Go Back   The Ford Barn > General Discussion > Early V8 (1932-53)

Sponsored Links (Register now to hide all advertisements)

Reply
 
Thread Tools Display Modes
Old 12-03-2021, 10:12 AM   #1
32truck
Junior Member
 
32truck's Avatar
 
Join Date: Nov 2021
Location: Tampa bay
Posts: 28
Default Aluminum pulley for M90 blower.

Well while I have the distributor out waiting for charlieNY to check it out, on to the next issue. My blower pulley is damaged because some numb nuts didnt have it tight and wallowed out the keyway. Any ideas where to get something like this? I know it's a v belt on a blower but I'd rather not completely change the belt set up.


Andy

Sent from my SM-N986U using Tapatalk
32truck is offline   Reply With Quote
Old 12-03-2021, 11:02 AM   #2
Bored&Stroked
Senior Member
 
Bored&Stroked's Avatar
 
Join Date: Jan 2011
Location: Central Ohio
Posts: 5,012
Default Re: Aluminum pulley for M90 blower.

You'll probably need to have one custom made at a machine shop. Not a hard thing to do - but they'll need exact measurements on the shaft and keyway.
Bored&Stroked is offline   Reply With Quote
Sponsored Links (Register now to hide all advertisements)
Old 12-03-2021, 11:56 AM   #3
marko39
Senior Member
 
Join Date: Oct 2016
Location: harpursville ny
Posts: 1,038
Default Re: Aluminum pulley for M90 blower.

What is the pully diameter? And bore? Does it have to be aluminum ?
marko39 is offline   Reply With Quote
Old 12-03-2021, 11:58 AM   #4
Brian
Senior Member
 
Brian's Avatar
 
Join Date: May 2010
Location: Masterton, New Zealand
Posts: 3,816
Default Re: Aluminum pulley for M90 blower.

Or, [machine work again] simply bore it out, press in a sleeve, [ideally steel - more durable], scotch key it in place, bore and key it to suit...
__________________
Unfortunately, two half wits don't make a whole wit!
Brian is offline   Reply With Quote
Old 12-03-2021, 12:36 PM   #5
solidaxle
Senior Member
 
solidaxle's Avatar
 
Join Date: Mar 2011
Location: upstate NY
Posts: 475
Default Re: Aluminum pulley for M90 blower.

Consider yourself lucky it didn't fly off going down the road.
solidaxle is offline   Reply With Quote
Old 12-03-2021, 12:37 PM   #6
32truck
Junior Member
 
32truck's Avatar
 
Join Date: Nov 2021
Location: Tampa bay
Posts: 28
Default Re: Aluminum pulley for M90 blower.

Sponsored Links (Register now to hide all advertisements)
Quote:
Originally Posted by marko39 View Post
What is the pully diameter? And bore? Does it have to be aluminum ?
Bore .640 pulley diameter 4inches. Nah doesn't have to be aluminum.

Sent from my SM-N986U using Tapatalk
32truck is offline   Reply With Quote
Old 12-03-2021, 12:38 PM   #7
32truck
Junior Member
 
32truck's Avatar
 
Join Date: Nov 2021
Location: Tampa bay
Posts: 28
Default Re: Aluminum pulley for M90 blower.

Quote:
Originally Posted by solidaxle View Post
Consider yourself lucky it didn't fly off going down the road.
No doubt!

Sent from my SM-N986U using Tapatalk
32truck is offline   Reply With Quote
Old 12-03-2021, 12:40 PM   #8
32truck
Junior Member
 
32truck's Avatar
 
Join Date: Nov 2021
Location: Tampa bay
Posts: 28
Default Re: Aluminum pulley for M90 blower.

Quote:
Originally Posted by Brian View Post
Or, [machine work again] simply bore it out, press in a sleeve, [ideally steel - more durable], scotch key it in place, bore and key it to suit...
Yeah I do have a lathe, so I was thinking about that. I don't have an end mill though. Still may attempt this.

Sent from my SM-N986U using Tapatalk
32truck is offline   Reply With Quote
Old 12-03-2021, 12:41 PM   #9
32truck
Junior Member
 
32truck's Avatar
 
Join Date: Nov 2021
Location: Tampa bay
Posts: 28
Default Re: Aluminum pulley for M90 blower.

Quote:
Originally Posted by Bored&Stroked View Post
You'll probably need to have one custom made at a machine shop. Not a hard thing to do - but they'll need exact measurements on the shaft and keyway.
I've been calling around to a few machine shops without any luck yet.

Sent from my SM-N986U using Tapatalk
32truck is offline   Reply With Quote
Old 12-03-2021, 01:51 PM   #10
marko39
Senior Member
 
Join Date: Oct 2016
Location: harpursville ny
Posts: 1,038
Default Re: Aluminum pulley for M90 blower.

Quote:
Originally Posted by 32truck View Post
Bore .640 pulley diameter 4inches. Nah doesn't have to be aluminum.

Sent from my SM-N986U using Tapatalk
That is an odd bore size .640 = 41/64. Is that the shaft size? If it is 5/8 ( .625) I can probably help. Worst case would be boring out the 5/8 to 41/64.
marko39 is offline   Reply With Quote
Old 12-03-2021, 02:27 PM   #11
32truck
Junior Member
 
32truck's Avatar
 
Join Date: Nov 2021
Location: Tampa bay
Posts: 28
Default Re: Aluminum pulley for M90 blower.

