The Ford Barn

36tudordeluxe · 08-26-2016, 01:30 PM

The directions that came with the FLEX HONE recommend 500-800 RPM; my Milwaukee drill is rated at 400 low speed, 1500 high speed but I don't know if these speeds are under load. My question is do I use the low or high speed setting?

Capt Kirk · 08-26-2016, 01:57 PM

I'd use the low speed. If you use high, you're gonna feel like you're churning butter the old fashion way!

51 MERC-CT · 08-26-2016, 01:59 PM

The lowest speed the drill will run, regardless of ratings or settings.

36tudordeluxe · 08-26-2016, 02:06 PM

Okay, low speed it is, thank you.

36tudordeluxe · 08-26-2016, 02:16 PM

How does this look, haven't washed the cylinder with warm soapy water yet?

Ronnieroadster · 08-26-2016, 03:01 PM

Sponsored Links (Register now to hide all advertisements)

You dun good

36tudordeluxe · 08-26-2016, 03:15 PM

Quote:

Originally Posted by ronnieroadster

you dun good

thank you!

Ronnie · 08-26-2016, 03:15 PM

Quote:

Originally Posted by 36tudordeluxe

How does this look, haven't washed the cylinder with warm soapy water yet?

Lookin like a pro job from here. After the final clean give it a wipe with oil to preserve it until assembly.

R

BUBBAS IGNITION · 08-26-2016, 03:16 PM

Also depends on the lube used .........slow speed with marvel is usually pretty good.....

36tudordeluxe · 08-26-2016, 04:23 PM

Going to give it a bath and then wipe it down with oil and wait for the rings to get here. Thanks for the help guys.

Ronnie · 08-26-2016, 10:47 PM

Carry on and keep smiling it was quite easy wasn't it.

R

Ronnie · 09-28-2016, 10:11 AM

What is the latest update on your repair?

R

36tudordeluxe · 09-28-2016, 11:00 AM

Got sidetracked with minor issues on the '36 and about to button that up in a few more days. Got the Hastings rings from my machinist. Looks like the gaps on the rings will be about .015, little larger than ideal but should be okay?

Bored&Stroked · 09-28-2016, 12:09 PM

Looks like you're getting it done - nice work! The ring gap of .015 will be just fine - just take a file to break the sharp corner/edge on both sides of the gap (keeps them from scratching the bore). You only need to just barely take the corner off - don't file away on it!

Ronnie · 09-28-2016, 12:32 PM

Quote:

Originally Posted by 36tudordeluxe

Got sidetracked with minor issues on the '36 and about to button that up in a few more days. Got the Hastings rings from my machinist. Looks like the gaps on the rings will be about .015, little larger than ideal but should be okay?

Things are good remember the ring gaps are stated as minimum gaps not max .015" will be great as already stated. How did your glaze break and cleanup turn out or need I ask?

Good to see another fine home grown project move along.

R

36tudordeluxe · 09-28-2016, 09:59 PM

Will carefully file corner/edge on the rings.
Should be able to get to this in the next day or two.
Appreciate the help and encouragement.

Ronnie · 09-28-2016, 10:08 PM

Just use some 320 paper on a flat file to do the job but it really isn't required if you didn't file fit the rings.

R

08-26-2016, 01:30 PM	#1
36tudordeluxe Senior Member Join Date: Feb 2012 Location: Las Vegas, NV Posts: 1,260	Drill speed for flex hone? The directions that came with the FLEX HONE recommend 500-800 RPM; my Milwaukee drill is rated at 400 low speed, 1500 high speed but I don't know if these speeds are under load. My question is do I use the low or high speed setting?

08-26-2016, 01:57 PM	#2
Capt Kirk Senior Member Join Date: May 2015 Location: Clarkston MI Posts: 830	Re: Drill speed for flex hone? I'd use the low speed. If you use high, you're gonna feel like you're churning butter the old fashion way! __________________ 35 Ford Cabriolet 56 Chevy Pickup 63 VW Bug Empty wallet

08-26-2016, 01:59 PM	#3
51 MERC-CT Senior Member Join Date: May 2010 Location: East Hartford, Ct Posts: 5,898	Re: Drill speed for flex hone? The lowest speed the drill will run, regardless of ratings or settings. __________________ DON'T RECALL DOING SOMETHING FOR MYSELF BASED ON SOMEONE ELSE'S LIKES OR DISLIKES

08-26-2016, 02:06 PM	#4
36tudordeluxe Senior Member Join Date: Feb 2012 Location: Las Vegas, NV Posts: 1,260	Re: Drill speed for flex hone? Okay, low speed it is, thank you.

08-26-2016, 03:01 PM	#6
Ronnieroadster Senior Member Join Date: Dec 2010 Location: East Coast in CT Posts: 1,778	Re: Drill speed for flex hone? Sponsored Links (Register now to hide all advertisements) You dun good

08-26-2016, 03:16 PM	#9
BUBBAS IGNITION Senior Member Join Date: May 2010 Location: SPEEDWAY INDIANA Posts: 4,148	Re: Drill speed for flex hone? Also depends on the lube used .........slow speed with marvel is usually pretty good..... __________________ If it Makes Spark, we do it !!!! www.bubbasignition.com [email protected]

08-26-2016, 04:23 PM	#10
36tudordeluxe Senior Member Join Date: Feb 2012 Location: Las Vegas, NV Posts: 1,260	Re: Drill speed for flex hone? Going to give it a bath and then wipe it down with oil and wait for the rings to get here. Thanks for the help guys.

08-26-2016, 10:47 PM	#11
Ronnie Senior Member Join Date: May 2010 Location: Canada Where it snows Posts: 2,059	Re: Drill speed for flex hone? Carry on and keep smiling it was quite easy wasn't it. R

09-28-2016, 10:11 AM	#12
Ronnie Senior Member Join Date: May 2010 Location: Canada Where it snows Posts: 2,059	Re: Drill speed for flex hone? What is the latest update on your repair? R

09-28-2016, 11:00 AM	#13
36tudordeluxe Senior Member Join Date: Feb 2012 Location: Las Vegas, NV Posts: 1,260	Re: Drill speed for flex hone? Got sidetracked with minor issues on the '36 and about to button that up in a few more days. Got the Hastings rings from my machinist. Looks like the gaps on the rings will be about .015, little larger than ideal but should be okay?

09-28-2016, 12:09 PM	#14
Bored&Stroked Senior Member Join Date: Jan 2011 Location: Central Ohio Posts: 5,906	Re: Drill speed for flex hone? Looks like you're getting it done - nice work! The ring gap of .015 will be just fine - just take a file to break the sharp corner/edge on both sides of the gap (keeps them from scratching the bore). You only need to just barely take the corner off - don't file away on it!

09-28-2016, 09:59 PM	#16
36tudordeluxe Senior Member Join Date: Feb 2012 Location: Las Vegas, NV Posts: 1,260	Re: Drill speed for flex hone? Will carefully file corner/edge on the rings. Should be able to get to this in the next day or two. Appreciate the help and encouragement.

09-28-2016, 10:08 PM	#17
Ronnie Senior Member Join Date: May 2010 Location: Canada Where it snows Posts: 2,059	Re: Drill speed for flex hone? Just use some 320 paper on a flat file to do the job but it really isn't required if you didn't file fit the rings. R

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode