fees from container company , storage fees from border force , and then a fine from border force for importing a car into australia with asbestos, total was $12000 aussie $$,i went to my local member for parliment , and they said we cant go against another gov department and told me to pay the fine , fuck the government and there asbestos crap
phil pavicich is offline   Reply With Quote
Old 06-07-2020, 08:37 PM   #40
Brian
Senior Member
 
Brian's Avatar
 
Join Date: May 2010
Location: Masterton, New Zealand
Posts: 3,816
Default Re: brake problem

I feel for you Phil...Aust $12,000 !! did they find the asbestos in the head gaskets? What a dangerous car you imported!!
It's way over the top isn't it?
I enquired to our NZ Customs if I could import asbestos brake linings- NO WAY!!
About three years ago I purchased a NOS cluster on eBay off an American seller. I got him to send it to an American forwarding outlet that works in with NZ Post. They refused to send it to me because it had Cosmoline on it. I had to supply MHSD information, lots of toing and froing, said they'd destroy it at no charge to me, alternatively return it to the vendor at half the price it would have cost to send to NZ. I got them to send it back to him, told him to keep it. Unfortunately, this is all for our personal safety you understand?
__________________
Unfortunately, two half wits don't make a whole wit!
Brian is offline   Reply With Quote
Reply

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump

Sponsored Links (Register now to hide all advertisements)


All times are GMT -5. The time now is 09:31 AM.