Go Back   The Ford Barn > General Discussion > Early V8 (1932-53)

Sponsored Links (Register now to hide all advertisements)

Reply
 
Thread Tools Display Modes
Old 09-04-2014, 02:04 PM   #1
mfagan
Senior Member
 
mfagan's Avatar
 
Join Date: May 2010
Location: Kaufman, TX
Posts: 822
Default Vinegar in the block

I know that the use of vinegar had been discussed several
times to de rust the water passages in a flathead.

How much vinegar should be used, and what do you use to
neutralize when done?
mfagan is offline   Reply With Quote
Old 09-04-2014, 02:10 PM   #2
Torchie
Senior Member
 
Join Date: Jan 2012
Location: Northern Mi.
Posts: 355
Default Re: Vinegar in the block

Quote:
Originally Posted by mfagan View Post
I know that the use of vinegar had been discussed several
times to de rust the water passages in a flathead.

How much vinegar should be used, and what do you use to
neutralize when done?
Straight white vinegar. Just Flush with water. Or if your really concerned. Water with baking soda dissolved in it. But most use water only.
Vinegar is a very mild acid and it really doesn't need to be neutralized. Just kind of rinsed off.
There are also posts out there in regards to using certain dishwasher detergents as well. They do the same thing.
Torchie.
Torchie is offline   Reply With Quote
Sponsored Links (Register now to hide all advertisements)
Old 09-04-2014, 03:03 PM   #3
36Bill
Senior Member
 
36Bill's Avatar
 
Join Date: Jun 2011
Location: Oregon
Posts: 315
Default Re: Vinegar in the block

I used straight vinegar for two weeks and then back flushed with lots of water. Runs cool now.

Bill
__________________
The best way to have a friend is to be a friend. Howdy Doody
36Bill is offline   Reply With Quote
Old 09-04-2014, 03:15 PM   #4
Old Henry
Senior Member
 
Old Henry's Avatar
 
Join Date: Oct 2010
Location: Orem, Utah
Posts: 5,762
Default Re: Vinegar in the block

There is better than vinegar which is an acid that, from my tests, neutralizes before it's finished it's job. See this test comparing vinegar to Evapo-Rust: http://www.fordbarn.com/forum/showthread.php?t=123032 which uses a chelation process that doesn't quit till it's done and won't harm metal.
__________________
Prof. Henry (The Roaming Gnome)
"It is good to have an end to journey toward; but it is the journey that matters, in the end.” *Ursula K. Le Guin in The Left Hand of Darkness
Old Henry is offline   Reply With Quote
Old 09-04-2014, 04:42 PM   #5
mfagan
Senior Member
 
mfagan's Avatar
 
Join Date: May 2010
Location: Kaufman, TX
Posts: 822
Default Re: Vinegar in the block

Thanks to all! Old Henry I like the way you
do things.
mfagan is offline   Reply With Quote
Old 09-04-2014, 05:40 PM   #6
Doug-F1
Junior Member
 
Doug-F1's Avatar
 
Join Date: Jun 2014
Location: Winnipeg, Manitoba, Canada
Posts: 28
Default Re: Vinegar in the block

Sponsored Links (Register now to hide all advertisements)
I used 2 gal. straight vinegar and topped it off with water for only 24hr. and then back flushed with lots of water and used an air hose to get some action in the water as it was draining. It worked well however I think a few more days would have done a better job.
Doug-F1 is offline   Reply With Quote
Old 09-04-2014, 06:02 PM   #7
supereal
Senior Member
 
supereal's Avatar
 
Join Date: Jul 2014
Location: Iowa
Posts: 1,634
Default Re: Vinegar in the block

The acetic acid in vinegar takes a very long time, if ever, to reduce lime deposits in a block. The important thing is not to use anything that will attack the metal in the radiator. Years ago, we used a solution of "washing soda". I don't know if it is still available. Core sand, from the original casting, is usually hiding in he block. A coating of lime no thicker than paint, can reduce cooling efficiency by 40-50%. What is there is probably not going to move. If you use demineralized or distilled water, you won't add to the problem.
supereal is offline   Reply With Quote
Old 09-04-2014, 06:35 PM   #8
FrankWest
Senior Member
 
FrankWest's Avatar
 
Join Date: Sep 2013
Posts: 3,002
Default Re: Vinegar in the block

Don't leave the vineger in too long or the neighbors will begin calling you
"Little Douche Coupe" Rather than "Little Duce Coupe"
FrankWest is offline   Reply With Quote
Old 09-04-2014, 08:10 PM   #9
alanwoodieman
Senior Member
 
Join Date: May 2010
Location: upstate SC
Posts: 2,962
Default Re: Vinegar in the block

drain all water out, remove thermostat, fill with vineger and drive the car, usually takes a couple of days the heat/cool cycle seems to really help. did a 41 x-car and had to do it twice to get the crud out--runs cool now. flush with plenty of water-back flushing even helps more but tends to make a mees of the back flush operator
alanwoodieman is offline   Reply With Quote
Old 09-04-2014, 08:56 PM   #10
JM 35 Sedan
Senior Member
 
JM 35 Sedan's Avatar
 
Join Date: May 2010
Location: Near Rising Sun, Maryland
Posts: 10,856
Default Re: Vinegar in the block

I used straight white vinegar in my 35 last year. I left it in maybe a week (probably should have been longer) and that brought out all kinds of crud. Ran some baking soda in water for a couple days and drained that before going back to 50/50 antifreeze and water. May try some of that Evapo-Rust that Old Henry suggests the next time it needs cleaning..
__________________
John

"Never give up on what you really want to do. The person with big dreams is more powerful than one with all the facts". Albert Einstein
JM 35 Sedan is offline   Reply With Quote
Old 09-05-2014, 06:53 AM   #11
OhioRick
Senior Member
 
OhioRick's Avatar
 
Join Date: May 2010
Location: Ohio
Posts: 174
Default Re: Vinegar in the block

100% vinegar for a week many times running the car everyday. Heated vinegar works better. I continually drained it and installed new until it was crystal clear.
Smelled like French fries.
OhioRick is online now   Reply With Quote
Old 09-05-2014, 09:15 AM   #12
hotrodderhaag
Senior Member
 
hotrodderhaag's Avatar
 
Join Date: Sep 2012
Location: Mooresville Nc
Posts: 137
Default Re: Vinegar in the block

one caution with vinegar.. if you decide to run it.. i took off the radiator hoses and i cut squares of stainless steel screen and place it over all radiator connections then slid the the hoses back on and clamped it tight.. this keeps the chunks of rust from plugging up a good radiator.. it happens faster than you think. there is no shop that can get it out of the cores if it happens.... ask me how i now this :/
hotrodderhaag is offline   Reply With Quote
Reply

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump

Sponsored Links (Register now to hide all advertisements)


All times are GMT -5. The time now is 03:31 PM.