Go Back   The Ford Barn > General Discussion > Model A (1928-31)

Sponsored Links (Register now to hide all advertisements)

Reply
 
Thread Tools Display Modes
Old 06-10-2011, 07:47 PM   #1
MARKA
Member
 
Join Date: May 2010
Location: Melbourne Australia
Posts: 39
Default Cannot get into first or reverse

I drove my 1930 Coupe for the first time yesterday and when I depressed the clutch and waited for up to 30 seconds with the car stopped I could not engage first or reverse gears withot the gear clashing.

No matter how long I wait with the clutch depressed makes no difference and the first and reverse gears will not stop spinning for me to engage without clashing.

I have a vey low idle speed set as well .

I can engage second and top gears without a problem once the car is under way.

I have the correct Mobil Gear oil that is recommeded by people on Fordbarn.

Does anyone have any ideas what is wrong. ?

Thanks Mark.
MARKA is offline   Reply With Quote
Old 06-10-2011, 08:13 PM   #2
Tom Wesenberg
Senior Member
 
Tom Wesenberg's Avatar
 
Join Date: May 2010
Location: Mpls, MN
Posts: 27,582
Default Re: Cannot get into first or reverse

It sounds like the clutch needs adjusting, or maybe one of the clutch arms is cracked or broken. Remove the inspection cover from the clutch housing top and see how much the throwout bearing moves forward when you push the clutch pedal to the floor. The clutch should have about 1" freeplay, then start pushing the T/O brng forward.
Tom Wesenberg is offline   Reply With Quote
Sponsored Links (Register now to hide all advertisements)
Old 06-10-2011, 09:51 PM   #3
MARKA
Member
 
Join Date: May 2010
Location: Melbourne Australia
Posts: 39
Default Re: Cannot get into first or reverse

Tom , I checked that the throw out bearing moves forward and the arms retract o.k.

I was thinking that the clutch plate is frozen .

The car has been in a body and paint shop for 2 years without being run .

Is thier a method to free up a frozen clutch plate. ?
MARKA is offline   Reply With Quote
Old 06-10-2011, 09:57 PM   #4
Tom Wesenberg
Senior Member
 
Tom Wesenberg's Avatar
 
Join Date: May 2010
Location: Mpls, MN
Posts: 27,582
Default Re: Cannot get into first or reverse

I would just start the car in first gear then step on the clutch and brake at the same time and see if that doesn't break it loose. You could also push the clutch down and floor the gas and release it several times. Hopefully one of these will free the disc.
Tom Wesenberg is offline   Reply With Quote
Old 06-10-2011, 09:57 PM   #5
John Duden
Senior Member
 
John Duden's Avatar
 
Join Date: Jun 2010
Posts: 1,854
Default Re: Cannot get into first or reverse

MY AA TRUCK IS DOING THE SAME THING! Except it can't keep oil in it and it has a wicked sound when driving, It has a single disk clutch in it, someone replaced the origional Multi disk clutch,
i think that it is junk so i am going to get a multi disk tranny, and be done,

on the Early AA trucks, the daul high gets in the way of the stop light switch and it cannot be used, but with a multi disk clutch tranny it will solve it
John
John Duden is offline   Reply With Quote
Old 06-11-2011, 02:59 AM   #6
MARKA
Member
 
Join Date: May 2010
Location: Melbourne Australia
Posts: 39
Default Re: Cannot get into first or reverse

Sponsored Links (Register now to hide all advertisements)
You are not going to believe this.
The coupe when I purchased it had a a vinyl floor mat.
I have put Baron Le Bonney kit in th car as well as floor carpets.

When I took the carpets out to check the clutch out, I also had to remove the rubber pedal pads that I had also added.

Well I started "nessie "(Car given the name of Elliot Ness of the untouchables fame )
and lo and behold no more spinning first and reverse gears. Just slips into the stationery gears as it should with the clutch in.

The lesson is if you add carpets and pedal pads remember to deduct 1/2 inch from the specfied 1 inch of free play to compensate for the loss of 1/2 of pedal travel.

Thanks Tom for pointing me in the right direction.
The simple things are what should be checked first but who would have believed that this was the problem.

Thanks
Mark.
MARKA is offline   Reply With Quote
Old 06-11-2011, 10:08 AM   #7
JoeWay
Senior Member
 
JoeWay's Avatar
 
Join Date: May 2010
Location: Quincy CA
Posts: 752
Default Re: Cannot get into first or reverse

Quote:
Originally Posted by MARKA View Post
...The lesson is if you add carpets and pedal pads remember to deduct 1/2 inch from the specfied 1 inch of free play to compensate for the loss of 1/2 of pedal travel...

Thanks
Mark.
Mark, your pressure plate fingers may be mis-adjusted, requiring extra pedal travel before full release. The clutch should be fully released before the pedal gets to the floor, even with 1/2"of extra pad.

Note that pedal free-play decreases as the clutch disk wears, so you will need to keep a close eye on the free-play adjustment if you drive it much.

Joe
__________________
1929 Tudor
since 1962
Feather River A's
JoeWay is offline   Reply With Quote
Reply

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump

Sponsored Links (Register now to hide all advertisements)


All times are GMT -5. The time now is 07:24 AM.