Quote:
Originally Posted by marko39 View Post
That is an odd bore size .640 = 41/64. Is that the shaft size? If it is 5/8 ( .625) I can probably help. Worst case would be boring out the 5/8 to 41/64.
Yep Shaft size is .640

Sent from my SM-N986U using Tapatalk
32truck is offline   Reply With Quote
Old 12-03-2021, 02:50 PM   #12
Bored&Stroked
Senior Member
 
Bored&Stroked's Avatar
 
Join Date: Jan 2011
Location: Central Ohio
Posts: 5,012
Default Re: Aluminum pulley for M90 blower.

If it was mine, I'd make a steel blower drive flange - similar to a crankshaft blower pulley flange. The flange would have bolts to bolt on an aluminum pulley. This way you can change pulley sizes quite easily. The flange should have a centering ridge on it (like a crankshaft blower pulley).
Bored&Stroked is offline   Reply With Quote
Old 12-03-2021, 02:51 PM   #13
Bored&Stroked
Senior Member
 
Bored&Stroked's Avatar
 
Join Date: Jan 2011
Location: Central Ohio
Posts: 5,012
Default Re: Aluminum pulley for M90 blower.

Also, you might consider using a dual-belt lower pulley - if it will clear your cross-member. It is much better to have multiple belts than just one. If you're going to the trouble of coming up with a new pulley drive system, might as well make it better.
Bored&Stroked is offline   Reply With Quote
Old 12-03-2021, 03:10 PM   #14
Pete
Senior Member
 
Pete's Avatar
 
Join Date: May 2010
Location: Wa.
Posts: 5,374
Default Re: Aluminum pulley for M90 blower.

...

Last edited by Pete; 12-03-2021 at 08:27 PM.
Pete is offline   Reply With Quote
Old 12-03-2021, 03:48 PM   #15
32truck
Junior Member
 
32truck's Avatar
 
Join Date: Nov 2021
Location: Tampa bay
Posts: 28
Default Re: Aluminum pulley for M90 blower.

Quote:
Originally Posted by Bored&Stroked View Post
If it was mine, I'd make a steel blower drive flange - similar to a crankshaft blower pulley flange. The flange would have bolts to bolt on an aluminum pulley. This way you can change pulley sizes quite easily. The flange should have a centering ridge on it (like a crankshaft blower pulley).
Definitely like this idea. Actually this makes the most sense. Definitely looking into this. Thanks so much. I agree this is a poor design.

Sent from my SM-N986U using Tapatalk
32truck is offline   Reply With Quote
Old 12-03-2021, 03:50 PM   #16
32truck
Junior Member
 
32truck's Avatar
 
Join Date: Nov 2021
Location: Tampa bay
Posts: 28
Default Re: Aluminum pulley for M90 blower.

Quote:
Originally Posted by Bored&Stroked View Post
Also, you might consider using a dual-belt lower pulley - if it will clear your cross-member. It is much better to have multiple belts than just one. If you're going to the trouble of coming up with a new pulley drive system, might as well make it better.
I have about a 16th of an inch clearance with the crossmember unfortunately.

Sent from my SM-N986U using Tapatalk
32truck is offline   Reply With Quote
Old 12-03-2021, 04:27 PM   #17
marko39
Senior Member
 
Join Date: Oct 2016
Location: harpursville ny
Posts: 1,038
Default Re: Aluminum pulley for M90 blower.

The last piece of the puzzle is what size is keeway and are you using an A belt or B belt?
marko39 is offline   Reply With Quote
Old 12-03-2021, 05:48 PM   #18
32truck
Junior Member
 
32truck's Avatar
 
Join Date: Nov 2021
Location: Tampa bay
Posts: 28
Default Re: Aluminum pulley for M90 blower.

Quote:
Originally Posted by marko39 View Post
The last piece of the puzzle is what size is keeway and are you using an A belt or B belt?
Not sure on the size of the keyway. I will measure it over the weekend. Its at my shop. Thanks.

Sent from my SM-N986U using Tapatalk
32truck is offline   Reply With Quote
Old 12-03-2021, 06:36 PM   #19
Ggmac
Senior Member
 
Join Date: Jul 2016
Location: Lake worth Florida
Posts: 1,073
Default Re: Aluminum pulley for M90 blower.

Cant you cut another slot say at 180 degrees . If its not timing anything , Ive done this on a few shafts that were messed up .
Ggmac is offline   Reply With Quote
Old 12-03-2021, 06:39 PM   #20
32truck
Junior Member
 
32truck's Avatar
 
Join Date: Nov 2021
Location: Tampa bay
Posts: 28
Default Re: Aluminum pulley for M90 blower.

Quote:
Originally Posted by Ggmac View Post
Cant you cut another slot say at 180 degrees . If its not timing anything , Ive done this on a few shafts that were messed up .
Great suggestion, but unfortunately the entire hole got wallowed out.

Sent from my SM-N986U using Tapatalk
32truck is offline   Reply With Quote
Reply

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump

Sponsored Links (Register now to hide all advertisements)


All times are GMT -5. The time now is 04:27 PM.